Search the Community

Showing results for tags 'read'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 12 results

  1. Hello everyone! Is there possibility to read words e.g. Name of alarm from the csv file or another file and save it in the PLC memory for further processing? It would be the best if the solution will matches to FX5 and IQ-R/F but it can be also for any of them. Thanks for help :)
  2. Hi,     I'm trying to communicate Omron CP1E unit with PC via serial port using hostlink protocol.  I need to read the Timer/Counter SV value and write the timer/counter SV values to the PLC.  I'm able to use other C mode commands (like RC (timer/counter PV read), WC (timer/counter PV write) etc.) but when I give the command for Timer/Counter SV Read 1 which is R#, I get the response as IC (Undefined Command).   How do I write or read the timer SV Values?  Example command and response : @00R#TIMH001028*  (TIMH is the high speed timer, 0010 is the timer number and 28 is the FCS) Response: @00IC4A* Is is that CP1E doesn't support these commands? If so what is the equivalent command that I should send inorder to perform this? Please help.  
  3. I am using GX Works Version 1.493P After selecting Online->Monitor -> Monitor Mode ... and doing some online debugging... I find my projects stuck in read-only mode. Even restarting the computer does not make the project editable again. Any help will be greatly appreciated.
  4. Structured Ladder

    Need Help! I uploaded structured ladder program into FX3S PLC. But When I try to read it from PLC it says the program cannot be opened. 
  5. Hello Everyone, I have a Omron CJ2M PLC, and I have configured the Ethernet/IP port of this PLC to communicate over ethernet connection. I want to read/write the DM, HR memory areas of Omron PLC (CJ2M) using eip protocol communication. Is there any protocol specification which explains the telegram structure to be sent over ethernet to be able to read/write the values in omron plc over EIP? I want to know the command structure which can be sent to PLC and PLC will respond with the proper response. 
  6. Can Anyone Come Up with the Screen Shots or a video link of procedure for Displaying Real Time Sinusoidal Waveforms From Satec MFM ON GE FANUC?? I have PACsystem RX3i via Serial Communications Module-IC695CMM002 
  7. master k 250

    How to read korea plc master k 250 since it can not read by using KGwin software .thanks
  8. Dear, i am doing one project on Omron PLC with VB.net.  i am using Ethernet communication  with  VB to PLC but i am unable to show analog value on VB page please guide me how to get data of analog value in vb and show in VB.net for DI/DO i am using CIO &H0  forreading   and  &H1 for write but for analog value how i will show on VB.net.
  9. Rslogix 5000

    I am unable to read FBD program in RSlogix 5000.It says editor not downloaded.I m able to see ladder logic programs.
  10. Hi,  i want to read real time and date in simulation mode. How can i do this in Unity pro? Thanks for helping
  11. Good morning, I'm having an odd issue with CX Programmer and have hit a wall. I'm trying to upload a previous version of a program to an existing PLC (CS1G-H CPU42) and I keep getting the following error when I compile while online: "The read protection properties which are not supported by the connecting target PLC are set. Check the unit version of the PLC." This prevents the program from being uploaded. I have a first revision CS1, manufacture in 2005 from what I can tell. This exact program has been uploaded previously, but a modified version replaced it recently and I need to go back to the older version. Things I have tried so far. without success: - Removed UM Protection - Made sure Task protection is off for all tasks - Check DIP Switch #1, which is write protection, and made sure it is off - Used "Remove Password" and "Release access" functions from the PLC/Protection menu - Used the auto-verification to confirm the configured PLC is correct - Reuploaded a full backup of H & D memory, from the older program I am able to compile the program when offline, but it chokes when online. I am connecting to the PLC via a serial cable. I haven't found any help from the CX Programmer help, or the CS1 programming and operation manual. This error message is nowhere to be found. Anyone has a clue ? I'm at a loss right now. Thank you !
  12. Hello All, I want to read data from a Control Logix PLC, into a PLC5/60, using Ethernet and a MSG instruction in the PLC5. When verifying the MSG instruction in the PLC5, I get an error message. "Target Address in invalid". Once I figure out how to do this I need to replicate it in another PLC5. Scope is to read the status of 4 paint pumps controlled by the CLX. If any of the 4 stop, the PLC5 needs to know, because it is controlling the paint application equipment. Source data resides in a Control Logix 1756-L63. The tag is INT type, 4 elements long, and the name is PUMP_STS_B2. The IP address of the CLX is 4.2.6.230. There are 2 ENBT cards, one in slot 1, and the other in slot 3. 4.2.6.230 is slot 3. PLC2,5 / SLC Mapping has been created in the CLX. File=421 Name PUMP_STS_B1 and File=422 Name Pump_STS_B2. The file mappings represent a binary file created in each of the PLC5's B421:0~4 in Booth 1, and B422:0~4 in Booth 2. The PLC5/60 is Enhanced series E model using the Ethernet side card. The IP address of the PLC5 is 3.26.5.61. I also created MG file types in each of the PLC5/60. MG420:0~19 in each processor. This was necessary to use the MSG instruction in the PLC5. I have searched the forums for examples of how to do this with no solid results. I am trying to follow the best practices of reading the data into my PLC so anyone who follows can tell where it is coming from. While the IP addresses are not closely related they should be able to communicate. I say this because all of our PC's are on the 4.2.6.XXX network on a 255.255.252.0 sub net and we have no issue communicating with the 3.26.5.61 IP address. Any help and advice would be greatly appreciated. Regards, Mike Carter