Search the Community
Showing results for tags 'analog output fault'.
Found 161 results
-
I'm new to Omron, and after several days of diving into manuals trying to figure this out on my own and giving myself a headache I've come to accept that i need help. my task is the following: Control of the discrete and analog inputs/outputs in a DeviceNet system using an Omron CJ1M PLC’s and PT’s. Use at least one thermocouple, one analog input, and one analog output for the DeviceNet network. Use a pushbutton and a light for the start of the process and an indicator for the started process. I have a Drt1-Ad04 input, a Drt1-ad02 output, and a Drt1-ts04t temperature control. My devicenet is Cj1w-drm21, The Omron system itself is a cj1m-cpu13 etn21. I have node addresses for my input, outputs and temperature control, those being 35 for input, 25 or 30 for output and for temperature control 5, 15, or 20. The ip address im using for this project is 142.214.143.9I'm using Cx programmer, Designer and Integrator. On Cx programmer I've managed to create an IO table but i have no idea on how to begin the program or even get a current reading from my generator.On Designer I've made what i believe to be the layout of the pushbuttons, I just have no idea of what addresses to enter.And on integrator i'm having troubles on figuring out how to make a routing table. I've went through many manuals and either i'm missing something really basic here or I just have no idea on what I'm doing. The only advice I was given was to dive into more manuals and find my addresses for my inputs, outputs, and temperature or to find the information from an outside source be that a forum or customer service. I am able to provide more information, and screenshots of what I have done if needed. Any kind of help would be greatly appreciated!
-
I am from AB world, but now am facing up with Omron PLC troubleshooting. One of my machines with Omron CQM1-CPU43 went out of work, because of low batteries in the PLC, program was lost and PLC stock with Error” Low battery” Is my luck, program was stored on EEPROM card, so I replaced the battery and reload program back to PLC, but after that other light on PLC comes up ”Output Inhibit Bit” is ON and all outputs are OFF. Operational manual sated just “turn back to OFF position, the “Output OFF Bit SR 252.15” and nothing else, where and how I can do it. I can not find in the CX programmer software the way to switch this bit, neither one rung in the program consist this bit, I really don’t know how solve this problem. Could you, please advice?
-
Hi Good Day, I need a suggestion, I have an omron encoder, encoder counter meter (K3NC-NB1A) and communication card RS-232C 25pins (K31-FLK1). My question is, what is the best omron software to read and manipulate the data from the encoder (I have CX-one software but I only use CX-programmer). I want to capture the encoder pulse and convert to velocity, acceleration, deceleration and also energy absorbtion. I have to use mathematical formula such as two times differentiation. I also need to show grapf and display final result that is energy absorbtion reading. Or is it much simple if I use VB / labview / java software? Thank you in advance
-
Hi everyone! I have this simple problem, but cant get over it. I have structured ladder/FBD Project and i use GX works2. As topic tells I use analog signal from field. Now, i need to compare this value X (from field) to Values X1 and X2, meaning if value X is between values X1 and X2 then M1 is true. Ok, but what function i need to use for this? Best regards, Juha.
-
1734-FPD needed between relay output module and analog input?
python01 posted a topic in Allen Bradley / Rockwell Automation
I am working on Remote IO panel and plan to use the following components: 1734-AENT 1734-OW4 - qty 2 1734-IE4C I wonder if I need to separate the bus between the relay output module and analog input module? Or anywhere else in this setup? Thanks. -
I have had a GE 90-30 CPU331 in my house for 17 years with no trouble at all. I have a problem that I have never seen before. I was editing the program using LM90. I don't know what I could have done in the program to disable an output. Just 1. All the rest of the points in that group on that card still work. I swapped cards with no difference. All of the elements of the rung are true (highlighted). The output is not on or highlighted. The nickname over the output has ONE letter highlighted. The bit in the reference is "0" and is highlighted or "grayed out" (the cursor is not on it). I searched for coil conflicts. I am using this output contact lots of places but only one output. The logic is working correctly when I use another output or %M. This is an isolated output which needs to be in this group (moving it would be awkward). What does a "grayed out" reference bit mean?
-
Hi all, Im new with plc programming and now I need some help. As topic says, I have FX3U plc and gx works2. Now, I need to tell stack heigth as positions by output. We all agree, that you can tell ten different situations when you have four outputs (Y1 and Y4 = position five). Is there any practical/ reasonable way to do this when you need use outputs. For example, is there any Functions for this, or? Best regards Ultra.
-
I need to set up D/A module. I have few questions. What is the difference between offset and gain setting mode? I would like to use range 0 to 10V which would have to be set as user range setting, can I do it using GX Works 2? Or do I have to use the GX Configurator-DA package?
-
Hi everybody, I am new in these issues and I have faced a problem that is driving me nut. I am building a mixing batch HMI and its PLC program. In my HMI I created an analog tag that stores and integer number. This tag is responsible to comunicate with an analog input of the PLC I/O expansion module, whose address is I:1.0. In my HMI I put a numerical input box to send values to this analog input, but every time I write a value in this box and press the enter key the numerical input box gets red and don't send the value to the plc. Appear the following error message "cause: Addressing problem or memory protect rungs" on the left botton corner of the HMI. Some pictures are annexed to describe better. Anybody knows what can I do? I am using PLC SLC 5/03 + Analog module 1746-NI4
-
Hi im quite new to Siemens programing. I got a issue that iwe been stuck with for a while now when im programing in Graph. When a supervision_fault happens the sequence is locked until I press ACK_EF and the transition is fullfilled. Then the sequence continues right on. What I want is that if ACK_EF is pressed the supervision fault will be cleared and the sequence remains paused until I press "Startbutton" again. I´ve tried Halt_SQ when the FAULT is triggered but I cant seem to get the FAULT down when I ACK. Also tried to switching it over to manual then ACK the fault. But that didnt work for me either. Hope there is someone that could help me with this :) It would be much appreciated!
-
Hi All, Im sure this has been covered before... Im using a ML1500 and a 4-20ma output flow meter. Due to the erratic flow in the line the analog signal is all over the place. What is the best way to smooth this signal out so I don't see all these variations..??? I don't have a CPT instruction on the ML1500 but there has to be a way. Just looking for the way you guys do this that gives you the best results. Thanks
