Bob O
MrPLC Member-
Content count
482 -
Joined
-
Last visited
Posts posted by Bob O
-
-
What Mickey said. So was this a new unit out of the box from AB or just new to you? I am going to assume new to you because you had to press the comms button to get comms to work or do they come this way sometimes brand new? -
The 24VDC has nothing to do with comms so you are correct. Is this a new out of the box ML1200 or a new used one? In RSLinx did you select the AB DF1 driver and then select SLC Micro PanelView as the device? Also, what cable are you using for comms between the PC and ML1200? Here is a picture AB_DF1.pdf -
You could search the fault troubleshooting in the manual but I think the fault light out of the box will blink when no program is installed. Now for setting up comms. Do you have a real serial port on you computer or are you using a USB to serial converter? Hope this helps. -
Thanks for letting us know that you got it going. -
I am going to assume RSView32. RSLinx Lite will not work with RSView32 but you should be fine if you can use RS Linx Classic Pro. Hope this Helps -
I knew I would learn something. Thank you. -
I am prob going to learn something on this but can't they plug the card in and cycle the power? -
Hey Ken, Ex-Navy here I was an ASE stationed in Jax FL and at Cecil Field FL. -
Are you removing the card to replace it or are you removing it because you don't need it? -
Thanks to all that have replied. I am off to the customers this week and I'll let you know what they say. A week with no cell coverage or internet = middle of BFE. -
It is in its own pipe and there spec is to megger every conductor into the panels. I am going to assume they are wanting to check if any of the conductors were damaged during install. Thanks Again -
Rodney thanks for the reply. I searched omega before posting but didn't find the info I was looking for. Example THHN is rated at 600V so we test at 1000VDC and they have other cable that is rated at 300V and we test that at 500VDC but the TC cable isn't marked and they don't know what it should be tested at. Thanks Again, -
I have been searching for the voltage rating of type J TC extension wire [White/Red] this morning without any luck. The customer wants us to megger these and they don’t know what the rating is for their existing TC wire. Any help is appreciated. Thanks, Bob O. -
I would start by researching the channel configuration of the AI that you intend to use and the data sheet on your flow transmitter and also read the help file in RSLogix500 on the SCP instruction. Hope this help. -
how to rotate an object in RS view? I am assuming RSView32 but it should be similar in FactoryTalk also. Select object in graphics display > Click on Objects up on the tool bar > Select Rotate. See Attached Picture. Flow indication and totalizer simple calculations in 500? Maybe, can you tell us more about your application? Hope this helps. Rotate.pdf -
Not a FT expert but post the .apa file since that is the one you really want in the first place. Maybe someone with FT will look at the .apa file and help you. -
So wiring schematics are done before or after the panel is done or it doesnt matter. 1. Create Schematics 2. Build panel 3. Update prints for redlines. [ Redlines are errors or modification during the build ] 4. Ship panel with correct prints. 5. Send bill. Hope this helps -
Error = SP*1.1 or SP*.9. You could place these two values in a LIM instruction or put the SP*1.1 in a GRT and the SP*.9 in a LES. -
Post your program and IF I have time I can dump into a ML and see what happens. Edit ....Must post quicker..... -
Ron B are you part of the site that is linked above because if you're not they are using a lot of your hard work. -
Thanks. We do separate the 24 and 120 so this was probably more of a question just because it has always been done that way doesn't mean it should be done that way. -
I have an electrical installation question. Is it required to separate the ControlNet for communication, 24VDC for I/O and the 120VAC I/O into separate pipes when running from panel to panel? Thanks -
I am going from memory here but I don't think you can rotate the text in RSView32. -
Now the question: What is the best way to achieve my goal stated above? I am considering two options, but maybe you know of more: 1) Take 4 courses from Rockwell that will get me a "ControlLogix Programming Certificate" 2) Take Ron Beaufort's troubleshooting & programming courses JP72, I have been to some Rockwell courses in the past I can't say anything bad about them but I have also been to Ron's classes and I can honestly say that I would recommend Ron's classes above others. Hope this Helps, Bob O
Screen Colors for a distributed application
in Allen Bradley / Rockwell Automation
Posted