Search the Community

Showing results for tags 'cxprogrammer'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 8 results

  1. Hallo, i want to connect Omron PLC CP1E use CP1W-CIF11 to AD4329A with RS485 communication.  my wiring is CP1w-CIF11     AD4329A SDA-                  SDA & RDA SDB-                 SDB & RDB and until now, i cant get data from AD4329A. Do you have any clue for this project?   Thank you Riandanu PLC to 4329A coba.cxp ad4329aex.pdf
  2. RS 485 with CP1E + CP1W-CIF11

    Dear all, I want to connect weighing indicator and CP1e with CP1W- CIF11 with RS485 Communication. and i attached screenshot setting for Serial Option Port, and cx programmer. in weighing scale i use 2400 and 7 even, and i attached a cx programmer too. and i think i cant read a data from weighing indicator. what should i do next?  PLC to 4329A.cxp
  3. Hallo, i want to connect PLC Omron CP1E to indicator weighing scale with modbusRTU connection and i have a CP1W-CIF11 module to connect indicator with CP1E. ,but I have no experience in RTU modbus communication in the PLC. How do i start?   *i just need output: 1. Coil (Reference No = 0. Output bits) for input switch with address 3 (Tare). 2.Input Status (Reference No = 1) for output lamp with address 17 (stable) 3.Input register (Reference No = 3) to read data with address 5 (gross weight) 4. holding register (Reference No = 4) to write comparison data with address 17(over) page 85 - 94 in attachment     ad4402_manual.pdf

    Hallo my name is Danu, i have a CP1E wirh CP1W-CIF11 and connect to modbus RTU device, i have done with write single coil, write single register,  read single register and read multiple register. But i try to write multiple register,  the indicator of CP1W-CIF11 is off and if i check d memory its no data. I attached my cx programmer. Can you help me create write multiple register in cx programmer?  Thank you AD4402-modbus edit edit edit edit edit.cxp
  5. Program help

    So I need some help with a program I am currently making, and wodnered if there was an easy way to make it. The function I need help with is this: There are 4 pumps, and 1 of them is going to start, after 10 sec shall the next start, so 10 sec after that the third one. And so like this it continues. But heres the clue. The pump which have been used the least is going to start first, if it is pump 1 that have been used the least, or if pump 3 has been used the least. If you know of any function block, or other way I can do to make this work, I would love the help.   (I know of the comparison blocks less than and more than, but with these I only can think of 1 way to make this work. And it would be over 48 function blocks, which I personally think is too much)

    Hye, I new in this plc understanding. For now I have this one ladder diagram that created in mitsubishi GX Developer that I use in winding machine as its plant. But, I have to make the FUNCTION BLOCK DIAGRAM for this part in CX Programmer. Can anyone help me how to construct the FBD in CX Programmer from this ladder diagram understanding . And did it is actually the counter function ? *the picture showed the ladder diagram*
  7. Hello,  I have to communicate Trane chiller to CJ2M-CPU34 with CJ1W-SCU31-V1 module via Modbus RTU RS-485. Do you know the best way to do this? Any advices? I attach Modbus registry from slave device.
  8. I have one CJ1M-CPU13-ETN PLC and two NS8-TV01-V2 HMI panels. I want the two HMIs to run the exact same CXDesigner program, and both of them to communicate with the same PLC. Is this possible to do? More specifically: for the same button on both HMIs, could I assign it the same working bit, or would this cause a conflict? Would I need to give the same button a different working bit for each HMI? Thanks!