Search the Community

Showing results for tags 'dinamic speed change'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 46 results

  1. Hmi temperature delta

    I have connected 2 temperature devices with him delta with plc delta by rs485. When I run plc I can see the temperature change on pc but the problem in hmi  it's give errors. Com 2 errors  I need someone help me to connect these devices please 
  2. Hello everyone, I have a Kinetix 6000 CIP drive (unwind) and I need to control its speed by a PID controller. I have everything working except the MCD instruction doesn't pick up on the PID output value change. It changes the JOG speed, which I use to control the unwind, if I set the speed manually, which is slow. The PID changes the speed almost continuously. Any suggestions are welcome. This is how I'm attempting to control the speed: A1_r_JogSpeed = PID output value   Thank you    
  3. HSPsO

    I am using fatek FBs 32MN PLC. i need to run the nema stepper motor synchronized with induction motor's speed with some ratio. in my case the speed of stepper motor will change as the speed of induction motor changes its speed, may be many times in a second. Problem is that the speed of stepper will be constant as before until i have to disable and then enable again HSPSO function. is there any solution that i can dynamically change the speed of stepper without disable and enable HSPSO function ?
  4. Hello Everyone, I am struggling with interfacing Incremental encoder with FX5U PLC, Does anyone have parameter setting and sample program for same. i am unable to fetch counts...   Encoder: 500ppr, 24V line drive, A-B phase,  PFA datasheet
  5. Folks, we have a set of Mitsubishi Q12PRHCPU (redundant) running effortless since many years. CPU-A as standby and CPU-B as Control. Recently we noticed BATT low alarm on CPU-B. So we arranged for a spare battery Q6BAT and started the procedure as per manual(attached procedure and flow chart). We did memory copy from Control to standby (as prescribed precaution) and did the Reset of Standby PLC CPU-A. Memory copy from B to A completed successfully 100%. But the BACKUP LED did not turn Green from Red & Error LED kept flickering on standby CPU-A. CPU-B remain in Control but backup LED turned RED. From system monitoring we found that there is a Error 6000 (FILE DIFF.) observed in One of the .QPG (program 00-MDBUS.QPG). We tried to reset it but were not successful. We are surprised that why does the program differs when it was copied from CPU-B to CPU-A using the memory copy. Still we did the VERIFY and found no difference between the programs in CPU-A & CPU-B.  Can anyone explain the cause of this issue and the solution. Please note that the CPU-B is still in control and plant is running. Backup LED on both CPU are red which means (redundancy loss) and error LED on standby CPU-A is flickering RED. There is no error in the CPU-A (Control) -we checked this using the GX Developer. Also attached here are the image of the error and error help. Thanks in advance. Battery Replacement procedure.pdf Battery Replacement procedure-Flow Chart.pdf Error.pdf MELSEC QCPU ERROR CODE 6000 FILE DIFF.pdf
  6. Hello all I am have FX3G PLC, where i am trying to use SPD function for speed monitoring and controling. currently i am working on software only. I am using x4 as input (s1) , sk1000 (s2), and d4 (D) in monitoring mode when i am forcing X4 to ON/OFF ,  there is no any value change occure on d4 i have tried to change the s2 value from k1000 to k10000, but not fruitful i need your valuable support to confirm that my primary setup is correct or not and what things are required/missing attached program screeshot  
  7. Hello there, I am using a Kinetix 5700 drives to control bunch of axis. HW used : 5069-L320ERMS2 GurdsLogix, 2198-S086-ERS4 Servo Drive with MPM-B2152M-M motor and the 843ES-SIP12BA6 safety encoder. All is working fine except I can't figure out how to dynamically change an axis velocity  controlled by a MAG instruction. I have a virtual master axis controlling the velocity and each physical axis is controlled by a MAG instruction with a gear ratio. In my safety program I have SFX and SLS function block used to determine the safe speed limit. The  SLSLimit output of the SLS function block is linked to a SS1 Request of my servo drive. This causes the axis to stop when safe speed limit acceded.  What I'd like to be able to do is to dynamically change velocity (limit it to safe speed if SLS instruction is active) of each axis without having to change the gearing ratios and thus avoid the SS1 safe stop action.  I know how to do that using JOG or MOVE but is it even possible to do that using the MAG instruction? Regards Martin
  8. FX5U high speed counter

    Hi All Does anyone know if it's possible to simulate the HSC function using just the software? I'm using the Hioen command but I want to try and simulate it if possible. Thanks in advance Scott
  9. If it is about changing Gmail ID on phone it is advisable to open the device settings application further at the top the user should click the personal information account then under the “Profile” or “contact info” the user should make the necessary changes. If you are still looking or searching for more information than in that case it is advisable that the user gets connected with the certified Gmail technicians. Lines are open for help and support all the time there is no such issue that cannot be resolved by the Gmail technical team.
  10. Hello guys, I am running an application for packaging measurement using a sick DFS60B incremental encoder (programmable from 1 to 10000 PPR). In more detail, it passes packaging on a conveyor belt and we have created an inspection station and an expulsion station (defective packaging), so we use the encoder to check at specific points of the packaging for defects (we use special sensors to check defects). ) (there are four in total). However, the problem we are having is the following: When reading the encoder in the PLC, the same means that performs "jumps" and does not enter the windows (GRT and LES) created on the ladder, ie, as if it were not continuous. . I understand that because the VHSC24 card works at 1 MHz in counter mode, this type of problem should not occur according to our application is not even 100 KHz. For example, our case: Using 1000 PPR and the motor speed (coupling output) is 3600 RPM (in practice it is around 1750 RPM) the frequency is calculated as follows: F = (PPR X RPM) / 60. : F = (1000x3600) / 60 = 60 KHz, ie 60 KHz is much less than 1 MHz, I think this kind of problem does not occur. Application Info: . Studio 5000 V31 . PLC Model: Rockwell 1769 - L19ER-BB1B CompactLogix 5370 . Encoder Card: 1734-VHSC24 / C . Incremental Encoder: Sick, DFS60 up to 10,000 PPR and HTL Electrical Interface. Using a 200 mm circumference / perimeter wheel. . Motor Nameplate Data: 1670 RPM, 0.37 kW / 0.5 HP, 60 Hz . Inverter: Weg CFW500, Output Frequency 62 Hz. Card Settings we use RPI: 2 ms Type: Counter, but we already use it as Encoder X1 Store Count Mode: Disabled Filter: No Filter, but we use 50 KHz and 5 Khz filters in our tests. Counter Attenuator: 1 Wiring Diagram VHSC24 We turn on encoder A at input 0 and encoder Aret at input 1 In logic (Structured Text) Using the PMUL instruction to convert encoder (Pulse) data to mm scale. (Ladder) The window comparisons part (GRT and Les) and other part of the process. We emphasize that we performed the tests also only with the reading and comparison part of the data, excluding the other parts, precisely to verify the issue of Scan, but the problem persisted. If anyone here in the forum has some information that can help us, I would appreciate it.
  11. Hello everyone, I have a problem with packing machine. There are some issues with one of the axis, when axis actual position is near to 1800000 some error appear and operator has to turn off machine on main contactor. This axis is working in Linear mode. I think that rotary mode would be better for this axis. And here is my question. Which instructions, and what options i should change/check when i change count mode in axis's options. Can any1 point me some manuals to read or give me some advice ? Thank you in advance.  
  12. Hi, I can’t find an answer to the following and I was advised to ask it here.I’m programming an Omron CJ2M with an MD212 high speed I/O card. I usually do all my programming in Structured text, simply because I like it a lot over ladder or sft.Now, if I want to read the hight speed counter (incremental encoder), I have to make a ladder section and use the PRV instruction to store the present value in a chosen location.The manual says the current PV is stored in A271, but I can’t get a readout there. Apparently the only way to read it is through this instruction.Does anyone know if there is an equivalent to the PRV instruction for Structured text? or another way perhaps? Again, when I check the actual memory adress, there’s no value there withouth the use of the PRV instr.
  13. I am controlling the powerflex 527 drive with MSO instruction, first setting the drive on and then running the motor with MAJ instruction. After MSO instruction, motor is rotating about 2 sec and then stops to wait the  MAJ. I have not find any solution for this. My configuration is frequency control, no feedback, sensorless. One hint i found from the rockwell pages but it did not help me. Rated slip speed is set to zero.  
  14. Q06UDEHCPU MELSECQ Upload

    Hello ,  I dont have experience with Mitsubishi PLC.  I want to do a modification on the ethernet configuration but i dont have the source code .  According the information that i read we can use GX IEC developer or GX developer but my question are :  Can i upload and download the program with GX developer?  Even if was previous developed with GX IEC Developer i will not do any change on the code only on ethernet configurations , add a MC communication. I have another concern about the profibus module. For the profibus is necessary another program right ? But if i don't want do any modification on the profibus is dont need it, right?  My experience on Siemens when is necessary do a modification on the hardware configuration. I should have all the hadware configuration " right"  it means if i have profibus i should have the right GSD to allow do modification on the configuration .  But on Mitsubish i can´t understand that well . Regards  Roberto Fonte  
  15. Hello      I have a cj2m processor and md211 module and I want to read position from rotary encoders who are put on the stepper motors. I use high speed counters to count the number of(I made settings like in documentation) but every time I read velocity.   In first two picture I have 3 blocks for PRV function , I set port specifier [#0, #1 and #3] because on this ports I command 3 axis. Please help me!              
  16. hallo everyone ...i use mitsubishi Q00UJCPU and QD77MS2.. i try to make a speed control program and the speed wants to be changed during servo operating, i use dedicated instructions ZP. PSTRT1 (axis 1) and have tryed but it was only successful to change speed with "change speed control" function once ... is it like it? cannot change "change speed control" many times when servo operations?
  17. PLC Mitsubishi High Speed Counting

    Dear friends, I want to calculate the flow with the help of a flow sensor that has 650 pulses per litre. My question is that can i do that with the help of plc FX1N ? can plc count such fast pulses and how .. need some help
  18. About InverterRefresh

    Hı guys,  I will design new project  but I dont know that how can ı use  FB  at the   attachmend files ı wanna send   speed  referances  for 23 motors with rs 485  I will not use   start and stop  function  for ınverters with modbus   ıt  will be doing   probably  only speeds of the motors     1 )  Plc CP1EN40S DT1D     2)   hmı : nb7 twb0        3  ınverter s  :  V1000   VZABOP4BAA how can ı use registers numbers of the ınverters so ı need simple program    thanks for  everythings [767]InverterRefresh.zip
  19. High-Speed Counter Input

    Hi, I working on reading impulse from the input. I am using M8000 as a contact, on the coil [C235 K9999] and it is working fine on the lad, but the problem is I need to applicate sth like that in structure ladder but I dont know how. I found function on the image below but it is for FX3U. I know that 2-phase 2-count input use OUT_C(for example EN True| CCoil CC251| CValue K0) and then DMOV(for example EN True| s CN251| d D100), so is there any method to read impulses from the input? .Thanks in advance. PS I have Mitsubishi FX3G series.  
  20. Omron Servo Encoder

    Hello All  I am new to PLC programming , i have a question regarding omron PLC and High speed counters. I am using Cp1H-XA model plc . I connected HSC port 0 with a encoder and i was able to get the speed of the encoder using PRV2 instruction. Now i am trying to connect the second  encoder from the servo motor that i am using to HSC port 1. I am getting the PV signal using PRV instruction . Is there a way to calculate the speed of the servo encoder connected the HSC port 1 using PRV command , since i can't use the PRV2 command for the servo encoder .   Thanks in advance .
  21. Average motor speed

    Hi Guys!   There is a task. I have a motor, and I can monitoring the actual speed. The question is how can I to determine the average speed, if I know just the actual speed. If the speed is zero, it must be ignored. So I have to measure when the motor moves. Anybody have any idea? How can I solve this problem. RSLogix 5000.  Thank you.  
  22. Hi, I have some trouble with a CJ2M-CPU33. My client did a backup to memory card earlier today, and after this we did some changes through remote link. Now the client wanted to restore the previous backup to the PLC and has done so, but the system would not function correctly. After going online on the PLC it seems like the PLC is stuck in "Stop/Programming Mode". When trying to change to "Monitor" or "Run" mode a dialog comes up containing the following message: "Failed to change the operating mode. The operating mode may be still changing in the PLC."  - All the dip switches are set to off after restoring backup - The PLC has been rebooted  - I have downloaded the application again through CX-programmer  - Verified that the PLC is set to start up in "Monitor mode" But nothing helps. The same message comes up when trying to change the operating mode.  Hoping anyone can help to resolve this issue as it is very critical for us and the client. In advance, thanks for any tips or help received. Best regards Stian
  23. Hi , I need to read encoder value on PLC / module QD62E and those value to be seen on the HMI , can anyoune tell me how to do it in to PLC in order that encoder start counting ?
  24. I am trying to connect a Delta ASDA-A2 Servo internal motor encoder to a Delta DVP28SV high speed counter input.  I was successful in connecting the servo to the plc on position mode with an external encoder connected to PLC high speed counter.  Currently having trouble in finding the correct wiring between the servo drive and the plc to count the pulses from the internal motor encoder.  Attached are some figures from the servo drive manual. OA --> X0 is obvious, tried s/s to GND, COM-, VCC and VDD... no result. Any suggestion would be highly appreciated.  
  25. fx3u ENET card, ip change

    hallo all again, is there some way to change external IP (target one) using ENET-502 card without reinit via sending 1 to BFM1600? I would really appreciate it (time savings) but from little what i know it seems impossible :(   thanks in advance