Search the Community

Showing results for tags 'gx developer'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 32 results

  1. ON/OFF Timer for Mitsubishi FX

    FB_TIMER_ON_OFF The FB is a part of RTC library and implements a timer, based on RTC, for ON and OFF a control bit, e.g. to turn ON/OFF a load in the time interval, and can be easily added into your program in desired quantity. The FB is supplied with E (Enable) input, EO (Output to Control Bit), and can operate in one of two modes: HMS = Hours + Minutes + Seconds (daily timer) MDH = Month + Date + Hours (yearly timer) Each setpoint of ON and OFF time settings should be represented as Array of INT [0...2] type and contain a time data according to the chosen mode. Thus, for example: - in HMS mode: a control bit can be turned on at 02:03:14 am and then turned off at 06:04:17 pm, or turned on at 05:12:27 pm and turned off at 07:06:22 am; - in MDH mode: a control bit can be turned on 3th February at 02:00 pm and then turned off 4th June at 05:00 pm, or turned on 12th November at 03:00 pm and turned off 6th March at 10:00 pm. If the values of both time settings are the same, the FB output will not be activated. Supporting PLC CPUs: All FX Program memory: - 34 steps per each FB instance - 4 steps for entire project (reading from RTC) System variables: M - 3 bits (for entire project) The library is compatible with GX IEC Developer and GX Works2 software . https://plus.google.com/105445006108716761629/posts/Z4v4F11s4Bz
  2. Hi guys, I have a problem with GX IEC Developer 7.04, i hope some of you can help me. When i try to connect with the PLC type - Melsec FX1s- 30MR-DC, there is an error: I check all COM port settings, and everything is ok. Com_port parameters: FX Parameters: Transfer setup: PLC Type in the program is the same like physical one (FX1s). I try to change all of this stuffs but there is no result. The cable I use for comunnication is this type: Thank you very much in advance. Have a nice day! eng R. Bukov
  3. Hi all and nice to meet you here! I hope that someone with experience helps me and I hope in future to offer also my help to someone. I am having problem with a Mitsubishi plc with A2N (S1) cpu installed on a machinery. The machinery stayed 20 days switched off and with battery empty as I realised when switched on and the problems come out. I changed the battery but the problem didnt resolved. The plc gave error with stable error led and flashing run led on the cpu. Also an error led stable on a (double role) module of printer and ram. I have to say that I have never used GX developer environment before and it is my first contact with Mitsubishi plcs. Reading some manuals (found on the internet) and by using GX developer I read from plc the faults. Register D9008 was set at 12 error meaning MISSING END INS. I Followed the described flow charts from a2n manual for reseting faults but the situation was the same always as described above. I tried to read the program from plc and succeded to read it. It is a lader with about 6000 lines. Anyway I have no previous experience of the GX development environment but I tried to put the missing END in the program as sugested also by the flow chart in the manual. At this point I have to say that it was automatically added from gx developer as I can remeber from an appeared message. I verified also many times the program on gx developer with the plc and the only difference was that missing END at the last line of ladder program. Anyway I tried to write back to plc the program with correct end but it was not possible. I tried several times. The error mesages took with Gx developer was the following : "THE SAME T/C COIL EXISTS IN PROGRAM (MAIN) AND/OR PROGRAM (MAIN-SFC). THE VALUES ARE SET TO BE THE SAME AS IN THE FIRST FOUND T/C COILFROM THE TOP OF PROGRAM" "THERE IS A DEVICE IN THE PROGRAM (MAIN) THAT IS OUTSIDE OF THE RANGE. CHECK THE PROGRAM AND CORRECT THE DEVICE THAT IS OUTSIDE THE RANGE." Anyway I decided to delete the plc memory. After that the run was stop blinking and the error led went off. Only the error on the printer-ram module was on (This module was changed with a know functioning one witout any variation on behaviour). I thought that problem has gone now that the cpu is empty. I tried again to write the program to the plc but again i take the above mentioned messages. Now I have an empty plc and a program on the Gx developer that cannot be written to plc!!!!!!!!!!!!!!!!!!!!!!!!! I am desperate!!! I do not know how to proceed. I am not knowing the mitsubishi development environment. Other than Gx developer I tried to install the GX simulation but it not works to my computer. At this point I dont know even if the ladder program is somehow corrupted after the described above messages. I can sent the code (GX developer project) and any other information to someone expert, if necessary, to have an opinion. Please help!!! Let me know how to proceed!! I have to write back the code to plc !!!!! Thank you all in advance!! Now i realised that there is SFC that is my problem. Could someone help please? Big part of ladder is in yellow color. How can i proceed?
  4. https://plus.google.com/105445006108716761629/posts/DzZy3GmFxT8
  5. Hi everybody! After several years at the forum this is my first question to experts: What is the syntax of INDEX_M and OUTEX_M instructions in GX IEC Developer IL? Thanks
  6. Hi, I have a challenge with GX developer version 8.63R (SW8D5C-GPPW-E). I'm trying to verify 2 projects (offline). Some programs I know there are changes but they are not shown in the verification. In 1 program I did see the last checked change was in step 1496 (next change I did see by manual check was step 1502. it seems like this type of verification is limited to 1500 steps to check. Is there any way I can make this offline verification work? the most progams that we have in our project are over 2000 steps. big thanks in foreward