Search the Community

Showing results for tags 'difference between fx3g and fx3ge'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 42 results

  1. fx3g plc pls bit

    hello, I have problem with fx3g series PLC. I attached ladder program fragment.When I set momentary bit M1 don't send PLS M4, but if i set momentary M2 program running well. Why is it?
  2. Fx3g Binary bit Output

    Hello, Need your advice. I am trying decimal number convert to binary and do output. for example If inside  D90 I have 11 decimal number then for me need active output Y0, Y1 and Y3. I tried make this code below, but it is not work, don't active output . Maybe fx3g PLC have function how need to do it?
  3. HI Everyone,  Recently i have bought a plc fx3ge and gt2000 hmi .the problem is that whenever i use a device address d280.b1 in hmi .i am not able to use the same address in gx works for plc (LD D280.1).can anyone help me with this problem.   
  4. We are communicating FX3GE PLC with Vijeo Citect SCADA. We tried various protocols such as MelsecNET, MelsecFX2N, Melsec1, etc. If you know how please help.
  5. Hi. I'm hoping someone can give me an answer on this problem I'm having with a FX3GE PLC. I am trying to get a FX3GE plc to communicate to a drive over RS485 using a FX3G-485-BD card. In GXworks2. But am having no luck.  I have tried changing the PLC communication settings in PLC parameters between CH1 and CH2, But am unable to get any communication working on the front port. I have also tested with a FX3G-232-BD RS232 card and have the same problems. There is no activity on the SD RD led's and no data being sent. If I put the FX3G-485-BD card in a FX3G or FX3S PLC I have running the same code it works fine. So the problem I'm having is with the FX3GE PLC Please can someone tell me what the difference is with the front Communication port on the FX3G and the FX3GE. And how I can get the FX3G-485-BD card working on the FX3GE PLC. Thanks
  6. Hi there! I need to set up a communication link between an FX3GE PLC and a Melfa RV-2F-D robot with a CR750-D controller. Can I use the PLC's built in ethernet port for this? Is there a native driver for this (i.e. to read a register from the PLC into the robot controller)? Or should I use some kind of a no protocol communication? We also have a GT1455 in the setup and had in the past a solution where the robot was talking to an FX3U trough the HMI, but there was a lag in the communication which I would like to avoid. I am new to Mitsubishi so please bear with me. Thanks!
  7. Program Notes & Comments

    I used to use the Old Dos based MEDOC very many, many, years. I havn,t programmed for years now. We have GX Works 2 at work, and I am practicing programming an FX 3G - 40M to try and keep my hand in. Allthough I can write and read the program ok, the PLC keeps saying that it has no memory for the comments. Apparently the memory has to be set on the PLC. Any advice or information links will be appreciated
  8. FX3G-2AD-BD Store Peak Value

    Good day, I'm new to this forum and to mitsubishi PLC but was hoping for some assistance with a programming issue. I have been through the hardware and programming manuals without luck for this issue. Hardware: FX3G-60mt FX3G-2AD-BE Settings: Structured ladder/FBD Current input mode on: M8260 (first board, first input)   What I need to do is to record the peak value over a cylinder stroke period. The hardware manual explains how to average the value using averaging time, however I basically need to peak hold and send that to a D register for go no-go compare.    Process as follows: Contact closed, monitor D8260, contact open, move peak value from D8260 during monitor duration to D205.    Thanks in advance for any assistance. -Swervomotor  
  9. Hi guys! As the title explains, i wanna move a value to 210 -> 220... is there a function for that or do i have to make a MOV for every single dataregistry (look at picture)? Its an mitsubishi FX3GE PLC programmed in GxWorks2. Br, Jim  
  10. Hello I have PLC FX3GE-24MR/ES with FX3G-485-BD board  and rail350 electric meter I want to ask you. Is it possible Modbus RTU Communication between PLC FX3GE-24MR/ES and rail350 electric meter? If yes, then maybe you give advice how need to read data of ladder languages
  11. FX3G Hardware configuration

    Dear All, I really appreciate in advance your help in this problem. This is my first project with Mitsubishi PLC. I am using GX Works 2 for programming. Hardware is FX2G-24M base unit + FX2n-16EX extension module. I already started a new program and download simple rung on PLC, put PLC in run mode, test it and working properly. the problem is that I do not know what is the address of inputs of extension module. I tried to complete and use X016 but no response in PLC. kindly advise what shall I do. Thanks
  12. Hello, Can a password protected PLC be updated with a help a memory cassette? The documentation states that it is not possible. But if the memory cassette is protected with the same keyword? Thank you.
  13. Dear Sir, I want to read data (Digital Input say X0 (Local PLC) and after some additional logic i want write to Y0 (Remote FX3GE PLC on same network) from one Mitsubishi FX3GE and Write to another FX3GE on the same network. Master PLC IP Address Slave PLC IP Address Atif
  14. Hello again! This time I have issues with PWM Block in GX Works 2. Im using it to control output for Rudder Machine. S1 Time is Pulse time S2 is response wait time. I follow the rules that S1, S2 cannot be zero, N2<N1. I compile and run the program. Everything is ok, program works perfectly. Sometimes when I modify instructions in PWM Rung - i get an error No. Result Data Name Class Content Error Code 4 ERROR POU_01 Program compile Invalid list code 'PWM D992 D990 M1524'(Ladder Block No.7) F0161 I pinpoint that I use 2 block of PWM one for each side. They cannot work at the same time. See attachments with code Thank you in advance!
  15. can anyone please provide me "keithley Model 7009-5 Shielded RS-232 Cable configuration." ? for communication with fx-3ge plc to nanovoltmeter 2182 controller.