-
Content count
2624 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Calendar
Everything posted by Gambit
-
https://wetransfer.com/downloads/8c921f4d80e253efa0b3e67d298b3c5a20230502141219/c7b833642276d45f68853e394df3c4af20230502141239/1a516e I forgot to mention you can also open an IEC project with GX Works 2
-
It's an end of life product. I can provie you with the latest installer if you have a installation code for it. Or you can ask Mitsubishi Europe
-
Haven't noticed anything but 20-25 years is not so bad. Strange that you have 10 at the same time though. Do you have extreme high temperatures ?
-
How to work with special registers in a LCPU L0 structured project on GX Works2
Gambit replied to Igor Lasmar's topic in Mitsubishi
https://www.mitsubishielectric.com/app/fa/download/search.do?kisyu=/plcl&mode=manual -
Need a simple 1 second pulsed output with button push
Gambit replied to Soundman5535's topic in Mitsubishi
which software are you using ? The TON TOFF instructions should be fine for this -
ok if it's an FX than you should use the special high speed counters. You can use an AB counter aswell
-
Also which PLC are you using if it's a modular version and you want the currect status of the input you shuld use DX0 instead of X0. or else you get the value from before the scan
-
yes but there is a difference between a password for the porgram and a password for the connection. For the weintek you will need an SLMP connection for the MX connection use MELSOFT Connections. Your example is correct !!!!
-
Do you have a password on the ethernet connection ? It should be melsoft not SLMP when usning Mitsubishi hardware/software
-
Sure just make some extra melsoft connections in the ethernet port parameters
-
nee een word device van de GOT zelf GS GD GB ---- GOT special - GOT Data - GOT Bit. Je kunt hier met een word switch een waarde in zetten on incrementen. Alle GS... Devices staan in de manual
-
Bij de GOT 2000 kun je die instellen met Intensity Control (GS455). Waarschijnlijk heeft de GOT1000 serie die ook
-
Elke PLC heft een netwerk en stationsnummer Zie bovenstaande screencpature. Deze gebruik je bij de adres invoer. Druk op het knop naast de device invoer, Dan kun je onderaan aangeven of het van de host connectie komt of een andere controller. Je kunt ook 1-2 invoeren voor het adres (netwerk 1 station 2)
-
Yes by checking that same button or you can update the firmware if the panel is not to old. But it would be better if the firmware matches between software and hardware. you shuld be able to install the old software aswell
-
If you disable check terminal version in the tranfser settings you should be able to do an upload of the pogram.
-
The usb => R232 creates a virtal serial port. Are you sure you are using the right port number ? Also I would try another converter and check if you are using the latest driver for it
-
Je kunt een speial function switch aanmaken om naar het utillity scherm te gaan of direct naar display.
-
Op de Extended tab kun je een security level aangen voor display en voor bediening. De security level kun je instellen op je system Blad. Deze kan gekoppeld worden aan eeen word device inde GOT of PLC. Zodat je het security level kunt monitoren of wijzigen vanuit de PLC.
-
Which PLC are you using ? FX .. In that case it depeands on how the S/S is connected. If you connect 24V to the s/s than you get an High signal when 0V is connected to the input. If you connect 0V to the s/s than you get an High signal when 24V is connected to the input.
-
Make sure the CAB5 is in connected the right way. only one side is for the PC !!
-
Dan heb je geen connectie of bestaat het DB niet. Misschien afgeschermt in de 1200
-
Ik zie niets geks dus het lijkt me de device referentie die niet goed is. Zie je niets of "0"
-
Hardware van Mitsubishi gaat jaren mee. Tevens 1:1 uitwisselbaar mocht het kapot gaan
-
picture 3. In the comment selection you probably need to set it to comment no. Your software is a little older than mine i think