Search the Community
Showing results for tags 'mitsubishi 500m control'.
Found 435 results
-
hello dear team, im trying to make a back up for some FR-E700 with the FR CONFIGURATOR SW3 but when i start the communication with the USB cable the software cant recognize any port by the way im using windows 10 in my laptop and when i check the devices administrator it doesnt shows in USB ports the drive info just in other devices and in details shows: "USB device was not migrated" does anyone know what can i do?
-
Hi, I am trying to establish communication between master and slave through modbus rtu rs485. But I am experiencing error code 7378h. I already tried to make the values of Request Interval Timer from 100 to 200 and Broadcast Delat Value from 50 to 100. But the error still persist. Any tips how to solve this issue? There is no error on the slave evices.
-
Missing components in module list when configuring Mitsubishi CC-link
kimdinhthaibk posted a topic in Mitsubishi
Hello everyone! I've installed GX works 3 according to the instructions in "https://plc4me.com/gx-works3-v1-308q-mitsubishi-full-real-100/". I don't get any errors, I can run the PLC and simulate completely OK. In the communication test, when the configuration is missing some components in the module list: Input, output, I / O module,... (https://ibb.co/ZVMcmQn) I hope you can answer for me? -
Dear members , 1.)I have sensor which i read it from analog input (0-10v) specific value and i will pas it via analog output (0-10) to controll VFD for air spped controll . so i'd like to keep specific value for example i will set value 260 , so if analog read les that this value than analog output increase voltage to analog output , if analog read more than this value output decrease voltage . 2.) i have Digital to analog register D8096 which 0 value means 0 volt and 4090 means 10v , so when i need to pas value to i make MOV D200 D8090 , is there a posibility to limit write value to D200 to not pass 4090 ?
-
Hi Guys, I need help to set up modbus tcp/ip parameter for Q03UDVCPU, i want to use the predifined protocol and built in ethernet port. do you guys have some usefull references how to setup modbus tcp/ip, or is there any example program from mitsubishi? Thanks
-
Designed a SCADA System using VB.NET. Everything working fine but coming to performance getting 2 to 3 seconds delay. Using FX3U32m Plc with ENET Module for Data reading and writing. I am having 200 addresses to read. Using MX Component as communication interface between PLC and SCADA. Is there any alternative or solution for this problem. Using one timer to read all data and update properties based on received data. Thank you..
-
Please help how to set the language I'm using Windows 10, the comment and program origin is from China. Im using GX Developer sorry I dont know why I cannot attached a photo.
-
Hello Everyone. We have Schneider TM241 PLC Along with Citect SCADA System at 100MWp Solar Power Plant to monitor and control various equipments like Inverters, Switch-Yard, MFMs, Weather Monitoring Systems etc... Government Authority here asked every solar plant to control the generation as per the instructions by Load Dispatch Center, for that we need to implement logic to control Generation as per requirement. For that we are controlling generation from inverters by giving them generation setpoints calculated by PLC using PID function. But we are facing one problem while using PID. (FB_PID of Toolbox Library) Suppose we need to generate only 60MW out of 100MW. So we set PID setpoint to 60MW and according to that we get PID output and according to that PID output value we provide generation setpoint to every inverters. This system works very fine until the clouds comes into the picture. Now suppose Setpoint of PID is 60MW and PV is also near about 60MW, and suddenly large cloud comes over plant and block solar radiation. In this case generation comes down to 10MWp(or any value below 60MW), So output of PID will Increase and keep increasing and settle at the Maximum value. but without solar radiation generation value stays very down then Setpoint. Now suddenly Cloud moves and again solar radiation increase, but the PID output is maximum at that time so, Suddenly Generation goes from 10MW to near about maximum capacity (100MW) instead of 60MW, and then it will slowly comes down to 60MW. We need to rectify this generation shoot up when cloud moves. Anyone have idea how can we solve this problem or anyone have programmed PID in this kind of situation. Is there any function block available to do this correctly like function block of PID with two Reference or something like that... We are using TM241 which is CoDeSys based PLC.
-
Hello Members. I am trying to read Counter values from FX3U PLC using VB.net AxactUtlType Library. But i am not getting those values from PLC. I am getting Memory and Analog data but not Getting Timer and Counter Data How we read that data? Thanks in advance.
-
Hi all, I am not a PLC expert but can find my way within the program and would like to develop much more. For work (We sell industrial bandsaws) we have purchased a Posital Fraba wire encoder, and we would like to hook it up to our Mitsubishi FX3G PLCs to measure at what height the saw bow of the bandsaw is at that moment. Unfortunately I have little experience with connecting these things, as other encoders used in our machines are pre-installed by our factory. Below is described what functions the wires have. What I thought was the following: Pin 1 goes to an input of the PLC Pin 2 goes to + (or 24V) Pin 3 doesn't go to "Ground" as they describe, but instead to - (or 0V), which is technically ground Pin 4 and 5 we don't use, correct me if I am wrong. The saw bow goes up and down only, and I thought we don't need to use these wires. I connected it like this, connected wire 1 to X0 on PLC and just to test I made the program read: M8000 ------------------------------ C235 k99999 But the value stays 0, whether I pull the wire or not. So something is wrong, but what, I really can't figure out. Hope someone can help!
-
Hello everyone, As the title suggests I am trying to display on a GOT1000 the real time frequency that the inverter is running at. I have attached my CC-Link settings and the associated programming as well. I tried using the example program from Mitsubishi but I got lost. From my understanding I should be seeing the output frequency in W3C4 however, I am not receiving any data. Any help would be appreciated.
-
Dear sir, Good day. I using SFRD instruction to read all the value stored when the sensor trigger. When the SFRD instruction is end(whe the word device number goes to 0), it will move the value to my store value and change my store value. May I know how to stop it to overwrite my store value?
-
I cannot use register D128 - 255 in the program with the Block function
phucPLC posted a topic in Mitsubishi
Hi every one ! I cannot use register D128 - D255 in the program when I create a program that uses the Block function in the PLC mitsubishi FX1S, it gives an error : A device of the device range set in the device/label automatic-assign setting or a device which cannot be used due to system reservation is being used.Help me,Thanks ! -
Hello everyone, I have a Kinetix 6000 CIP drive (unwind) and I need to control its speed by a PID controller. I have everything working except the MCD instruction doesn't pick up on the PID output value change. It changes the JOG speed, which I use to control the unwind, if I set the speed manually, which is slow. The PID changes the speed almost continuously. Any suggestions are welcome. This is how I'm attempting to control the speed: A1_r_JogSpeed = PID output value Thank you
-
Hi Mr.PLC Members, I have Mitsubishi FX16MT unit, I'm trying to transfer programs to it using melsec medoc version 1.64b but I can't I'm receiving error "no reply from PLC system",I'm using 25 pin to 9 pin cable and I tried also to connect it with usb to serial cable but the same error appeared my setup: PLC system FX Bit rate 300 word length 7 parity Even stopbits 2 "windows XP" Attached are photo of my unit with my cables and the error of the program
-
Hi Guys, Can you help me out with this question The servo motor connected to axis-1 rotates in the forward direction when the M1 button is pressed, and in the reverse direction when the M2 button is pressed. When two buttons are pressed at the same time, the engine stops after 5 seconds. Write the program that performs this process with GX Works3.
-
Hello, I was wondering if any of you have experience translating comments. To be more specific, I have been tasked with translating all of the comments in my plant from japanese to english. We have many different series of PLCs, but they are all mitsubishi, and I will be using GXWorks 2 for 99% of them. I had the idea of writing the comments to a CSV file, Translate them there, and then just read them from CSV back into the project. I have tried numerous methods, but it seems the CSV loses format and isnt able to be read back into GXWorks. Some of these comment files have almost 10,000 comments. Do any of you have any suggestions on the best way to translate these comments over, in a more automated way than manually one-by-one. Thanks in advance for any support you can provide!
-
Hi All First ever post so forgive me if I do anything wrong. My customer has given me an FX5Uc PLC and a Delta DOP-B03S211 HMI. Comms need to be via serial. Ethernet not an option. I have configured the HMI as the Delta DOP datasheet(see attached) I have configured the PLC as: - MC-Protocol - 19200,8,1,Odd I however get an HMI error: - ########################################## COM 1 STATION 0: COMMUNICATION ERROR 3. READ ERROR No Response from Controller ######################################### I have created a simple page on the HMI consisting of a push button (M reg) and a numeric display (D reg). When pressing the push button I can see the change in the PLC. (Transmission good) Any change of the D reg in the PLC is not reflected on the HMI. Confirms the message. I have tried all combinations of settings on both side but no joy. The PLC seems to be happy as it receives and transmits ok with no errors. Can any one see what I am doing wrong? DELTA_IA-HMI_Mitsubishi FX5U_CM_ENG_20170728.pdf
-
Hi all! We have a problem with a Mitsubishi system. After switch off the machine in home position and back on, it resets the servo encoder value to 0. I checked the servo parameters, and the Absolute encoder is enabled, the ext. battery is ok and no zero reseting in the program ( I think...). Is there a parameter I should check or some setting in the intelligent module? The system consists Q01CPU, QD77MS2 im., J4 200B amp with 6v battery, and HG-SR152 motor.
-
So I'm having trouble writing a FBD within my current program for a slitting line. I need to keep a constant tension on my web as it is being recoiled onto our recoiler. I wrote a simple program using a sensor to read the growing rate of the coil to get a radius and I have feedback on my torque on the recoiler motor. The simplest math for this application without getting into anything too fancy should be Tension(lbs)= Torque(ftlbs)/coil radius. only problem is when its less than a foot then my calculation is thrown off and it actually shows tension goes up until it reaches the one foot mark then it seems to scale correctly. Do I need to scale something else? Any help on this would be appreciated.
-
Hello There I need to set up communication PLC to PLC ( R08CPU to Fx5CPU) but i dont have the modbus library for the R08 Does anyone have the library? or where can i get it? thank you.
-
Hello, I need to connect remotely to an OPC Server DA. In my PC I have installed several OPC Clients but when I try to connect to the server (therefore located on another machine) I get an "access denied" error. How can I authorize the exchange of information between the 2 machines? Thanks
-
Hi all. I've set up the analog modules and I've set devices within the HMI to move the value of d to the special registers for process alarm limits but whenever the plc is reset I'm losing the value. Have I missed a storing trigger or something?
-
i have a question about SFC , if the step is active then processor execute code inside this step and writes on outputs true or false , then when the step deactivated the processor won't execute the code inside the step and won't write true or false on outputs. this means if output Y1 becomes true in activated step then it will remain true after deactivation , right ? in this picture if S41 is active , then M77 becomes true , then S43 becomes active , and S41 isn't active , then M77 will remain true and the processor won't execute S41 , or will becomes false then processor stops executing S41 .
-
i want to know the role of M2 is to enable the comparison function or it's anded with the output of the function. in another words if M2 is true and the output of the function is true then M3 is true, but what if M2 becoms false if it's anded with the output of the function then M3 is false , but if M2 stops the execution of the function M3 will remain true, so i need to know if it controllers the execution or it's just anded.