Search the Community

Showing results for tags 'serial error'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 165 results

  1. Hi,     I'm trying to communicate Omron CP1E unit with PC via serial port using hostlink protocol.  I need to read the Timer/Counter SV value and write the timer/counter SV values to the PLC.  I'm able to use other C mode commands (like RC (timer/counter PV read), WC (timer/counter PV write) etc.) but when I give the command for Timer/Counter SV Read 1 which is R#, I get the response as IC (Undefined Command).   How do I write or read the timer SV Values?  Example command and response : @00R#TIMH001028*  (TIMH is the high speed timer, 0010 is the timer number and 28 is the FCS) Response: @00IC4A* Is is that CP1E doesn't support these commands? If so what is the equivalent command that I should send inorder to perform this? Please help.  
  2. Hi guys, so i'm trying to send data to plc omron cp2e-n40dra via RS232C, I use RXD and TXD but it looks like my programs are wrong, the indicator of RS232C are on everytime i send the data so it looks like PLC receive my data but when i see it in memory PLC D i can't find any data stored. Can anyone help me please? I attach my Gdrive for pictures since i can't upload pictures in here *The data that i sent is in ASCII https://drive.google.com/drive/folders/1GPXa1U1PLMU2WKmo4YRPe32wHHyVCGUv?usp=sharing
  3. Error message

     hi everyone i m traying to   write to plc  a program and getting this message then program is not downloading to plc   'there is a device in the program (main) that is outside of the range  check the program and currect the device that outside of the  range ' I m using mitsubishi fx3ga-60mt  plc. please suggest me about it .                              thank you          
  4. Hi, I have an Omron NSJ5-SQ00B-M3D Programmable Terminal (HMI) that I am trying to get to communicate with an Omron CJ2H PLC through a DeviceNet module (DRM21) in the main PLC rack.  I don't see how to configure CX-Designer to communicate via DeviceNet.  How is this done?  Many thanks for any help.
  5. Hello,  When i get error 2003 with sktTCPAccept what is causing it? Can it be caused if something was left open from previous session, is something wrong on server or client side? From F1 help i think error causes can be narrowed down to either open/close processing is in progress for SrcTcpPort although it doesnt specifically state that it causes error 2003. After closing port is there delay needed before i can use sktTCPAccept again?
  6. Hello, We have a FX3G connected to a FX3U-ENET-ADP inside a main cabinet. We are then using that master PLC to collect data from 2 other fx3g plcs in a node:node serial network. I was assigned a small project of pricing out some wireless adapters so we can upload/download to the two slave plcs. My question is, is it possible to upload/download programs to/from the slave plcs through the ENET adapter and serial network in the main plc? It would save us some money if possible. thanks.
  7. OMRON NS5-SQ10B-V2

    Hello, I have an issue with NS-5 HMI. During transferring new program into HMI, after rebooting I get message: ERROR No.10: file system error: please recover the system program. What is procedure from where I can recover this HMI? I didn't find  folder on CX-Designer under C:\Program Files\OMRON\CX-One\CXDesigner\RecoverUpdate. Is there other way to fix this ERROR? I download firmware and copy it to the CF card. When I insert CF card into NS-5, and after power on unit, RUN LED light become steady orange for 10seconds and than it become steady green. Screen is black and there is not possible to do (chose) nothing. CF card is original OMRON card and wasn't formatted. How to solve this issue???
  8. OMRON CJ1W-CT021

    MY OMRON CJ1M CPU12 SHOWS UNIT NUMBER DUPLICATE ERROR. ERROR CODE IS 0X80E9.  THE CPU HAS TWO NUMBER OF HIGH SPEED COUNTER IN A RACK SOME AND I/O UNITS.  PLEASE HELP HOW TO SET MACHINE NUMBER (ROTARY SWITCH)  IN OMRON CJ1W-CT021 IF TWO UNIT CONNECTED IN ONE CPU. PLEASE SEE ATTACHED PICTURE. CJ1W-CT021.bmp
  9. Proface with Serial Printer

    Dear Sir, Good day. I facing difficulty on using proface to print out the data using serial printer. I did follow all the instruction on proface reference manual but still fail to print out anything. Anyone here having experience on this issue? Thanks. 
  10. GT work 3 installation error

     GT work 3 installation....  How to clear this error    ' because the path name of installer folder is too long installation process is discontinued. Please move installer folder to the place which the path name became 87 or less letter and execute setup.exe onces again'  
  11. Error Indicator on FX3U-ENET-ADP

    Hi all, I have finished installing ethernet adapter module FX3U-ENET-ADP on the FX3U-48M PLC. From the ethernet module, i connected it to a wireless router and then i am planning of connecting to the ethernet module using GXWorks 2 on my laptop through wireless router. On the ethernet module, the error indicator LED is on (red). From the FX3U-ENET-ADP, it means that there might be setting or hardware errors.  I am asking if i have missed some steps on the installation process and if any of you have experience with similar problems. Thanks in advance for the answers.
  12. Dear All My system includes Module 1747-SDN which controls Micrologix via Module 1761-NET-DNI but Now Module 1761-NET-DNI is broken and I replace a new but the system issue error on both Module 1747-SDN and 1761 -NET-DNI. I don't know what I have to do when I replace Module 1761-NET-DNI? Thank you very much
  13. connection to omron CJ1M PLC

    I have an omron PLC (CJ1M type) at home which I would like to connect to, however, lately, I can't anymore.  I'm trying on two different PC's a newer and an older one, both running on windows 10. 1 is just mentioning a DLL error and I can't even start cx-programmer, the other one seems to work, however, when I try to go online it always fails I'm using a usb to serial device and after some searching on the net, I thought the issue was with the prolific driver.  I tried all kind of fixes, but nothing seemed to work.  I have now purchased another device, the XS8801 from usconverters and installed the latest driver.  I have checked if cx programmer is set to work with the correct port and this is the case. My knowledge is very limited but I would really want to connect to that PLC again, so hoping someone out here is able to help me. Thanks a lot    
  14. Hi,     I am trying to establish communication between master and slave through modbus rtu rs485. But I am experiencing error code 7378h. I already tried to make the values of Request Interval Timer from 100 to 200 and Broadcast Delat Value from 50 to 100. But the error still persist. Any tips how to solve this issue? There is no error on the slave evices.
  15. Check serial connection to Omron PLC

    Hello, I am building an application in CitectSCADA and I want to communicate with an Omron Sysmac CS1G. The connection between the plc and the Citect computer is through an ethernet to serial adapter (the computer doesn't have com ports on board). I'm having some difficulty establishing the communication and I want to make sure that I can actually reach the plc. Is there a way to check that the computer can reach the plc over the serial connection without using CX programmer? Maybe using Hyper Terminal, Putty or something similar. Thank you, Liron
  16. HI All,  I have an issue with my SCU32 communication.  Back ground Two SCU32s  (top and bottom side) connected via a 1100M datacable  using port1 ( 9600bps,  8-2-E, start code FF, end code FE, Tx save to d1000-d1200 , Rx save to d2000-d2200). PORT2 of bottom SCU32 is connected to a compass( 2 wire, 8-1-N, 19200 bps, serial gateway MODBUS ). Refer to photo Issue  Without compass, the receiving data at top is very stable and is didn't see any fluctuation. But if is compass is connected at bottom side port2, there is a fluctuation at the top side RX data(specifically d2000-d2005 ) .  I checked the data a bottom side TX (d1000-d1200) and it is stable. Only after sending the data and Receiving at Top side, then only the starting words fluctuate. I am not sure sure what is wrong, I am using logical ports for the DTXDU/DRXDU and compass.   Appreciate all your feedback and suggestions.  
  17. Hi every one ! I cannot use register D128 - D255 in the program when I create a program that uses the Block function in the PLC mitsubishi FX1S, it gives an error :  A device of the device range set in the device/label automatic-assign setting or a device which cannot be used due to system reservation is being used.Help me,Thanks !
  18. Folks, we have a set of Mitsubishi Q12PRHCPU (redundant) running effortless since many years. CPU-A as standby and CPU-B as Control. Recently we noticed BATT low alarm on CPU-B. So we arranged for a spare battery Q6BAT and started the procedure as per manual(attached procedure and flow chart). We did memory copy from Control to standby (as prescribed precaution) and did the Reset of Standby PLC CPU-A. Memory copy from B to A completed successfully 100%. But the BACKUP LED did not turn Green from Red & Error LED kept flickering on standby CPU-A. CPU-B remain in Control but backup LED turned RED. From system monitoring we found that there is a Error 6000 (FILE DIFF.) observed in One of the .QPG (program 00-MDBUS.QPG). We tried to reset it but were not successful. We are surprised that why does the program differs when it was copied from CPU-B to CPU-A using the memory copy. Still we did the VERIFY and found no difference between the programs in CPU-A & CPU-B.  Can anyone explain the cause of this issue and the solution. Please note that the CPU-B is still in control and plant is running. Backup LED on both CPU are red which means (redundancy loss) and error LED on standby CPU-A is flickering RED. There is no error in the CPU-A (Control) -we checked this using the GX Developer. Also attached here are the image of the error and error help. Thanks in advance. Battery Replacement procedure.pdf Battery Replacement procedure-Flow Chart.pdf Error.pdf MELSEC QCPU ERROR CODE 6000 FILE DIFF.pdf
  19. Hi! I would like to ask how could I send data from PC to CJ1M PLC, by SCU-41 module and RS232 cable, in order to activate an actuator (LED)? In my environment, I have a sensor that sends data from PLC to PC (I'm checking data, "HelloWrld" with Putty), with this configuration: And I have another section where I want to read the data from the PC in ordr to activate a LED I would like when I send for example a letter 'a' trough Putty, the LED activates. How could I do that? Thank you very much!
  20. Hi All need to convert a Decimal Value into Ascii code to send out on serial 485. eg. Weight comes in as Int 12345 i need to send it out in Ascii as 23 32 20 31 32 33 34 35. I have created an array 0 of 8 (Word) DB. Is there an easy way split the int into Digits convet in into HEX and slot the value into the various array positions? Array 0 of 8 = 23 means # Array 1 of 8 = 32 means 2 (Station ID) Array 2 of 8 = 20 means Space Array 3 of 8 = 31 means 1 Array 4 of 8  = 32 means 2 Array 5 of 8 = 33 means 3 Array 6 of 8 = 34 means 4 Array 7 of 8 = 35 means 5 Array 8 of 8 = D means CR    this sends the value of 12345 to Display ID 2 . need help to convert the decimal number in ascii. the decimal number will be max of 5 digits and less than 32000   any help will be greatly appreciated.
  21. Hey everyone, I have a CJ1M PLC with a CJ1W-SCU21-V1 serial card. It is unit 6 and I am using port 1. I have bit 1659.06 ((1500 + 25 * Unit #) +9, bit 6) as "characters in buffer" but it never comes on (data is being received through the port successfully). It is on No-Protocol mode. Does anyone have any ideas as to how I can detect data in the buffer?
  22. Sysmac Cj2m Cpu35

    Dear All,  Need your help. I have problem with plc cj2m cpu35. After power trip plc error. Err HE Ip 01..what is mean? plc also connected with one pc using ethernet cable. Any suggestion need to do... 
  23. Serial comm with FX1N PLC

    I need to communicate with a Mitsubishi PLC using Matlab. To do that, I open a serial communication with the appropiate parameters (7,e,1,9600), and write an ASCII message based on the manual I have (attached). I have tried examples as the one in the attached image. The response starts with a 6, that is, the ASCII number for ACK, so something must be working. But the rest of the response is junk (149, 149, 149...), although its length depends on the input length (if I add terminator, the response is longer, and so on). I am completely stuck. Some information that might be helpful: I am using a Serial to USB converter that I have used successfully with other PLC (which used Modbus, so everything was easier) There's a VB application (of which I don't have the code) that is able to connect to the PLC (I need to connect directly without using this intermediate app). I have decompiled it trying to get some info, but was just able to confirm the 7,e,1,9600 parameters, since the rest of the code is too mangled to analyze The attached manual was sent to me by the guy who designed the PLC and its ladder code, so I guess it is the correct one I have tried the echo mode (TT) to no avail, response is always the same I have some doubts regarding the reading of a value (see attached image). Why is there a second message from the PC? Shouldn't I just need to read the response? GX Developer tells me that the address D8120 (which is supposed to define the comm format and protocol) contains a 0, which seems weird. Any help or hint would be greatly appreciated. Thanks jy992d69901e.pdf
  24. Hi everyone! I got this machine with a CP1H PLC and NS8-TV00B-V2 as PT. I was told that they were working fine, but suddenly, It appeared a communication issue: black screen and "connecting..." at right bottom. I dont know if It is a configuration problem or some hardware damage.  These are the configuration in the PT and the PLC. The communication is through RS232 Serial.  I tried to communicate another PT screen with the same communication settings and IT WORKED!. ' I've been thinking that, perhaps, the serial port A is damaged, I have tried to set port b, but I havent could. How can I configurate PORT B??   THANKS...  
  25. Sysmac Cj2m Cpu35

    Dear All,  Need your help. I have problem with plc cj2m cpu35. After power trip plc error. Err HE Ip 01..what is mean? plc also connected with one pc using ethernet cable. Any suggestion need to do...