Search the Community

Showing results for tags 'double integer'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 8 results

  1. Binary outputs RSlogix 5000

    I am working on something different. I have a Signal Speaker that uses binary inputs to play a certain song based on source configuration. I have to send 24v to the inputs of the speaker. I have 5 of them with 30 different configurations. I am currently trying to do this in ladder logic, RSLogix 5000. Steps done. 1. Assigned the 6 outputs tag names. This is so that I can shift the program to other machines if I have to and I just need to change the slot location, or if I have an output go bad I can move it with ease. This works. 2. I  created the 30 lines of  5 columns to match the binary method. This works.    a. I can manually toggle the output to cycle thru the binary table. 3. Currently working on the logic that when a particular alarm is activated... I turn on the outputs needed to match the binary table. The problem is destructive bit reference on the coils.  I was researching some but don't know what direction to go. How can I call the same output on different rungs? I have attached the .L5X to show what I have programmed. 4. I know the first rungs are wrong. That is what I am trying to fix. 5. Would there be a better way to address this, if so how? Any help would be greatly appreciated.     Speaker_Alarm.L5X Speaker_Alarm.L5X
  2. Hello, I am trying to have single press and double press etc. functionality in my PLC program where for example, single press will turn on the motor whereas double press will turn on the motor for 5 seconds. Is it possible to achieve using ladder logic in sysmac studio, if yes, how? Thank you in advance.
  3. Dword to Float on FX3GE

    Hello! I have a float number (HEX: 3CA01D0F) in Big Endian. It's 0.0195451062. I get it from the sensor and store it in a double word variable. Could you help me? How can I convert DWord to Float? If i use DFLT instruction, It treats DWord as an integer (1017126159) and just gives me 1.017126 e+009 Thanks in advance.
  4. Hello, I'm using RSLogix 500 application for LAD programming. I would like to convert the float data type to integer data type and vice versa. I tried with the COP instruction as some had mentioned in other forums, but it was not working. So any suggestions on solving that issue would be helpful.
  5. real to integer number

    Hello, Could somebody give for me advice how need seperate real number to integer? for example I have in D10 real number 10,9 for me need to do integer number 10 and 9. The real number seperate to integer I am using this LADDER line, attached picture. In D90 I got 10, But how to isolate the number of decimal places,I can not think of. Please help for me
  6. Hey everyone first post on here, does anyone know if it is possible to convert a string into a double integer. i am working with a dimensioner and it is sending me its box dimensions in a 12 char string (see attached picture). however i need this data as a double integer (it seems to just take the string length not the string value i have tried both dim_lengh and dim_length.data[0]). i have gotten it down to the point where i have the string split up into the dimensions i need but i dont know how to do the conversion. (box dims for reference are 21 X 15 X 14.8) Thanks in advance, Dr. Brule  
  7. I have a problem with converting a server word. I'm trying to put the seconds in my program trough %SW50. But this is counting like this: 0000 0111 = 7 0000 1000 = 8 0000 1001 = 9 0001 0000 = 10 0001 0001 = 11 But i forgot how this is called. How do i convert this to: 0000 0111 = 7 0000 1000 = 8 0000 1001 = 9 0000 1010 = 10 0000 1011 = 11 And is this second style integer?
  8. I have 14 alarms all addressed to word 200 i.e. 200.** and i want to monitor the state of bits in word 200 such that if one of them is on the coil 204.00 should turn on (Currently i am using the OR operator to turn on bit 204.00 but the task is to use a single instruction to monitor the sate of the 16 bits of a word by comparing it to an integer say #0). I was thinking of using compare to achieve this but i do not know how to compare a word say 200 to a an integer value #0 such that if DW200>#0 then 204.00=on. How can i achieve this and what instruction can i use, am new to omron plc's and am using syswin 3.4 and plc CPM2A. Any help or sample program to achieve the above is deeply appreciated.