Search the Community

Showing results for tags 'gt2310 communication problem'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 135 results

  1. 2 PLC WITH ONE HMI

    hi.   Can i connect two plc mitsubishi with one hmi . is so .. can u guide the connection between them . Hmi is of weintek.  one plc is FX1S and the second is FX2n
  2. hy everyone.. I want to communication inverter SJ700 to hmi mitsubishi GS2017 for read an code error in interface HMI? is it possible to communication between them?
  3. Hi everybody, I have a GT2310 communicating with the Mitsubishi F800 VFD. I am using the Freqrol 800 communication driver, connected to the RS-485 terminals of the GOT and on the F800. The comm settings are the same on both devices. I also tried to use the “auto negotiation” setup. I have communication between the two devices. I can read and write to F800 registers.   Anyways, The GT designer diagnostics is complaining about a communication error in the system alarms. The error can be reset but it will appear again.   This also happened when I created a new, empty project where just the communication was setup as described above.   Did anyone experienced the problem and how to troubleshoot / solve this?   Best regards
  4. Hello I have a problem with dl-ep1 ethernet modul. I connected the module to a IL-1000 sensor amplifier. There is some problem with the communication. How should I adjust ? I made some pic about the trouble. The sensor is a IL-600 laser distance sensor. I dont know yet how can I get the actual value.  Anybody knows how to set this modul ? If I think correctly after the right setting, if I check the sensor output:0 then, I can see the actual value of the IL-600 sensor. But unfortunatelly this part also not so clear for me, because I can connect about 15 sensor this ethernet modul.  Thank you so much if anybody help.
  5. HI All, i am new to this site, if anyone can help me out for below topic. I am trying to communicate E1101 hmi with Q06UDEH PLC but its giving me continuous communication error. i am using e designer for hmi and gxworks2 for programming. i am attaching the communication screen shots for both,i am quite stuck at this point as i have used all options still not able to solve it. if anyone can help me out with this,help is much appreciated. Thanks in advance  
  6. CP1L-EL TCP/IP with VideoJet Printer

    Hello, My previous topic was want to establish communication CP1E --> Videojeet Printer using RS232 serial cable. this project test SUCCESS. by the way distance from printer and PLC was very far almost 500meter. so printer technical team request to use tcp communication using cat5e cable. Problem: 1. I'm using TCP communication protocol that need me to have open,send,receive,close port. 2. Communication testing with PC Hyper Terminal --> OK but HT need in waiting call mode, i don't know why. 3. Using printer no result show. how i'm suppose to know communication already establish? 4. Communication setting on PLC Setting-Built in Enthernet need to add other communication device.? here i'm share some programs to give more understanding. Thanksm TCP with printer.cxp
  7. error HMI in proface GP477R-EG11

    Hi everybody, can someone help me, to solve my problem with commnunication error. ??? I have plc Q03UDVCPU using module QJ71C24N and HMI proface GP477R-EG11  using RS 422.. I had connected them but still error.. Side hmi that im connect is 10 RDA to SDA 11 SDA to RDB 15 SDB to RDB 16 RDB to SDB 7 SG to SG  
  8. Siprotec Relay 7sj62

    I have 24 Siemens Siprotec relay(7sj62) which i want to communicate with Scadapack 330E (Schneider) on 103 Protocol. but every time I try to communicate it shows Slave device is failed to communicate. trying to communicating via serial (RS-485). What should i do..?? or do i need to communicate it with Siemens PLC..?? If so which PLC should use..??
  9. i am new in indusoft web studio. i am facing a problem about communication of indusoft with plc.   i am communicating with plc through fx2n-422-bd card.   can some one guide me the steps of communication.  he/she will be a life saver.. as i am  in a deep trouble
  10. HMI and PLC Communication problem

    hi there. .. i am new to plc programming.. Right now i am having problem related to communication between hmi and plc.. i have HMI WEintek 6070ip and plc mitsubishi FX2n.. i have written a program in gx developer . and communicate it with EASY Builder for HMI. so for now plc is communicating with my program written for hmi on pc. but when i downlaod to hmi and connect plc cable to hmi then hmi shows no plc communication. i am having a problem for communication between hmi and plc. any help will be a life saver. thanks in advance
  11. Graphic Operational Controller

    Please give me the steps how to communicate GOC with Laptop using Ethernet and serial port I have using Codesys for Programming
  12. Greeatings .   I have modicon TSX premium plc (TSX P57103) I have problem i cant connect to my plc. I have tsx pcx 1031 cable and have com port on one PC and on the second i have connector to this cable with usb. when i try xway test i have problem , the request is always 0 . Can someone help me ???
  13. CP1E RS232 communication to my weighing

    hello, i want to connect CP1E to EK300i (weighing scale) with RS232 communication. i attach file of datasheet ek300i, wiring CP1E to ek300i and my cx programmer. if i push send data on ek300i, com LED indicator in CP1E is on. and i dont know why my cx programmer can't change data of memory with data from ek300i? what should i do?   ek300i.pdf CP1E to EK300i rs232 communication (belum dicoba).cxp CP1E to EK300i rs232 communication (belum dicoba).opt wiring rs232 ek300i to CP1E (belum dicoba).txt
  14. Hello every one. I have three FX3U plc needed to be communicate over a wireless network. I'm using serial adapter FX3U-485ADP. I got E-byte data trans reciver E-30 for wireless communication. Now need help to setup the whole thing. Previously the PLC's serial connectors were connected through a flexible bus but when the platforms are running fast there is interruption in the  communication. So we want those PLC's to be connected over wifi.  Thanks in Advance 
  15. Anyone know any free libary to communication with FX3u-enet-adp, please help me ? Note: I've used mx Component , it work very well but it is too expensive and I dont even know it can work in windows server 2012/2016 or not.  one more question, Is there otherway to make program run in other computer without install mx compoment, it is very huge to install in every client computer Thank for reading and sorry for my bad english  
  16. NS Runtime 1.30 v 8.1

    Hi  I prepared test application (attachment) and all the time when I start Runtime I get error: "Failed to initialize communication processing. Exit the application except Run and re-start the system." I think I did everything correct. Below my specs. CX Designer 3.730 NS Runtime 1.30 NS Runtime is on PC WIN7 64 bit  res. 1024x768 Maybe you can help to find the problem     test3.7z
  17. iFIX restore problem

    Hi, I have .fbk backup file of iFix aplication (i mean).. When I try to restore it by "Backup&Restore Wizard" in part where I "Browse" the way to Backup file and click on "Next" is problem. Pop-up window show -> "Bad file format. The archive file may be an old version or a wrong version in header signature or is not a Proficy iFIX full backup file (.fbk)" ....  My question is = Is possible to find what of version is my backup file ??? when i suppose this error mean i have installed wrong version of iFIX sofware (my version is iFIX 5.5).. Or is no problem of my iFIX version ?  Thanks
  18. i am using a VSD Altivar71 and controlling it through serial MODBUS communication, the probllem is sometimes after stoping the motor the drives gives the "nst" fault which means according to the programming catalouge "freewheel stop" it doesn't do that all the time but it happens a lot and after uploading the code again to plc the problem is gone for a while before it happens again. i am sure that the fault is happening because if communication because when i controll the drive from hmi it never gives that fault, i checked the setting and tried different cables but it still gives "nst" and motor never moves, i found that in catalouge but i am not sure how to address the problem.
  19. CP1E-N30DT with Hyperterminal PC

    Dear Expert, i'm issue to do communication CP1E with PC via RS232. im try to use plc for sending information and receive by hyperterminal pc. after googling some information there have multiway to success. by the way until now cannot settle. please expert share completed setup that's work: 1. communication cable from PLC - PC (my information use pin (2,3,9 jumper 4&5) - (2,3,5 jumper 7&8) 2. sample program that works (im using TXD & RXD with memory D1000 to keep data) 3. connection cable to PC using MOXA Serial to USB converter. 4. plc serial setting (default: 9600,7,N,1,Host link) my target to give instruction to printer to start print. printer need ACSII code. if this communication success i'm will convert all data to ACSII by ACSII convert function.   thanks,
  20. Hi everyone, I just want to layout the structure of the question. I have a GOT2000 (GT27* series) that I have hooked up and communicating with an Allen-Bradley PLC. I have established connection and can pull out certain tags values from the PLC program in RSLogix 5000. While I can read the tag values, I cannot modify them (in certain conditions).  So let say that I have a User-Defined Structure named "Smoke_Detector" and here are it's available members: Smoke_Detector:   - ALARM (BOOL)   - ON_TIME (DINT) * DINT in Allen-Bradley but Signed Binary 32   - Battery_Life (REAL)  My question is that while I can read and display the tag and its members through the following:   - LAMP for Smoke_Detector.ALARM   - Numerical Display for both Smoke_Detector.ON_TIME and Smoke_Detector.Battery_Life But when I tried to modify the values via a Bit Switch or Numerical Input, it does not operate on them.  However, if these tags are members are just standalone tags, meaning that they are not within a UDT in RSLogix 5000, then I can operate/ modify them just fine.  Here are the things that I have tried: * Making sure that the permission are set to Read/ Write in RSLogix 5000 * Making sure that the tag definition in GT Designer 3 follows the structure where @[channel]:[Network #]:[Station #]::[Tag instance and member (e.g Smoke_detector is the instance and Alarm is member] Any possible insight and input are appreciate! 
  21. Hi all !    I need a help about connection between mitsubishi GOT Simple series (gs2110) to kawasaki robot via crossed ethernet cable on tcp/ip protocol. I actually have a fx3g for main unit of my project, and also i have a kawasaki robot for slave unit. My purpose is basically to control both with HMI. I used RS422 between plc and got gs2112 and I want to use a crossed ethernet cable between robot and got but i did not communicate with ethernet even between pc and got. There is a manuel which I found on internet about GOT2000  Connection Manual (Microcomputers, MODBUS/Fieldbus Products, Peripherals) I think i need to work on  microcomputer connection (ethernet) subject, what do you think about that ? I need all advices and ideas which come from you.   [ROBOT]--------Ethernet--------[HMI]--------RS422--------[PLC] https://electrobit.ee/web/file_bank/Manuals/operaatorpaneelid/mitsubishi/GOT2000/GOT2000-connection-manual-ENG.pdf
  22. Hello All, What are the methods to get the monitoring data from A series PLC? I know its not supported any more, interface modules are not available...,    So the basically,   If I want to write customer software (may be embedded) what is the protocol I need to follow? I am connected to CPU unit by the way, there is no other modules except few digital and analog interfaces on PLC. Thank you in advance for your direction, direction in any way would help!
  23. Hi guys,  I have been trying to sync up my RSLogix 5000 tag to GT Designer 3 (GTD3) objects but I noticed that GTD3 only recognize certain native data types from Allen Bradley Logix5572 Controller (Model 1756-L72).  In the documentation that I found, it show that certain AB Native Tags are transferable to GTD3 Data Type (See the attached file "AB Tags to GTD3 Tags" ) One of the User-Defined Data Type from the RSLogix 5000 that I am trying to sync to Text Display Object in GTD3 is called "UDT_MY_CLTR_INFO" here is it's hierarchy of inheritance from RSLogix 5000     Name                                                                     Force Mask                                                                                   Data Type MY_CLTR_INFO                                                     (...)                                                                                                 UDT_MY_CLTR_INFO      MY_CLTR_INFO.NAME                                                                                                                                           STRING           MY_CLTR_INFO.NAME.LENGTH                                                                                                                      DINT           MY_CLTR_INFO.NAME.DATA                                                                                                                           SINT[82]    In my exported tag which is a CSV file, it doesn't list the sub-classes MY_CLTR_INFO.NAME, MY_CLTR_INFO.NAME.LENGTH, and MY_CLTR_INFO.NAME.DATA, it would only list MY_CLTR_INFO.  How do I link up my "Text Display" Object in GTD3 with the tag "MY_CLTR_INFO.NAME" whose Data Type is STRING and GTD3 does not have a STRING Data Type?  I appreciate anyone that took their time to read my problem and any attempt to help me out. Thank you. 
  24. Hello i'm new in all things about plc, i do a project for school and i use a festo fc 34 plc. The plc is programmed via serial port RS232 my pc not support a serial interface and i use a RS232 to usb adapter. when a try to download the program to plc give me a error: "ERROR: Cannot access controller".  What i do wrong.  Thank you in advance and sorry for my English. Have a nice day.
  25. C200H communication issue

    Hi We got 2 laptops Laptop1 communicates with a CJ1M and a C200H PLC. No problem. Laptop 2 communicates only with  the CJ1M, Not with the C200H, Same program, same conditions. I also tried with "Direct online" but no succes How can I get laptop 2 also to communicate with the C200H? Thanks