Mark-

MrPLC Member
  • Content count

    280
  • Joined

  • Last visited

Everything posted by Mark-

  1. Comunication

    Using online translation he wrote: are you having problems with the extended module of PLC fx3u 32 MR-ES.? Specifically, what. X0-X7 sequence. X10-X17. The X20-X27, Y0-Y27 is right?   Me: Is your 485 terminated properly? I ask because you have not provided much information on the problem. Error codes? How is it wired? Tried another expansion module? Does the 485 bus work with any device? etc.    
  2. Comunicação

    And if English is not a language for you, you can use a free online translator. Create the message in Portuguese, use a translator, and paste the result here. I used Bing's translator for this message. E se o inglês não é um idioma para você, você pode usar um tradutor online gratuito. Crie a mensagem em português, use um tradutor e cole o resultado aqui. Usei o tradutor do Bing para esta mensagem.
  3. Reading inputs using FINS/TCP from a PC

    Hello, Download the trial/demo version of PeakHMI and use it for generating request to the PLC. Use WireShark to capture and analyze the request/response packets.
  4. Negative sign in HMI

    Did you enable the "Show Plus Sign" checkbox/property?
  5. Mitsubishi FX3U firmware...

    Thanks
  6. Mitsubishi FX3U firmware...

    Hello, Is it correct the firmware of an FX3U PLC cannot be updated?
  7. Hello, Is it possible to have a FX3U-ENET module on the right side of the PLC and a FX3U-ENET-ADP on the left side? If possible, how to specify the module number in FX Configurator-EN? Regards, Mark
  8. Mitsubishi FX3u Ethernet options...

    Neverov and Theuns, thank you.  
  9. Understanding 3E frame for FX5U PLC over SLMP

    Ummm the byte count starting at 9 to 21(inclusive) is 13 bytes.... so not sure what you are saying. If the binary read works the binary format is correct. You can download our demo of PeakHMI, use the "Q" Ethernet drive to read/write different areas of memory, use Wireshark to see the data packets. Assuming no difference for FX5, not tested here.  
  10. Understanding 3E frame for FX5U PLC over SLMP

    Hello, Here is a breakdown of 3E to a Q, writing Y12. I "think" it is correct.  
  11. Thanks for the response. All working now. The "open settings" in the "FX Configuraior" had not be configured correctly.
  12. Hello, I have an FX3u-16MR/ES, FX3u-ENET (version 1.0), using GX Works2 Version 1.596W (Trial version). Using FX Configurator-EN (version 1.0), the IP address of the FX3u-ENET is set and I can ping it with success. GX Works2 fails to communicate with the PLC, via Ethernet, and all other software capable of communication with the PLC fails when using Ethernet. I read one PDF about creating a new module under “Special Module...”. The only module listed is “AnyWireASLink”. Perhaps that is a limitation of the trial version. The document had “FX3u-ENET-L”. FX3u-ENET and FX3u-ENET-L seem to be different? Any ideas? Thanks, Mark
  13. Why does ML/1400 send a TCP [RST] ?

    SWAG, Get_Attribute_List
  14. Why does ML/1400 send a TCP [RST] ?

    Yeah the "keep-alive" at the TCP level and the "watchdog/keep-alive" at the CIP level are different. I guess the first question is why keep a polling/response type connection active/open unless it is used. That was rhetorical. Leave the TCP level to itself and only work at the CIP level because that is what is timing out. Did you retry the "List identity" command?  
  15. Why does ML/1400 send a TCP [RST] ?

    Do the test.
  16. Why does ML/1400 send a TCP [RST] ?

    I was going to write a bunch of stuff but decided at least one more test was needed. With no other connection to the PLC, issue the register session and forward open. Then doing nothing. How long before the PLC drops the connection?  
  17. Vista support for NS-Runtime

    Are you asking someone to commit a crime?
  18. OK, I asked because the specification is where I find solutions to most returned error codes. Word search (and patience) is your friend.
  19. You are welcome. Do you have the CIP specification to read?
  20. I do not know if that is the issue. I see the result "connection in use or duplicate forward open" and know I code so the connection serial number is unique across all connections.
  21. Are you using a different connection serial number?  
  22. You are welcome. You can use other port number yes. Is the slot (controller) part of the connection path?
  23. Ping from PLC

    And to add not all devices support/reply to "ping" request.
  24. DF1 Protocol For Bit Read

    You are welcome. From the DF1 manual: For higher addresses, setting this byte to FF expands this field to three bytes total. Use the second and third bytes for the expanded file address (low address byte first).