Search the Community

Showing results for tags 'auto updater'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 6 results

  1. Hi All, Just wondering if anyone here has any experience with automatically loading different programs to compactlogix. I am open to any suggestions. So far we have been putting sd card slots on the main panels since the extender cables are limited in length so the customer needed to swap sd cards on a tooling plate change out before powering up. One of our customers now would like to change the tooling plate and have the plc automatically load the proper program for it. We don't want to have multiple subroutines because sooner or later the plc memory will run out. We also have put smaller plc's on the tooling plates themselves to hold the specific programming for the tooling plate and handshake with main frame but this particular customer does not want this. I would like to know if anyone has done anything with wifi sd cards in CompactLogix or loading the program automatically from a pc to sd card and then switching the sd card to the plc via some kind of sd card switch before powering back up. Any advice is greatly appreciated. Thanks in advance.  
  2. Has anyone had issues using the Auto-Updater and Administrative Rights?  I am running Windows 10 Pro, 64Bit.  I need to update Sysmac Studio from 1.31 to 1.4.....when I run Auto Updater (as Administrator) I always get the error "Log on the PC as a user who has an administrative right when install" and it never makes it past the first module of the CX-One Update.  I even gave the issue over to my IT guy and he has absolute full rights to every nook and cranny on my laptop. I was told that I needed to allow the CX-One to updates as well since they share some of the same components. My IT guy even tried to do the "download" and install individual modules of the update and that still didn't work. Currently waiting on callback from OMRON Tech Support, thought I'd pose the question here as well....thanks.
  3. Cimplicity Auto Report Generation

    Dear All, I am having a problem with my cimplicity Auto Report Generation, When I Click on Generate Report, it shows "0 values collected" does anyone knows what's possibly could gone wrong here ??
  4. I’m using a Omron NJ to manage a LinMot linear motor .. all is going very well; however, there have been a few times during this development phase when the actuator, or programming creates a fault, perhaps from a following error, or exceeding a limit.  The result is sometimes scary.  The actuator might accelerate into a hard stop.  Not a big deal, the ends are protected with Sorbothane, so it isn’t a big problem .. yet.  Once the system is correctly programmed, it shouldn’t ever accelerate an actuator into the hard stops. In spite of my newbie-ness  to Omron programming I’m aware of the need to employ error & fault action that will stop a run-away actuator in closed-loop control, rather quickly. Just how to do that.. has evaded my research. I’ve noticed:  “FaultHandler”  in the W507 & W508 Manuals. And, been quite frustrated to not find any reference to FaultHandler or FaultHandeler()  .. which kinda suggests it’s a program?… and also expected to get some clues in the "NJ Programming Best Practices V1.1”   so far… no luck. Perhaps I’m going about this all wrong..  The LinMot Driver Controller might be the way to go.. An error message from the NJ to the LinMot drive would quickly shut down movement in closed loop .. instead of turning the motor into a rail gun… Any suggestions at how to do it with the NJ,  would be greatly appreciated.. Thanks Regards, Michael PS: here’s the progress so far, thanks to many out there, and on this forum ... https://www.youtube.com/embed/B0UGm9JTw3U?rel=0  
  5. Auto Run Mode after Reboot

    Hi guys! Im new in using PLC and im using CPM1A, is there a way setup the plc to run mode immediately after rebooting it, also even without connecting it to PC or handheld device? I saw in the manual "Startup Operating Module" but i am lost, i dont know how to configure it. Thanks for your advice.
  6. Dear colleagues and siemens experts, I''m new in siemens. As all I make my program for PLC, but I need help with PID autotunig (pretuning) I use : 1.CPU 1214C DC/DC/DC (6ES7214-1AG40-0XB0) 2. 6ES7214-1AG40-0XB02. 16IN/16 OUT DC/DC/DC (6ES7-223-1BL32-0XB0) 3. 2x 6ES7231-5PD32-0XB0 ( 4 channel RTD analog module - PT100) We use 7(seven) Pt100 points with 7(seven) heaters ... so I need 7 additional outputs..... [you can see example of wiring in attached pic 6es7231-5pd32-0xb0-modules.jpg] Maximum heating point is around 220 degrees. I make my configuration for PID_Compact : 1. Basic settings 1.1 Controller type : Temperature : °C Set mode to : Pretuning ( sometimes I make it Automatic mode) 1.2 Input_Per(analog) -----> Output_PWM 2.Process value setting: 2.1 Process value limits: Process value high limit : 220.0 °C 2.2 Process value limits: Default 3. Advance setting 3.1Process value monitor : Default 3.2 PWM limits Minimum ON time : 0.5 sec Minimum OFF time : 0.5 sec 3.3 Output value : Default 3.4 PID parameters : Default I start Commissioning with these steps : 1. Measurement : Sampling time 0.5 Start 2. Start PID_Compact 3.Tuning mode : Start When I try first time my setpoint was 90 degrees , second time I try with 120 degrees. After 4-5 hours it stop more in Progress bar it stop when I reach a little more then 50%, and I stop PID. For heaters it is not normal to process to be 4-5 hours, there have some wrong. Example with 120 degrees : During process I make : When Input_PER reach 120[1200] degrees I stop physical access to heaters. When Input_PER reach 100[1000] degrees I start physical access to heaters So 4-5 hours is soo long time for this type process. Time to reach 120 degrees from 100 degrees is around 2-3 min. Time to fall from 120 degrees to 100 degrees is around 4-5 min. Total time for one whole cycle around : 8min. Sometimes when I set setpoint to 140, 150 degrees it writes me that output set value is to high after I give Start Pretuning ? Even sometimes when try for 120 degrees .... As all I want to start PID pretuning (autotuning) with setpoint 140 - 150 degrees. Which are minimum requirement to start PID autotuning with PID_Compact ? Could you send me some very simple example and steps that I must make or only steps ? I attached files in dropbox with images and program example, because I can't attached nothing here. This form don't give me access to attached something. So link is here : Even program is there. Thanks in advance Best regards : Altan