Govind Lathkar

Ok If you consider about Mitsubishi Following are types a. Redundant Remote I/O system b. Redundant Local I/O system c. Multiplexed remote system d. Redundant CC-Link system- Remote I/O e. Redundant CC-Link system- Remote Adaptor I want to compair in turms of CPU, cable, power supply, I/O Regards Govind L. Lathkar

Dear All I want to compair plc redundency 1. Mitsubishi 2.Allen-Breadly 3.Siemenc 4.Scenider Pl add your views Regards Govind L. Lathkar

can we discussed the comparision between S7-200,Micrologx and FX3G PLC Now mitsubishi is introducing FX3G as a successor of FX1N. since If we see that feature of FX3G is better the FX1N. My quection is FX3G is better then S7-200,Micrologx If yes why or if not why Regards Govind L. Lathkar

Thank you I have developed one program Govind L. lathkar MX_Component_1.zip

Dear all I want sample program developed in VB6 to communicate with Q00JCPU on programming port using MX component thank you Regarda, Govind L. Lathkar

Dear all Can any one give me sample program for QD75 PLC program for 2 axis Lenear interpolation and Circular interpolution Regards Govind L. Lathkar

Dear All, I want Q CPU Programming port Portocol, Since I am developing program In vb to communicated with Q PLC, If I use QJ71C24N ( Serial communication Module ) or QJ71E71 ( Etherner Module ) or Modbus Module it will increase the cost. So I am tring to communicate on programming port can any one help. Regards Govind L. lathkar

No there is no error. But scada is giving error. I have Ellipse scada Driver which is developed in 3E Ascii format

Thank you I am really impressed by your quick response and very good knowledge. Here I am using Ellipse Scada It is not communication can you Help Govind L. Lathkar

I Mitsubish developed GX Works2 which is better then GX Developer I this Crossbow has raise same point Regards Govind L. Lathkar

Dear all, I have Q06UDECPU. I want to connect SCADA on buit in ethernet port of Q06UDECPU, What are the ethernet setting required in PLC parameter for Q06UDECPU, I have already done communication between SCADA and QJ71E71 Ethernet Module. I want to use same scada and Communication drive. Is it possible Pl help Regards, Govind L. Lathkar

Dear all, I want to Communication between FX3U-ENET and NI cRIO-9014 on Ethernet. Here I will use No protocol mode for FX3U-ENET in FX3U. Dose any one Have sampal PLC program for NI cRIO-9014. dose any one done such time of communication. Pl help. Regards, Govind L. Lathkar

sorry custmor will not allow. I thnik this forum is for such tricky solution

Thank for replay yes FX1n dose not support real number. in fx1n no log or antilog fonction present, no exponential function present.. I want any idea to solve it. regards govind l lathkar

Dear All I want or show data on GT15 I have 1. FX3U PLC + FX3U-ENET - 2 Stes 2. QPLC+ QJ71E71 - 1 Set It is showing data of 2 FX3U PLC on GOt or QPLC data but both FX3U PLC data and QPLC data can not shown on GOT actually it is not allowing to configure QPLC ( QJ71E71 ) and FX3U ( FX3U-ENET ) in GOT program is possible what I am doing regards Govind L. Lathkar