Search the Community

Showing results for tags 'barcode'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 15 results

  1. SLMP Failures

    Hello all,  I am new to using Mitsubishi and I am having issues communicating with my Cognex Camera. I have the camera configured in Datamn Setup Tool. I have the Ethernet card configured and validated. I am able to ping both devices and get a response on the network. However, I received an SLMP failure in Dataman and there's no communication between my camera and the controller.  Please see the attached photos to view how I have the camera and PLC configured.
  2. hi guys, I want to write a program to communicate barcode Reader via Wago PFC 200 PLC. Does anyone know about the library or function block which is used in Codesys to communicate between these twoThanks
  3. Greetings everyone. I'm new here. Hoping to get help to operate the Omron V400-R2 barcode to the Mitsubishi QJ71C24N so that they can communicate the two devices with the correct method. PLC: Mitsubishi: Q03UDVCPU; barcode: Omron V400-R2; serial communication module: QJ71C24N. I use RS 232 communication cable, I have tried using predefined protocol and non protocol procedures but still can't communicate the two devices. I really appreciate your help.
  4. Hello, I need to connect multiple barcode readers (SICK CLP510) to a PLC (FX3GE-40M) for a university project. I need a minimum of 3 bar code readers, but only have one operational, connected via an additional modul for the use of rs-232. The only other port I can use is a miniDin 8, which is a build-in rs-422 port. Because this is a university project, it needs to be as cost efficient as posible. All the readers are CLP510 (pin-out attached bellow) Thanks Becky Pin_out___wire_colour___signal_comparison_CLP100_CLP510_CLV60x.pdf
  5. Hello, I need to connect multiple barcode readers (SICK CLP510) to a PLC (FX3GE-40M) for a university project. I need a minimum of 3 bar code readers, but only have one operational, connected via an additional modul for the use of rs-232. The only other port I can use is a miniDin 8, which is a build-in rs-422 port. Because this is a university project, it needs to be as cost efficient as posible. All the readers are CLP510 (pin-out attached bellow) Thanks Becky Pin_out___wire_colour___signal_comparison_CLP100_CLP510_CLV60x.pdf
  6. FX5U SERIES

    Please find attached presentation of OMRON PLC . we have same requirement of Mitsubishi F5U series. Please suggent and send the sample programm. barcode.pptx
  7. Hello, I have a Datalogic GD4430 barcode scanner and a Omron NS5 touchscreen. When I scan a barcode that contains characters CR (0x0D) or LF (0x0A), nothing appears on the text input on the screen.Scanning a barcode that doesn't contains special characters (excepted STX and ETX) works perfectly. How to get a barcode that contain CR or LF characters ?Thanks
  8. Barcode string parsing

    Hi all, long time reader first time poster. I am an AB programmer through and through. Recently working on more and more omron gear and need a bit of a steer in the right direction. I have a sick barcode reader communicating to a omron CP1LE PLC over serial. Problem is the value from the barcode reader is not value, it is sometimes multiple values separated by commas (,). I really wish to only have the first value before the comma in this long string stored in D200.  I take it i'll have to move this string into individual container registries which i can easily go from there and pick which one I want to use. But how do I initially go about parsing the string in CX programmer? Attached is a screenshot of what I have so far> Cheers Dave
  9. Hello guys, I want some solution for my Mitsubishi Application. I have Visual Studio 2017 (VB.NET) and MX Component 4. I want to connect Q03UDVCPU (Q series PLC) through Ethernet connection. For Read (M0 Flag value and <if M0 is On> then read Barcode information also from PLC.) and write (M1, M10). How can create this transmission program. please kindly guide me. Thanking you.
  10. Hello,   I need to communicate a Datalogic Qw2120 ( with a USB connector  )  to a Modicon M251, it has a RJ45 Serial, i don´t know where to start , can anyone please give me a hand ? I would appreciate it very much.    
  11. Hello,   I need to communicate a Datalogic Qw2120 ( with a USB connector  )  to a Modicon M251, it has a RJ45 Serial, i don´t know where to start , can anyone please give me a hand ? I would appreciate it very much.
  12. My issue is trying to receive data from a Datalogic PM9500 barcode scanner onto a Siemens ET200S (IM151-8 PN/DP) CPU using a serial interface card (6ES7 131-4BD01-0AB0) with the ASCII Protocol. The software that I'm using to program the PLC is TIA Portal V14. I made use of the built-in function block S_RCV to try and receive the data into a data block that I have created. I connected the Datalogic's base charger unit directly into the PLC's SI module. (I cut the DB9 plug off) So, Pin 5 (RXD) of the SI module is connected to the Tx wire (Brown) of the scanner, the Tx is also connected, as well as the ground, to the SI module, however, I only require the Rx. There is no flow control. Upon scanning a barcode, the Rx LED on the SI card flashes, indicating that something was received. I have tested the scanner using a terminal program called "Hercules", and I am receiving what I should be when I scan something. The parameters such as Parity, Stop Bits, and Baud Rate, etc, of the scanner corresponds to that of the SI module as well. I paramatized the S_RCV block as follows: 1.) EN_R is always ON. 2.) R is defaulted to the instance DB that was created with the function block's tag.  3.) LADDR  is set to "100" as that is the start address of my SI Module as defined in the device configuration. 4.) DB_NO is set to "2" as it is the number of the data block I created for storing the received data.  5.) DBB_NO is set to "0", which I understand to be the data blocks offset start point from where to start inputting the data. The rest of the NDR, ERROR, LEN, and STATUS outputs of the function block are also defaulted to the instance DB tags. I only want to see if I'm receiving the data from the barcode scanner into the datablock. I created an array of bytes and I also tried with characters  from 0 to 30 to store the data. As I mentioned, the problem comes when I'm trying to scan something, the RX LED on the SI module pulses, but when I monitor for any changes in the Function Block, as well as for any changes in the Datablock itself, nothing happens at all.  I don't know what If I'm missing something, this has been bugging me for some time now, I'm quite new to the whole programming scene, I would appreciate any help I could, get also I've attached the project file too. =)   Yumi_Panel.zap14
  13. Hello, I'm looking to interface a USB barcode reader with a Micro820.  Is there anyway to interface a USB device with a AB PLC?  
  14. I have a CP1L by Omron and a barcode reader by Honerwell. I want to activate the serial port 1, to connect it with the reader. The reader shoul read one of the 2 main barcodes. If the reader get the barcode 1, then it should read 3 times the barcode A and activate an output; but if it read the barcode 2, it should read 3 times the barcode B, and also activate an output. I want made my programm in ladder programation, How I can activate the serial port 1? How I set the the serial port 1 as an input to the function block RXDU? How works the FB RXDU? How I can set the codes? How I set the fb RXDU as an output?
  15. Hi I am new with Barcode scanners. I want to trigger the barcode scanner from the plc and read the barcodein th ePLC. Howwill I be able to do this?