Donovanr
MrPLC Member-
Content count
106 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout Donovanr
-
Rank
Sparky
Contact Methods
- Website URL http://
- ICQ 0
Profile Information
- Location Auckland
- Country New Zealand
-
Running with Disconnected Servo
Donovanr replied to studey's topic in Allen Bradley / Rockwell Automation
If the axis is a part of a co-ordinate system then can the other axis still operate? You obviously need to remove the hardwired enable input when the table is removed. Have you tried inhibiting the axis programmatically using the GSV/SSV instructions? -
Donovanr started following Running with Disconnected Servo
-
HELP ERROR S55 KINETIX 6500 s55 velocity error or excess positon error
Donovanr replied to Joshua Alf's topic in Allen Bradley / Rockwell Automation
Is this a new install or an exisiting system? What is the full part number of your servo motor you have connected to the K6500? Are you using the hardwired enable input on the drive? -
Donovanr started following USB drivers location on Studio V1.17
-
USB drivers location on Studio V1.17
Donovanr replied to lamboom's topic in NJ Series / Sysmac Studio
Try using the original SYSMAC Studio install DVD to provide another path for the USB drIver file or reduce the file path C:\Program Files(x86)\Omron and include sub folders. -
Donovanr started following MicroLogix 1500 with 1769-SDN Scanner Setup Issue
-
MicroLogix 1500 with 1769-SDN Scanner Setup Issue
Donovanr replied to doublewai's topic in Allen Bradley / Rockwell Automation
Yes -
Donovanr started following Sysmac Studio Improvement Request
-
Sysmac Studio Improvement Request
Donovanr replied to BITS N BYTES's topic in NJ Series / Sysmac Studio
Twstevic: Not sure on your version but in v1.16 if you go to options, ladder view (I think it is) you have the option to align to the right and change the width also. Have a play with these settings. If your not a fan of green or pink tagnames/comments (which I'm not) you can mix this up too. -
Donovanr started following NA bad responsiveness
-
Which version of SYSMAC studio are you running? There is a new version that has just been released in the last day or to. Have a read under the 《HMI》 section of the 1.17 update. This sounds very similar to your issue http://www.fa.omron.co.jp/product/tool/454/sysmac-studio/e1_doc.html (Link supplied by Crossbow)
-
Donovanr started following Swapping out ControlLogix CPU's - Kinetix servo issue?
-
Swapping out ControlLogix CPU's - Kinetix servo issue?
Donovanr replied to GRMikeS's topic in Allen Bradley / Rockwell Automation
Which Kinetix drives are you referring to? What are the model numbers of the Servo motors? If you have absolute encoders you may have to re-home these using Motion Direct commands. If you do have absolute encoders check to see if the AxisXYZ.absolutereferencestatus bit is true in the L71 processor. (not 100% on the tag name at this hour of the day) After loading the project in to the L73 you might find this bit is false.. -
Donovanr started following Error - the target hmi project is a legacy project
-
Error - the target hmi project is a legacy project
Donovanr replied to PaulKim1003's topic in Allen Bradley / Rockwell Automation
The key word in your topic is legacy. There are already a number of other posts available on this one. http://forums.mrplc.com/index.php?/topic/30332-loading-ver-6-mer-file-into-factory-talk-studio/&do=findComment&comment=143344 -
Donovanr started following Addressing I/O
-
Try 4.00- 4.15 for the 2nd word of the 32 point input card.
-
What I suggest for your benefit is pay the money and enrol yourself in an Omron NJ Training course. There is an G5 Servo option to the course so attend this as well. You will learn tonnes of stuff on the course rather than flooding the forum with topics you have posted. I have been using Omron products for nearly 20 years. I still attended the course. Good luck
-
Find the manual and search for "external home input". You will be amazed at what you find when you know what is the available.
-
Donovanr started following Homing in Sysmac Studio, NJ501
-
Does the servo motor have a brake installed ? I have to ask, but has it been tuned for all of the motion move profiles you are trying to achieve? Whats the part numbers of the motor/drive and exlar actuator you have?
-
Check encoder cable shield has a good connection inside the connector at the drive end. Sometimes it pays to wrap the shield in copper foil tape to increase the surface area for the clamp. This will help in reducing the noise. Do you have a spare motor and encoder cable to try? Try ruling out one of the above.
-
Loading Ver 6 .mer file into Factory Talk Studio
Donovanr replied to Lupy's topic in Allen Bradley / Rockwell Automation
Check out Shawns invaluable blog http://theautomationblog.com/how-to-migrate-factorytalk-view-projects-to-windows-7-64-bit/ -
Allen Bradley 1783 Ethernet switch Replacement
Donovanr replied to Yahia Mounir's topic in Allen Bradley / Rockwell Automation
No, If you have a redundant ethernet network Etaps are required to connect to single port devices. Like Panelviews or DrIves. Unmanaged switches don't have this capability.