ABlearner
MrPLC Member-
Content count
70 -
Joined
-
Last visited
-
Thank you so much guys, the information what you guys shared are very useful. I made a little example program, to check how is it working. Its working properly I guess. @pturmel Could you please share with me an example ladder logic, about your solution. Some part of that dispriction is not clear to me yet. Thanks ahead.
-
Firstly, thank you for your answer! Secondly, yes they are the same size. Im trying to make the proper code for the task. I made in the first row, a signal when a bad product is detecting I raise a counter like 1, 2, 3 4. ... and so on. In the next row I check wether the counter is equal to 1 if yes, then I start to accumulate the pulses from the encoder until its reaches the 500, at that point I make a Stop signal, then I clear the counter. Of course there is a possibility, there is a new NG product can appear before the former one stored out, so if the Bad_product_appear bit is active again then the Counting counter isgoing to be 2 and it sarts to count also for the second, as the same way as before. My question is what if I have to make like 200 row like this, I think there is a better solution. Anybody can help this, if my explanation is poor Im sorry, I try to answer for every question. Thanks ahead.
-
Hello Guys! I would like to ask your help. I have a conveyor. At the begining of the conveyor i have a sensor which is declare wether a product is good or not. After that 5 meters i have to store out the bad product. In the exact place i have to stop the cv and store out. I have an encoder on the cv so i can calculate the correct position. The only problem is i have to write a tracking because i cant know when will the next wrong product coming. I could make some calculation making couple hundred rungs but its not sounds workable. Thanks ahead for any help.
-
Hi! A have a question about how can I send the current User data from the Panelview (HMI) to the PLC. Its an allen bradley PLC 1756 L71. In the Factory Talk view I tried to make a register and to move in it the current user, but unfortunatelly its not working. Is anybody here who can help me with this ? Thanks ahead. Br.
-
Hello Guys. Is it possible to use an fr-a840 to use in the same time positioning control and also in speed control mode ? In the moment the vfd is in speed control mode. But now i also have to need to stop the conveyor in certain position. It will be a new feature. If its not possible, do i need a hsc ? The speed of the conveyor is 20 m/min and the accuracy should be within 3 mm. Could anybody help me with this. Thanks ahead.
-
Hello Guys. Is it possible to use an fr-a840 to use in the same time positioning control and also in speed control mode ? In the moment the vfd is in speed control mode. But now i also have to need to stop the conveyor in certain position. It will be a new feature. If its not possible, do i need a hsc ? The speed of the conveyor is 20 m/min and the accuracy should be within 3 mm. Could anybody help me with this. Thanks ahead.
-
Thank you for the thorough answer. Lets assume the drive cant do it. In this case do i need an encoder on the conveyor ? The conveyor maximum speed is 20 m/min. In this case do i need a high speed counter module too in the plc ? The precision should be within 3 mm. Thanks.
-
Hello thank you for the answer. Yes i have an encoder on the the conveyor motor. Is it enough ? Or do i have to apply also an i dependent one on the conveyor directly ? Thanks.
-
Hello Guys, I have a Mitsubishi A8000 series vfd with an encoder card and also encoder. With analog (0-10V) signal i can read back the current speed. The conveyor convey paper sheets. Occasionally they change the width of the paper but the the two type of paper is connected. We have a camera on the begging of the conveyor, and we would like to lets say cut it 2 meter later. But the position should be very precise otherwise we are not cut it in the good position. The cutting procedure would happen also an asynchronous motor or with servo motor. Is it possible to write a tracking program and cut paper sheet in a good position ? My plane is to stop the CV in the position and waiting for the cut and go on. The plc is Allen Bradley, control logix 5580. Any tip would be appreciated. Thank you so much.
-
Hello Guys! I have a problem what I can't really solve. In factory talk view (10.0) I wanna use a momentary push button. When I start the project, and I click on it nothing happening, the button activate only when I release it. Its like there is an OSF instruction inside. I want the button activate until I push. May I use a wrong button ? Could you guy please help me with this? Thanks ahead.
-
Thanks for the feedback. The encoder is sew ES7C/AA. TTL/HTL encoder. So actually none of them. Its a push pull output encoder. The option card type is FR A8AP. So if i can get position then how ? I already use the inverter to read the speed of the motor. Thanks ahead.
-
Hello guys. I have a question, i have a mistubishi fr-a800 vfd with an encoder option card. On the motor we have an encoder. I can read back the speed with the plc with analog signal. But can i use also for, tracking the distance ? Can i set anyhow the inverter lets say after one round on the encder send some digital signal to the plc. Is there any chance to set it ? Lets say this is a conveyor, in this case its better if i put an encoder/counter on the conveyor and it will be directly connected to the plc. Thanks ahead
-
Hello, Thanks for the feedback. I think you wanted to writie VFD not VSD. No I don't need one more inverter. I would like to get one more safety output for my system. But in my understanding I have to attach an expansion unit to get one more. I read about more, beside connection of the EA, EB, EG, EP terminals, I have to connect the first modul's OUT terminal with the second's IN terminal. I still don't know, what should be, the inputs of the expansion modul ? Should I let the without connected ? Or should I use short cicuit between X0-COM0, and X1 - COM1, or I have to use the same inputs as used for the main module. Please guys help. Thanks ahead.
-
Hello guys! A would like to set up a new inverter for my existing machine. I wanna follow the recomandation about the safety wiring. The only problem is I need one more, Z safety output. I checked, there is official expansion unit, and it says I have to only connect the EA, EB, EG, and EP terminals ? Do I have to connect again the X0, COM0 ; X1, COM1 terminals, because I want actually the same inputs, just I need one more safety relay output. I attached picture about it, thanks ahead.
-
Hi, Do anyone knows what is the meaning of the following inverter nameplats characters ? FR-A840-00023-E2-60 Mainly the beginning with the FR-A. Thanks ahead.