Search the Community

Dear Sirs/Madams, I am studying to connect between GOT1565 and Microcomputer/PC via RS232 However, I only see the documentation for GT-A900 and GT-F900 So, I'm wan to ask you: Can GT1565 connect with Microcomputer/PC via RS232? Who did it? can you help me? Thanks so much!

Hi All, I have problem about programming serial module Mitsubishi PLC using QJ71C24N. If I unconnect the cable from the module and connect again it show SIO error and the communication become lost or not sending data again. so i have to restart the PLC to make it normal again. Any other solution for solve this error without restart the PLC? Thanks Husanto

Hi all, Im trying to figure out how to create non-volatile memory tags in GX Works 2 (using a FX3U controller), so that the values stored in the D registers won't keep zeroing out every time the controller powers down. Does anyone have any helpful tips on how this is done? Thanks

Hello All, I want to read data from a Control Logix PLC, into a PLC5/60, using Ethernet and a MSG instruction in the PLC5. When verifying the MSG instruction in the PLC5, I get an error message. "Target Address in invalid". Once I figure out how to do this I need to replicate it in another PLC5. Scope is to read the status of 4 paint pumps controlled by the CLX. If any of the 4 stop, the PLC5 needs to know, because it is controlling the paint application equipment. Source data resides in a Control Logix 1756-L63. The tag is INT type, 4 elements long, and the name is PUMP_STS_B2. The IP address of the CLX is 4.2.6.230. There are 2 ENBT cards, one in slot 1, and the other in slot 3. 4.2.6.230 is slot 3. PLC2,5 / SLC Mapping has been created in the CLX. File=421 Name PUMP_STS_B1 and File=422 Name Pump_STS_B2. The file mappings represent a binary file created in each of the PLC5's B421:0~4 in Booth 1, and B422:0~4 in Booth 2. The PLC5/60 is Enhanced series E model using the Ethernet side card. The IP address of the PLC5 is 3.26.5.61. I also created MG file types in each of the PLC5/60. MG420:0~19 in each processor. This was necessary to use the MSG instruction in the PLC5. I have searched the forums for examples of how to do this with no solid results. I am trying to follow the best practices of reading the data into my PLC so anyone who follows can tell where it is coming from. While the IP addresses are not closely related they should be able to communicate. I say this because all of our PC's are on the 4.2.6.XXX network on a 255.255.252.0 sub net and we have no issue communicating with the 3.26.5.61 IP address. Any help and advice would be greatly appreciated. Regards, Mike Carter

Hi all! I need advice. I have Mitsubishi Q02UCPU with profibus module QJ71PB92V. I try to connect communication module from Balluff BNI PBS-507-000-Z011 via Profubus without success. Everytime I connect module, I see diagnostic alarm "The parameter transmitted by the master is incorrect". All settings were made by default. QJ71PB92V has 0 adress and Balluff BNI PBS-507-000-Z01 has 11. I connected this module to the Siemens CPU-315 and it is work correct. From this forum I see it is common error. What will be the next step to check or solve the problem? I am not profficient in Profibus networks, so I will be appreciate for any help!

Can anyone help with a carwash program? I am currently a student and having a very hard time getting this to work. I am using GX2 software. Any help would be greatly appreciated. Jeff

I'm having a bit of difficulty with the MSG function on a logix5000. I'm simply trying to get a REAL value ("BH5_Flow") out of another logix5000 and assign it to a tag in the PLC. I've created a MSG function and created a new tag "BH_5_Flow_MSG" for the message, and created "BH5_Flow_M" for the value that will come from the MSG function. When I click the "..." button to bring up the config, I put the following in: Message Type: CIP Data Table ReadSource Element: BH5_FLOWNumber Of Elements: 1Destination Element: BH5_FLOW_MIn the PATH tab, i then put the following in: Path: LocalENB, 2, [iP ADDRESS OF SOURCE MACHINE]When I test the edits, I then get the ERR bit activate with error 16#0004 when the message rung runs. Anyone got any ideas where Im going wrong? I've practically copied another MSG instruction from further up the ladder but it doesn't seem to work

Hello guys, i would like to know if is possible keep always active the run command in a vf drive and for stopping the motor only send 0 reference. It´s possible??? because I want to program a ramp function in my plc for start and stop one motor. could someone tell me how to do this type of control please?.

Dear experts, I have been trying to flash parameter to QD75MH1 module from PLC. Every time I monitor the servo via GX-configurator QP, I find 0 error, 0 warning but in the history tab it shows "start not possible(108)". But when I did it by flashing the parameter by GX-Configurator QP(Specially invalidating forced stop option" it works fine and servo motor jogs. can anyone help me to write the forced stop value from PLC program?

Hi, I have a problem with my BC9020 and hope that someone can help me. I managed to set the IP adress of my PLC in the 10.2.5... add a root, run a program and make the PLC working for a while. I then tried another program, a new one... and now that I want to re-read the first program, Twincat System Manager doesn't allow me to enter in the "run mode" and stays in "config mode". It also has lost the IP address I set (10.2.5.....) and came back to the 172.16.22... (manufacturer settings) I cannot determine if the problem is in the PLC Control or In System Manager... This is my method to change the IP *** IP config *** 1) Reset the PLC First I place the end terminal next to the PLC. I set the DIP switches 1,6,7 to ON, power on the PLC and power off. I set the DIP switches 2,6,7 to ON, power on the PLC and power off. I set the DIP switches 1,2,6,7 to ON, power on the PLC and power off. 2) Set my PLC on the same AMS than my own IP (172.16.22...1.1) 3) In System Manager, add a new route 4) change the setting in I/O Configuration -> I/O Device -> Device 2(BX9000) -> clic on BX9000 define "set IP Address" to Manual define " IP Address" to 10.2.5...., the AMS change automatically. Press the configuration button and then Ctrl+F4 (run mode) This method worked but seems not to be the best... If you have any Ideas ? or questions? Thank you in advance Gregi