Search the Community

Showing results for tags 'MicroLogix 1000'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 72 results

  1. communication

    i want to communicate ml1400/compact logix L24ER to simatic s7200 via ethernet.Please help me with it i am new to it and dont know how to do it.
  2. SLC 500 and SMC Ex260

    I'm trying to connect a SMC EX-260 to a Allen Bradley Micrologix 1400 PLC so  I can run some valves with it. However, RsLogix 500 doesn't allow me to just setup a generic ethernet device like I would on RsLogix 5000. Is there a way I can communicate these devices together so I can use the SMC Valve system with my Micrologix?
  3. Square Wave Problem With Micrologix

    Hello all, this is my first post. I am using an AB Micrologix 1400 (1766-L32BXB Ser C FW 21). I was trying to generate a pulse train using the PTO instruction. I have modified PTOX funct. file. The ladder is just a simple XIO followed by PTO, (The Quick Start ladder from 1766-RM001). When I looked at the output waveform on my oscilloscope, I noticed that it wasn't a square wave. I decided to run it at several different frequencies to see how the wave form would change. At 10Hz i got a square wave. As I increased the frequency the falling edge became sloped and almost horizontal. Is this how the output should behave? The data sheet indicates a max frequency of 100kHz, but at frequencies over 150 Hz. The wave form looks like the output of SMPS. 
  4. Hi all, I have my own driver to communicate with a MicroLogix 1400. Please refer to the attached screenshot from Wireshark. 10.10.21.10 is my driver's host, and 192.168.1.192 is the ML1400. The startup sequence to establish a connection & session with the PLC is correct I believe: - In the grey highlight, client requests a connection to .192 via SYN and this is ack'd - A session is registered, and forward open is successful - There's a lot of stuff in green simply because I've also got an HTTP browser session open to the PLC to monitor its session table - In between, spaced 8 seconds apart, are my two attempts to keep the connection alive by sending a List Identity request (as a ping, if you like). These are highlighted in pale blue. - However, 16.5 seconds from the start of the grey highlight, and 16.4 seconds after sequence=115 ack=99, the controller sends back a [RST, ACK] and a callback from my socket code tells me that the session has been dropped. The connection timeout for the PLC is configured as either 30 or 60 seconds, so I don't see how that's relevant here when the reset is happening only 17 seconds after it was established ? However, presumably the PLC doesn't see the application-level "List Identity" request as a valid means of keeping the connection alive. What is the correct mechanism to use that the PLC will accept as a keep-alive ?
  5. Hi there, As a software engineer, but a newbie to the Allen-Bradley world, sorry if this question doesn't make sense. I'm enhancing an existing driver by trying to add the ability to read/write structured and array data types - rather than just the elementary data types it supports right now. This following question is only in the context of SLC/500 & MicroLogix 1400. And I'm currently working on a Counter as a test case, but any solution obviously needs to take into account other structured (and array) data types. One of the requirements is that the user should be able to select a specific atomic item within a parent structure/array that they want to read/write. So, using the Counter as an example, they might want to define a field which holds just the value of the accumulator. I know that I can achieve this with a CIP command. I specify file type 87 for counter, file number as 5 (my test example happens to be the standard C5 data file of counters), and element is 0 (for the first counter in C5). Bit number is irrelevant so remains as zero. I ask CIP to return me 2 bytes of data (to hold just the accumulator word). Finally, I tell CIP that I want sub-element 2 (because the accumulator is Word 2 of the whole structure). Sure enough, the CIP response gives me exactly the 2-byte accumulator value I was expecting, nothing more, nothing less. Success. My question is this: I knew I had to specify the sub-element as 2; this happens to work for a Counter because of the way it is structured as 3 words. However, it implies that the value I specify for sub-element is ALWAYS measured in units of 16-bit words. Is this a universal truth (i.e. works for other structured types too ?), or does the size of a sub-element depend on other factors, such as the file type ?   Thank you in anticipation.
  6. EEPROM PLC's

    I thought only PLC5's had EEPROM, but I was told MicroLogix PLC's also have an EEPROM that need to be burned to... What are all the PLC's that have EEPROM and require an EEPROM burn to prevent the program from being wiped in a power cycle?
  7. mitsubishi nexgenie plc target settings View File This target setting files are used with codesys software for programming mitsubishi nexgeine PLC series,    Submitter lionheart86 Submitted 01/18/17 Category Demo Software
  8. My project is to read an RFID tag (ascii) with a Micrologix 1400, send the string to a PC using Ethernet/IP, lookup and compare in an Excel spreadsheet, and send back data (probably an integer) for the plc to use to control direction. I have to scan and compare an RFID tag to a list of 1400 possible part numbers, at different locations (more than 1 plc). I want the several PLCs to go to a single PC to make it easy to update when changes occur (on a weekly basis). Has anyone done anything like this? I'm assuming there will have to be some kind of vb or c+ application involved.   Thanks,  CK
  9. Hi All, Am trying to communicate and make In-Sight bar code reader to trigger through MicroLogix 1100 with RSLogix 500.  Does any have any info as to the steps to follow. Most of the info I saw and have tried were for SLC processor In fact, I created the String file ST10:0  for the target device as was mentioned in one of the posts but when I complied it there was error saying that St10:0 was not supported by the module. Please see attached file. Any insight will be appreciated  
  10. I know nothing about HMI's or Crimson software.  I'm in I.T. and we had to change the third octet in the IP address and gateway on all devices at our warehouse.  I extracted the file on one HMI, changed the ethernet info, and clicked send.  That HMI that runs a carpet machine works perfectly.  I went to the second carpet machine.  Extracted the file changed it's ethernet info, clicked send.  It came back with all ---- (dash's) instead of zeros, the carpet machine won't work.  I kept messing with the file trying different things, and inadvertently saved over the original extracted file!!!!!  So I thought I'd extract the file from the working carpet machine and loaded it on the second carpet machine.  I get the same issue, all ---- (dash's) on the HMI and you push any of the buttons on the front of the HMI and nothing works.  These are Allen Bradley MicroLogix 1500 running Crimson 2.0 HELP I don't know how to resolve this issue.  I would have thought both HMI's would have been the same!  HMI all dashes.eml HMI all dashes2.eml
  11. MicroLogix 1100 IP Addressing

    I have a micrologix 1100 PLC as well as a weintek HMI all connected through a network switch for them to communicate between each other, however I'm having an issue where the Micrologix Controller will not retain its IP address once I set it through Allen Bradleys BootP tool. I can set it through the tool and then go into RSlogix 500 and communicate with it and all that, but once the controller is turned off the IP address goes back to its factory setting of not showing an IP at all. Any suggestions/ ideas as to what I'm doing wrong?
  12. Hello good day ! I have a problem with a Panel View 1000 plus, I accidentally connected this device to 240V and the rv2 of the circuitry has burned. I am not sure what reference this device is but I need to change it as soon as possible, I would appreciate it if you could help me! Thank you
  13. Stepper Motor Control

    can anybody Know how to control stepper motor using PLC
  14. Does anyone have the User Manual for the Modicon Plus 1000? Trying to program a "ReadOut" template to show the value of a PLC-5 Integer file. Keeps saying that the "N" is not a valid file type. I've done this on the Cutler-Hammer PM1000. The Modicon will not allow the C-H program to download, says it's not a C-H product. Thankx in advance for any help
  15. Hey, I have a 1763 L16BBB...when I plug the 1762IF20F2 analog card in, I get a 0189h error code. Any help would be appreciated. Currently looking at doing a bootp on the plc to get online...no ip
  16. Have a micrologix 1200R 1762-L40BWAR.  If anyone could help with providing the following information: Need a communication port with single receptacle that will mount through the door of electrical enclosure and then the communication cable (6 to 10') that will go from the com. port to the micrologix. Thanks
  17. Does anyone have an example piece of ladder logic, created on a Micrologix 1200, using ASCII to READ and Write to a serial device?  I am building a ladder on a Micrologix 1200 that will send data to an old CNC once a certain ASCII instruction is received on the PLC.  For example, when the machine spits out an ASCII "1", the PLC will see the "1" and send out a three digit number depending on a sequence of discrete inputs.   Thank you,
  18. Hello I would like to first let everyone know I am new to the world of troubleshooting or programming plc's . What we have is a SLC500 system that is connected to a Panelview 1000 HMI via the DH+ network. The issue we have is the panelview displays a gate that is suppose to be closed at as gate fault. When i connect to the plc the ladder rung shows that the gate is closed. To show various positions of the gate the programmer used N13:70 as gate opened and N13:71 as gate faulted and N13:72 as gate closed. When i checked the logic it showed the bit N13:72 as engaged or true if you will. This logic is in the ladder rung that is labeled PV Status which i take is the status the HMI reads so my question is why does it show GF when it should be reading GC. Ive searched all through the logic and it doesnt appear to be wrong here is the logic the best I can simulate it  ladder 6 rung  53  instruction is  XIC O:13.0/11 and OTE N13:76/0 (Gate Open ) and the branch is XIC I:5.0/11and OTE N13:76/1 (Gate Fault) next branch is XIC N13:3/11 and OTE N13:76/2 (Gate Closed which this section is green or highlighted or true which ever you like) when i looked at the input XIC N13:3/11 this is what I found is that this XIC is on ladder four rung10 and has the following XIC T4:154/DN and branchoff that is XIC I:5.0/11(gate opened)XIC I:6.0/11(gate closed) which these two inputs are false or not lighted the output is OTL N13:3/11 and it is true which makes the previous rung true showing the gate closed. So why is the panelview showing the wrong position. I even went as far as resetting the HMI and the PLC so if anyone has a helpful hint I would greatly appreciate it.
  19. Hello, I'm new to PLC Programming, with just a simple course about the basics. I've got a micrologix 1400 PLC which seems to have had its program wiped when the battery was replaced. I've had the company that supplied the machine it runs send me the program for the PLC. However, I don't have any software to communicate with it, and download the program to the PLC. I was hoping some one here could help me out and direct me towards what I will need to do to get the new program installed on the PLC. Thank you 
  20. Hello I have a scenario that's been bugging me for some time now. The scenario consists of a Micrologix 1400 that I need to control it's output from modbus/tcp. In detail what I really need is to be able to manipulate the O0:0 through modbus/tcp. The PLC would be the master and I would be the slave that triggers the connection to the master. I'm using a Modbus-Client on my PC and that should be the slave. Any idea as to how I can manage that? Currently I can send data to the master but everything is "stored" on B10 and I have no idea how I could write directly on O0. Thanks a bunch guys. PS: I'm borderline noob. 
  21. Hi my problem may have a simple solution but i cant work it out. I need to use the Divide function but it wont let me use a decimal point in either Source A or Source B. Is there a way to use a decimal point in Logix 500 Math instructions? Im using an AB Micrologix 1400 PLC. Can you only use math instructions with whole numbers? is there a way around this? Thanks James
  22. Hi my problem may have a simple solution but i cant work it out. I need to use the Divide function but it wont let me use a decimal point in either Source A or Source B. Is there a way to use a decimal point in Logix 500 Math instructions? Im using an AB Micrologix 1400 PLC. Can you only use math instructions with whole numbers? is there a way around this? Thanks James
  23. Communication

    good evening. Someone can give tips on how to configure and physical the application with the following items: Advanced Interface Converters (AIC +), PanelView800 2711R-T7T A and MicroLogix 1500 Programmable Controllers My doubts are about the configuration of the communication, and I have doubts about the physical environment and protocol to be used.  
  24. Does anyone know a way to convert GOT 2000 screens to a GOT 1000? 
  25. Hello :I'm the creator of an Android HMI app,  I recently added Ethernet/IP connectivity with MicroLogix and SLC AB PLCs, but I have only been able to test it with a MicroLogix 1100.I'm really not sure if it works with SLC or with other MicroLogix models.If someone could try it, I would appreciate it. To access the test, from the Android device, open this https://play.google.com/apps/testing/com.suppanel.suppanel on the web browser and install the Beta version.On the application you have to open the "EIP MicroLogic SLC Test" panel that contains some instructions. Thank you very much !