Search the Community
Showing results for tags 'simulation'.
Found 16 results
Hitachi H-702 Series MODE SIMULATION
bolman885 posted a topic in Other PLCsHey, does anyone know why the simulation mode is on? how to change it? (LED SIM )
Problem Running CX-Simulator - KickEngine
innoaloe posted a topic in CX-OneSalutations! So recently I'm very confused with my CX-Programmer. Everytime I tried to run the Simulator from CX-Programmer, I always got a notice that a certain program called KickEngine.exe is about to Run. I look up for this program and found it inside CX-Simulator folder, so I decide to run it anyway. The problem is the simulator always return the error : "The selected port does not exist". In other words I cannot run the simulation. I understand that the simulator uses ControllerLink comm. between CX-Programmer and CX-Simulator, so I tried to run those two separately and build the connection, but also to no avail. Even so, since CX-Programmer 9.0, I believe there is no need to run the programs separately. Before I had a similar problem where the simulator cannot be run, and the error code is "Failed to Start Ladder Engine". This was solved by removing whole Omron software using CX-Remover, then reinstalling again. However, it doesn't solve the current problem. If possible I don't want to resort to reinstalling the whole OS... T_T Anyone has suggestions or ideas? I had lookup on an older thread and tested the measure taken there, and didn't solve this. Thanks!
Mitsubishi PLC communication with simulation program
PLCGrandMaster posted a topic in MitsubishiHello! Is there any possibility to connect a Mitsubishi PLC to a program like Siemens Plant Simulation? With Siemens PLC I can do it through OPC UA protocol, or Shared Memory with SIMIT, or stuff like that. But I would need to do it also with Mitsubishi PLC. Can I use for example OPC Server? I couldn't find out, if Mitsubishi PLC-s have that function built-in. (I have a L02 and a FX3S COU, either of them would be great.) Thank you!
genn posted a topic in Modicon / Telemecanique / Schneider ElectricHi all, Is it possible to simulate LMC058 PLC with ethernet in soMachine software. I want to test the logic written in PLC which uses tcpudp library.
Isp soft simulator problem
Rolo posted a topic in Other PLCsHi I am trying to run simulator in delta isp soft I have configured commgr and isp soft but when I try to run simulation I m getting this error. How I can solve this
Cx designer not supports test simulation with cpm2a/cpm1a
MuhammadRiyas posted a topic in CX-DesignerPls any one help me to simulate my omron HMI program with CPM 2A PLC Means help me to communicate cx designer with CPM 2A plc Or with NT- series support tool
Miguel.itlac posted a topic in MitsubishiHello There Im programming a FX5UJ but when i want to simulate, this option is not enabled , the version Ive got of Gx works 3 is 1.063R. Is there a way to enable this option? or is not available for being new version? Thank you in advance
MachineExpert Vijeo Designer simulation
dbozic posted a topic in Modicon / Telemecanique / Schneider ElectricHi guys, I installed new MachineExpert v1.2 and Vijeo 6.2.9 on Win10 machine. When connecting simulation PLC to Vijeo to test my application everything is good. I go to PLC and check the nodename (see the pic attached) which I put in my Vijeo application and everything works. Issue is, because of my hard drive capacity I am forced to work via VM (but this is my preffered way also because of number of PLC softwares used). When I installed from the same installer (everything same as my local Win10) on Win7 VM when I run simulation I get empty space where the PC simulator should be visible which nodename I should type in Vijeo. Also I noticed when going to gateway management console in VM the process is active, same parameters as in host machine. Turning off the gateway on the VM turns it off as well on the host. Is there a known problem of connecting to simulator on VM? Or win10? Unfortunately I don't have Win10 VM to try right now.. Anyone can help? Much appreciated!
Virtaul Axis - Simulation
BridgeAutomationSolutions posted a topic in NJ Series / Sysmac StudioIs it possible to simulate a servo axis in Sysmac Studio? Can you create a virtual axis and then set velocity & position for this virtual axis? If this is possible, is there an example program that anyone can share with me? Thank you. Happy new Year!
Start Ladder Logic Test
JMoriarty posted a topic in MitsubishiHi, there! I had got GX-Developer Ver.8, which is very different from the plc programs that I have learned before. I have read many tutorials and watch it but I still don't know how to start ladder logic test. Many other people simply click on 'start or end ladder logic test' but mine was greyed. Anyone has solution? Or I just missed a couple steps of simulation? Though it is very basic problem, I will put a deep gratitude for your reply.
Omron Learner posted a topic in Other Omron SoftwareHi. I am barely new into programation and I just wanted to know if there is a way to simulate an 3'' inch HMI (based on NV-Designer), since I don't have the HMI itself. Thanks in advance.
Factory IO Provides A 3D Simulation of the Process
gclshortt posted a topic in Computer Help and Networkinghttp://accautomation.ca/plc-programming-example-process-mixer/ Factory IO provides a 3D simulation of the process. Testing of the program is important and should be done in a variety of ways. Factory IO provides a straight forward method of seeing your program in action before you wire your application. The above URL link will take you to our example process mixer. We use Factory IO to simulate the application. Factory IO will communicate Modbus TCP to the PLC. Factory IO Website is at the following URL: https://factoryio.com/ Documentation is well done. Start at the ‘Getting Started’ at the following URL: https://factoryio.com/docs/ You can get a free 30 day trial at the above address. Regards, Garry
Factory I/O 3D simulation connect to Tia Portal V13
kidsolo1412 posted a topic in SiemensWith Factory I/O you can learn and test your program with a 3D view system Support many automation regular machine,support digital and analog signal too Have a look on this softwarehttps://www.youtube.com/watch?v=BFHqIj2DWd4
Unable to Monitor in GXworks2
markyspicer posted a topic in MitsubishiHi! Anyone can help regarding this issue. I'm not able to monitor the Motor Block that I have created. there's no error either in the output screen but i'm thinking what is the cause of not running in the simulation which shows the Motor Folder RED even it was compiled. thanks for the help! Note: I'm new in mitsubishi.
GX Developer Simulation problems
Jhona Daniel posted a topic in MitsubishiHello to everybody! I have same trouble with the simulation, I CAN'T SIMULATE :( The botton for simulation is not active, the PLC I'm using is a FX3U Mitsubishi. Any recommendation?
B&R, Problem with transfering the project.
Lahotron posted a topic in Other PLCsHi, I've been trying to run my project in Simulation (and check display on VNC viewer). When I try to download a procjet to simulator, then I get : "Error 8028 while transferring*: Wrong PV initialisation format" Can anybody help me with it? Please check attached pictures.