bjclem
MrPLC Member-
Content count
49 -
Joined
-
Last visited
Posts posted by bjclem
-
-
I have seen this problem with Heat or Noise Realed problems One thing you could Done is this in Rslogix 500 Software with the Program offline Click on the Card and Advance Configuration , Check the Ignore Configuration Error and download to the Micrologix Again this Solved a Problem i was having it tripped every 4 minutes or So . ( Note: this is a temperory Fix) Good Luck -
What are the expension cards , Sometimes this is a noise related problem . -
yes call ab support @ 440 646-5800 and you will have to sign a waiver for it and they will give you a password. -
This software has to run in dos , will work in windows 95 when you boot up in dos mode . And you will need a special interface Adapter for your PC . -
To use the 1796-sim1500 you remove the input Terminal block and replace with sim-1500 the 24vdc (+) & (-) is output from the PLC . I hope this helps if not Go to www.ab.com and Search for it on there home page . -
try Cycling power to the Secondary 1757-SRM rack and it will should come back up , this sometings takes a couple of minutes. -
what are you running XP pro Service Pack 1 or Service Pack 2 , there are problems with service pack 2 -
I am looking for the 1764-24Bwa and 1764-24AWa units electricial wiring drawings not the 2d or 3d from AB -
I am looking for autocad drawings of the mircologix 1500 base unit wiring , in .dwg format -
I am looking for the pinout of the Cable to interface the Pannel mate 1000 to a PC for uploading /downloading of programs -
Allen bradley does have a plc called a pico controller which , the software is free and cheap go the ab.com under processors take a look. -
for you go to ab.com and under user manuals onlines look at the PLC2 they will have the cable layouts in the back of the book . -
yes it can you will have to write a msg command to the Powerflex drive On cnet , -
yes you could use the powerflex 700 with the VC board that would work fine on you can go with the powerflex 700s but you will need a encoder and maybe a db or regen unit . -
for you the 1785-bcm would be the best this way keep the processors and will be able to do with equipment you have . any questions Bjclem@earthlink.net -
Rockwell has asset management which stores parts at your location call your local rep , because the 1395 is a good system drive. -
Call rockwell tech support they have alot of conversion utilites , I am not sure if that is one they have . 1 440 646-5800 -
Speed control is we the drive will ran in speed mode at the Speed requested , torque mode the drives runs at the Current reference that is requested , it will run it whatever speed is required to do this . This is used what you have 2 motors on a common shaft you what the load to be the same , so you run one in speed mode and the other in torque mode . I hope this helps . -
I agree with the PLC5/20 b if you send me the program from the plc2 , I could tell you are much a conversion would be , should not be that much being a mini 2 -
do you need to replace it , if you do the DL-40 would be the replacement . and the DL-20 convent into the dl-40 sofrware . Also if you are tring to upload or download you could use WinPFT transfer utility what comes with Panelbuilder 32 but only for uploading /downloading -
Need to know what motor it is , FLA 3 phase . If you have a Electrocraft motor than it sounds like it is a servo motor and then you would have to use a Ultra 3000 drive . Please send Motor data and could tell you if the Powerflex 700 would work. bc -
Could use various systems the Control Logix will work , the Basic card with be a prosoft card . The SLC 5/04 system would work to . -
the problem with the 1761-enet module there is a limit for the max nodes that can be on it which is around 6 AB pro
Micrologix 1500 Error Problem
in Allen Bradley / Rockwell Automation
Posted