Govind Lathkar

Dear All I want to compair plc redundency 1. Mitsubishi 2.Allen-Breadly 3.Siemenc 4.Scenider Pl add your views Regards Govind L. Lathkar

Ok If you consider about Mitsubishi Following are types a. Redundant Remote I/O system b. Redundant Local I/O system c. Multiplexed remote system d. Redundant CC-Link system- Remote I/O e. Redundant CC-Link system- Remote Adaptor I want to compair in turms of CPU, cable, power supply, I/O Regards Govind L. Lathkar

can we discussed the comparision between S7-200,Micrologx and FX3G PLC Now mitsubishi is introducing FX3G as a successor of FX1N. since If we see that feature of FX3G is better the FX1N. My quection is FX3G is better then S7-200,Micrologx If yes why or if not why Regards Govind L. Lathkar

Dear all I want sample program developed in VB6 to communicate with Q00JCPU on programming port using MX component thank you Regarda, Govind L. Lathkar

Thank you I have developed one program Govind L. lathkar MX_Component_1.zip

Dear all Can any one give me sample program for QD75 PLC program for 2 axis Lenear interpolation and Circular interpolution Regards Govind L. Lathkar

Dear all, I have Q06UDECPU. I want to connect SCADA on buit in ethernet port of Q06UDECPU, What are the ethernet setting required in PLC parameter for Q06UDECPU, I have already done communication between SCADA and QJ71E71 Ethernet Module. I want to use same scada and Communication drive. Is it possible Pl help Regards, Govind L. Lathkar

Dear All, I want Q CPU Programming port Portocol, Since I am developing program In vb to communicated with Q PLC, If I use QJ71C24N ( Serial communication Module ) or QJ71E71 ( Etherner Module ) or Modbus Module it will increase the cost. So I am tring to communicate on programming port can any one help. Regards Govind L. lathkar

Dear all, I want to Communication between FX3U-ENET and NI cRIO-9014 on Ethernet. Here I will use No protocol mode for FX3U-ENET in FX3U. Dose any one Have sampal PLC program for NI cRIO-9014. dose any one done such time of communication. Pl help. Regards, Govind L. Lathkar

No there is no error. But scada is giving error. I have Ellipse scada Driver which is developed in 3E Ascii format

Thank you I am really impressed by your quick response and very good knowledge. Here I am using Ellipse Scada It is not communication can you Help Govind L. Lathkar

I Mitsubish developed GX Works2 which is better then GX Developer I this Crossbow has raise same point Regards Govind L. Lathkar

Dear All I am using FX1N PLC Here D10 and D12 are real value. here I want to calculate 5.123 rase to the power (6.456 ) e.g 2.12 ^ 2.34 = 5.80264384 thanking you Regards Govind L. Lathkar

sorry custmor will not allow. I thnik this forum is for such tricky solution

Thank for replay yes FX1n dose not support real number. in fx1n no log or antilog fonction present, no exponential function present.. I want any idea to solve it. regards govind l lathkar

Dear All I want or show data on GT15 I have 1. FX3U PLC + FX3U-ENET - 2 Stes 2. QPLC+ QJ71E71 - 1 Set It is showing data of 2 FX3U PLC on GOt or QPLC data but both FX3U PLC data and QPLC data can not shown on GOT actually it is not allowing to configure QPLC ( QJ71E71 ) and FX3U ( FX3U-ENET ) in GOT program is possible what I am doing regards Govind L. Lathkar

thanks for replay I know fx1n dosen not support real no. actually I want to know any method to calculate above logic, small program which can solve above regards Govind L. Lathkar

Dear All, I have following configuration System -1 Q02 PLC, QJ71E17 QJ61BT11N - (Master) Q ( D/A Module ) System -2 FX3U PLC FX3U-64CCL System -3 FX3U PLC FX3U-64CCL I have formed CClink Network between BT11 and 64CCL I want to upload and download FX3U PLC program Is is possible. Is any addition hardware required for it Regards Govind Lathkar

Dear All I have 4 no Q06 CPU. I wnat to share data to each other. for that I have taken QJ71BR11 to form PLC to PLC N/W For this I have assign PLC 1 as control station and PLC 2,3,4 as Normal station. What will happen if PLC 1 ( Control station ) is not powered on. Is rest or PLC( PLC 2 ,3,4 ) will communicate with each other Regards Govind L. Lathkar

Dear sir, thank you for replay. Here QJ71MT91 will be slave and scada will be master In Modbus serial Modul ( QJ71MB 91 there are two port so we can connect 2 SCADA, one for 232 port and other is connected to 485/422 port. But here in QJ71MT91 there is only one port so how I can connect 2 scada Here I want to access all data regester present in plc. It will not possible if I use this module as master module and scada as slave Regards Govind L. lathkar

Dear All, I want to connect 2 scada as shown in attached file. Is is possible if yes Pl give sampal program Regards Govind L. Lathkar 2_SCADA___QJ71MT91.bmp

Dear All, I want to know guidelines for using safety plc My requirement safety input 20 DI - 500 D0 - 400 Here should I use only safty PLC or safty + normal PLC combination Regards Govind L. Lathkar

Dear all I developed PLC Program for QJ71MB91-Automatic communication Function Setting is as below QJ71MB91 - CH- 2 - Master I have find difficulty that I can not generate Function - 6 using Automatic communication Function i.e. single word write is not possible. It is only generating Function 16. But my slave module is not supporting Function - 16 is there any war to develop function 6 Regards Govind L. Lathkar

Dear all I requird GX-IEC Training Manual Regards Govind L. Lathkar

yes, I have that manual which is present on Mistusibishi-automation site. Actually I ma looking for manual or PPT and sample program for giving training as will as presentation of GX -IEC thank you Govind L. Lathkar