Search the Community
Showing results for tags 'FX3G-EEPROM-32L'.
Found 33 results
-
hello, I have problem with fx3g series PLC. I attached ladder program fragment.When I set momentary bit M1 don't send PLS M4, but if i set momentary M2 program running well. Why is it?
-
Hello, Need your advice. I am trying decimal number convert to binary and do output. for example If inside D90 I have 11 decimal number then for me need active output Y0, Y1 and Y3. I tried make this code below, but it is not work, don't active output . Maybe fx3g PLC have function how need to do it?
-
Hi. I'm hoping someone can give me an answer on this problem I'm having with a FX3GE PLC. I am trying to get a FX3GE plc to communicate to a drive over RS485 using a FX3G-485-BD card. In GXworks2. But am having no luck. I have tried changing the PLC communication settings in PLC parameters between CH1 and CH2, But am unable to get any communication working on the front port. I have also tested with a FX3G-232-BD RS232 card and have the same problems. There is no activity on the SD RD led's and no data being sent. If I put the FX3G-485-BD card in a FX3G or FX3S PLC I have running the same code it works fine. So the problem I'm having is with the FX3GE PLC Please can someone tell me what the difference is with the front Communication port on the FX3G and the FX3GE. And how I can get the FX3G-485-BD card working on the FX3GE PLC. Thanks
-
I used to use the Old Dos based MEDOC very many, many, years. I havn,t programmed for years now. We have GX Works 2 at work, and I am practicing programming an FX 3G - 40M to try and keep my hand in. Allthough I can write and read the program ok, the PLC keeps saying that it has no memory for the comments. Apparently the memory has to be set on the PLC. Any advice or information links will be appreciated
-
Good day, I'm new to this forum and to mitsubishi PLC but was hoping for some assistance with a programming issue. I have been through the hardware and programming manuals without luck for this issue. Hardware: FX3G-60mt FX3G-2AD-BE Settings: Structured ladder/FBD Current input mode on: M8260 (first board, first input) What I need to do is to record the peak value over a cylinder stroke period. The hardware manual explains how to average the value using averaging time, however I basically need to peak hold and send that to a D register for go no-go compare. Process as follows: Contact closed, monitor D8260, contact open, move peak value from D8260 during monitor duration to D205. Thanks in advance for any assistance. -Swervomotor
-
Hi I have problem to find eeprom bin or hex file to eeprom message memory on XBT-A72101. EEPROM is X28HC64P-12 and its dead complitly (before show message EEPROM FAULT, but after few restarts goes to runnig not now) . I have new empty eeprom and programmer but i don't have firmware file and can't read old memory beacouse not working. Could be somebody help me with this file. Best Regards. Michal.
-
Dear All, I really appreciate in advance your help in this problem. This is my first project with Mitsubishi PLC. I am using GX Works 2 for programming. Hardware is FX2G-24M base unit + FX2n-16EX extension module. I already started a new program and download simple rung on PLC, put PLC in run mode, test it and working properly. the problem is that I do not know what is the address of inputs of extension module. I tried to complete and use X016 but no response in PLC. kindly advise what shall I do. Thanks
-
Hello, Can a password protected PLC be updated with a help a memory cassette? The documentation states that it is not possible. But if the memory cassette is protected with the same keyword? Thank you.
