Search the Community

Showing results for tags 'got simple rs232'.

  • Search By Tags

    Type tags separated by commas.

  • Search By Author

Content Type

Find results in...

Find results that...


Date Created

Last Updated

Filter by number of...

Found 85 results

  1. Hello, I'm new to this forum and PLC world in general (especially to Mistubishi PLCs). I have a task in which I need to synchronize servomotor with another motor that runs conveyer (servomotor needs to stamp a label on a foil on a conveyer), in GX Works3. Servo motor is run by Simple Motion module. I need general tips on how to make pulses from encoder into something useful that can be used to send data to Simple Motion module. I need high speed counter to count pulses (never actually did this, I got this from manuals), how would I, for example, get speed out of it? Number n pulses, divide it with time it took to get to n pulses? How would I make Simple Motion to make servomotor on his Axis #1 to rotate at same speed?    
  2. Hi All I am new here without much experience of plcs. I have a PV 550 with DH485 coms port that I want to replace another PV550 with rs232 that communicated with an SLC 5/04. Is there some way to connect the two with a cable or protocol connector? Alternatively can you connect through the printer port on a PV600? CHeers   Azza

  3. FATEK Serial communication

    brian91 posted a topic in Other PLCs

    Hello everyone, I am completely new with Fatek PLC. Can somebody help me (example, tutorial, explanation) with a serial communication between Fatek and PC. I am using FBs series.
  4. I have a Micrologix 1400 and one PC which sends 102 Characters in RS-232. I need to read all characters with Micrologix 1400, Is there any way to read all characters? I know the limit of ARL and ARD instruction is 82 characters. I do not know if two ARD instructions could read all characters. Do you have any experienced like that? Could you help me? Thank you in advance
  5. Hi, there, I'm totally new to OMRON PLC, right now I'm using CP1H PLC have two CP1W-CIF01 on it 1st CP1W-CIF01 set as 115200, 7,2,E, Host Link, station 0 connected to Pro-Face HMI 2nd CP1W-CIF01 also set as 115200, 7,2,E, Host Link, station 1, I want to use this COM to talk to my PC that I can run vb.net program to monitor the bit and set the bit value. can you guild me how to start this project? thank you very much! Chen

  6. Sending Ascii from PLC

    remspot posted a topic in CX-Programmer

    I have an omron cp1le plc and a sato s84ex printer I need to learn how to send print jobs to it. I know I can use the Serial card option and send the code to the printer over RS232. I am using the NiceLabel software and printing to file which extracts the SBL code. That is where I am stuck. What part of the code do I use and where do I put it in the CX-Programmer. And what instructions should I be learning to send Ascii to the printer. I am very new at all this and just want a few hinters and direction. Thanks.
  7. Hello Everyone, I want to have a serial communication using Siemens S7-1200 with CM 1241 (RS-232) and communicate with my Arduino. Here is the setup of the communication. I have 2 temperature sensor and one Led connected to my Arduino, and on the PLC side I have S7-1200 from Siemens and CM-1241. Arduino and my PLC are connected just by using Tx and Rx pin no handshake is done. I am sending the temperature data from both the sensor to the PLC. on the PLC side i decide when to turn on the Led connected to my arduino depending on the different temperature values. I have assigning a ID to both the sensors before sending out the data. This is how the transmitted data from Arduino looks like $AOPT_TEMP1_20_TEMP2_21 . So far its good, I am receiving serial data on my PLC using RCV_PTP (received data are placed on the buffer) and sending data using SEND_PTP. I have also implement a filter on the PLC which will only accepts the serial data starting with '$AOPT_'. Now, I want to receive the temperature value from two temperature sensor TEMP1 & TEMP2 and then control the Led. For instance if (TEMP1>TEMP2 ) then turn ON the Led else turn OFF. I am able to receive the data on the PLC from Arduino but now I don't know how to proceed with comparing the received information. How do i extract the only required data from the received buffer? Any suggestions will be highly appreciated. Thanks in advance....

  8. Connect OMRON CJ1H to GSM modem

    AlexCyril posted a topic in CX-Programmer

    Hello guys, actually I am new to this Omron PLC. but i have small project to transmit a command to the GSM modem via the RS232 port so it can trigger the modem to send text msg. Can you show me the steps/guide/sample program to accomplish this program coding? I already read some topic in this forum regarding to this PLC RS232 port but still cant get the ideas when to create the ladder program. PLC Type : CJ1H (CPU65H) - RS232 port First input to trigger the GSM send text msg: AT+CMGS="+YOUR HP NUMBER" Second input to trigger GSM send text msg: YOUR TEXT MSG CONTAINS (Ctrl+z to send) Many Thanks, AlexB
  9. I have the following situation; I have a distribution network connecting about 400 RTUs, using 101 protocol to connect to their PDH MUX, which data slot is transported using SDH STM-1/4, to the Primary Substations. Then the primary substations connect to the LDC building using STM-16. At the Control Centre Building where the Front End is located, there is a STM-16 node with some PDH ports, but definetly not 400, so how can I extract this 101 asyncronous data channels to connect them to the SCADA Front End? Note that conversion to 104 is not allowed by the client. Thanks in advance!
  10. I need a Sample Simple Project to download . with Unity Pro XL and M340. Water treatment plant with pumps and mixer. Please Helpppppppppppp. My Email is : Shararehmirbagheri@yahoo.com