Milosh

MrPLC Member
  • Content count

    46
  • Joined

  • Last visited

Everything posted by Milosh

  1. What is the difference between these two bacplanes? Can we mount cpu to io expansion backplane?
  2. Cpu position in rack ?

    Hi all Is there any problem if CPU is put like this (from right to left) slot 1 - PA209R slot 2 - ID231 slot 3 - ID231 slot 4 - OD231 slot 5 - OD 231 slot 6 - CS1H-CPU64H   On CPU is program logic (with all configurations). CPU have different rack informations. I need to put it on rack (above) and upload program code to PC.    
  3. Is there any problem if cx supervisor installed on the same machine with cx programmer and cx desiner? Some driver problems, etc. What is your expressions?   Best regards, Miloš
  4. Upload project from NS5-SQ10

    Hi all, Can someone explain how to upload project from NS5 HMI? 1. Which cable to use and which software? I tried with crossover rs232 cable to port A, but can't upload project? 2. Is it better to use USB cable? 3. Do I need to change something on DIP switches on HMI device?   Best regards, Miloš
  5. Upload from CS1H PLC?

    Hi all. I want to know what is the procedure to upload project from PLC model CS1H? Does the PLC goes to stop mode if I start uploading? Best regards, Miloš  
  6. Upload project from NS5-SQ10

    Is that cable same as connecting to Omron PLC CS series? Should I need to do something on the PT before transfering? Or on the Cx-Designer?
  7. Upload from CS1H PLC?

    I should to connect with direct (auto) mode?
  8. Hi all,   Is there any way to change title bar settings for pop-up screen like font, close screen icon etc?   Thanks in advance, Miloš
  9. Change title bar of pop-up screen

    Thanks for reply. Yes, that is one solution, but in that case I don't have posibility to move pop-up screen around the base screen.
  10. Change title bar of pop-up screen

    Close button on title bar is all grayed, and like that, is not have good visibility. I hope that I can change it to standard red button with white X.
  11. Hi all. How to detect on 10bit gray code absolute enncoder that one wire is broken? It is wired to plc digital input card. Is the solution to use timer and check every wire if signal not change during defined time interval then set error...or something similar?
  12. Detect wire break on omron absolute encoder

    Thanks all for reply. Sergei: Yes, I would like to have possibility to detect broken wire as soon as possible. gclshortt: Sometimes the encoder will not move for full turn. Operater can start machine, and very fast can stop. In that case encoder would not make full turn. Also sorry for my previuos wrong answer, about full turn. I thinking about this solution: when machine started, encoder turning, for every wire (signal) I need to check if state changes during defined time interval. If state changes everything is ok, but if not I shoult to stop the machine and set error flag. But I need 10 flags for errors, and 10 timers to detect that. I'm just looking for some easiest solution.
  13. Detect wire break on omron absolute encoder

    Yes, encoder makes full turnduring operation.  
  14. Detect wire break on omron absolute encoder

    Thanks for reply.  I have 10bit omron encoder with gray code. Every of this bits goes to one digital input on digital input module.   
  15. Detect wire break on omron absolute encoder

    Thanks, but I can't use this instruction with plc  I have. It is cs1d and gry instruction is not supported.  
  16. P_WR, P_CIO

    Hi all. For what this system flag is used?  
  17. Finnaly I change IP address. I use words DM30198, and DM30199 to set IP address. DM30198 #C0A8 - as 192.168 (first two segments of IP address) DM30199 #001F - as 0.31 (second two segments of IP address) When used only rotary switch, it changes only the last segment of IP address - so the address always stays as 192.168.250.xxx where xxx - rotary switch settings.  
  18. Hi all. I use CPU CS1D-H with duplex module CS1d-DPL02. In main rack I have CS1d-ETH21(ETH11 Mode) module. Set node addres unit no to 1, and adress node 1f as last segment of IP address 31. In IO_tabe unit setup address of the module is 192.168.0.31. After that I change communication settings in CX programmer to Ethernet and IP address like above. But can not connect to PLC. What I miss?
  19. I also tried to change the IP address from web page. Goto http://192.168.250.31/0 and go to Settings-> System and login with ETHERNET  After that IP address which is set is 192.168.0.31 and subnet mask is 255.255.255.0 I click on Set and then Regist. Turn off the whole rack with CPU and ETN21, then on, after that address is not changed. It's stay 192.168.250.31  
  20. Finally, I set up address in Unit setup to 192.168.0.31, dial switches set to 1 for x16_1 and F for switch x16_0. Then I use wireshark...bum...I get Ip address for omron as 192.168.250.31... Why????   Now I can connect with this address 192.168.250.31, but in unit setup is set address 192.168.0.31, and subnet mask 255.255.255.0   Im not sure why third segment of IP address is not changed to zero. Instead of that it is 250???
  21. I tried everything... Configuration of Unit is good. LNk led ON, RUN led ON, 100M LED on. I cnt't ping my card. My comp and card is in the same subnet. I don't know what is the problem...    
  22. Yes the subnetmask is ok: 255.255.255.0 I set 1 on rotary button x16_1 and F on rotary button x16_0... I tried with a switch, crossover cable...
  23. Thanks for reply. I can't ping tha card via Command promt... Its not CS1D-ETH21. It is CS1W-ETH21(ETH11 mode), my mistake. I can see it in Cx integrator, but can't ping.
  24. Hi all,  Can you provide me some simulator for unitronics, visilogic plc series?