Search the Community
Showing results for tags 'activation'.
Found 4 results
Ambroise posted a topic in Allen BradleyHi guys, I have a desktop with rs logix5000 activated with dongle and i want to activate rs logix 5000 on a laptop.Those 2 PC doesn't have internet.So I copy in the laptop license files of the dongle in the activation file , I see the available activations in FTA, but the activation in RS doesn't work even if I refresh the server...thx for ur help ! ;)
dynamicboy posted a topic in Allen BradleyDear Friends; Good day. First i install the windows virtual xp mode on Windows 7 64 bit. After installation i installed the FTM, RSLINK,and rslogix 5.0 in virtual xp mode. Then i activate the software by Factory talk manager and select the hard disk and for a single computer activation. This process successfully acomplished. But when i open the RSLOGIX it shows popup that activation path is not found. Then i again open the factory talk tool and note that there is no activation shows in current activate products, But the activation detail shows in the RE host tab. I re hosted the activation by using go to Rockwell site and message show successfully activation re hosted. *** Now i am stuck here is i loss my activation? *** in windows xp virtual mode how i activate my product that application find the correct path of activation file? ** In windows xp mode if i open my Computer there is shows other hard drive partition as well as Local disk C:\ and activation file save in virtual drive instead of real C drive in windows 7. But there is no file path option to save the activation. Its by default save on C:\documents and setting\all user\shared documents\rockwell\activation\***** Please help me how i activate my product in windows XP mode successfully? Thanking you. i will remain Regards
MrAutomation posted a topic in Allen BradleySo here's the problem I'm facing. I've recently started working for a company that has two facilities. They have lots of old equipment/PLCs, plus some new stuff. We undertook a project to upgrade the network infrastructure, and replace all the old programming terminals (Some had Windows 2000!) with a new standardized programming terminal, all sharing a common image. We've installed these new computers, and they were working great. Recently, we switched all the licensing to a Hyper-V based server, using FactoryTalk Activation Manager. Right off the hop, there was issues with one of the sites (let's call it site B). Site A is working fine. When you open FactoryTalk Activation manager, it populates the activations from the server in about 1s. The wait times for opening software are pretty normal (For RSLogix 5000, "normal" isn't exactly rapid, but like I said, that's normal). For Site B, the activations take forever to refresh in Activation Manager when opened on a programming terminal. The software takes even longer to open (we're talking about 2-3 minutes). Network wise, Site B is further along than Site A. We've implemented a Stratix layer 3 switch at the top of the network and use area specific VLANs to reduce multicast noise across the network (much of the multicast noise comes from vendor equipment, not PLCs, so I can't control it). This works fine. I can remote in and use TeamViewer/VNC with acceptable performance across the network, so it's not being bogged down to unacceptable levels. However, connection to the activation server is unacceptable. I'm not sure of the culprit (yet). We are continuing network improvements, removing some older 10/100 links and installing Gigabit equipment between the Hyper-V server and the above mentioned Stratix, hopefully that might help. However, that same 10/100 link is the one I use to remote in and use Teamviewer currently, so I can't see how much improvement it will give us for activations (which really should take almost no network traffic). To get activations, I'm just adding the IP address of the Activation Server into FTActivation Manager on the programming terminals. Any ideas, people? Thanks
Hi group, I am trying to return an activation that I believe was left on my VM when I deleated the RS Logix software. I have reinstalled Activation Manager to see if I can return the activation. (The activation list from the server shows my VM as having an activation and expires next year! Thats why I need to return it so other workers can use it.) In the attached images is the LIC File the license and if so why would it not be seen in Activation Manager? How do I go about returning this if it is a borrowed license?