nguyenthanhcanh

Hello, I want to upload program from FATEK PLC VBs. Please help me. Thanks

Hello, Our customer has used a DeviceNet board for 3G3MX-A2004, board part number SI-N/V7. Pleae tell me possible to replace to new version 3G3MV-PDRT2 Thanks

If the file use Japanese font, must select Control Panel/Regional and Language Options/Advance --> select language in the drop down box --> restart your PC. Now, open the file you can read the comment in Japanese.

The part number of programming cable is PS1-SM14-RS232 but I need the diagram to make myself. Thanks

Hi, I need the manual for Festo PLC PS1 HC01F. Please help me. Thank you.

PMCR, Please send me too. Thank you.

Hello, I have configued CITECTSCADA web but the tag value don't show. Please help. Thanks

So possible to connect to C200H via IP006 + RS232/422 converter from CX-Programmer? Possible to connect IP007 to C120?

Hi, I know C200H-IP006 is used to convert peripheral port (48 pins) on C200H/C1000H CPU to peripheral port (20 pins) as same as CPM1/CPM1A, but I am not sure that posible to use IP006 for C120? Please give me a help. Thanks

Unfortunately, I have tried with NTSTV4.82 and NTSS2.33 (DOS) but cannot upload the program. Perhaps, incompatiable hardward version or system version?

Hello, Our customer has a machine using NT20S connect to Mitsubishi. Check System menu: Comm. Type: Com Link PLC: QnA I want to upload the program but NT20S (in NTST V4.82 support OMRON only). I check that NT20 support both OMRON and Mitsu (FX, A). So I want to ask I can select NT20 for uploading program? Thanks

Hi, I want to built a SCADA system with about 12 PLCs - FX2N and one A2AS CPU, a computer connect to these PLCs I'm not sure what FX2N adapter or module for communication can be used for FX2N system: 1. Communication module FX2NC-485ADP + Interface Adapter FX2N-CNV-BD or 2. Interface Adapter FX2N-485-BD The system aslo has a PLC A2AS CPU, so what communication adapter or module can be used here? I'm hearing from you. Thanks

Hi Friends, I have done successfully with some Proface GP HMIs, but with GP370-LG1, K-tag does not work: cursor not focus and keypad not show when touch on K-tag object. Please help me. Thanks

Hello, I want to make a network for programming and SCADA at the same time from control room. PLC is some PLC: AB SLC5/03, SLC5/04, SLC5/05 and MicroLogix1000, MicroLogix1200 Please advise me some configurations for the connection? Low cost is considerable. Thank you.

I have refered 2 modules from Prosoft: 1. EtherNet/IP to DF1 Master/Slave Gateway 5201/5202-DFNT-DFCM(4) 2. Wireless DF1 Master/Slave Gateway 6201-WA-DFCM How about these modules? Possible to online RSLogix software for program maintenence and SCADA software at the same time? If I use CITECT SCADA, what protocol will be selected, Serial (Half-Duplex DF1) or Ethernet (TCP/IP)?

Thanks

Hi, I want to add a CVM1 to the controller link network but in CX-Intergrator I cannot find any CPS for CVM1. So please help me how to config controller link network for CVM1. Thanks

If I have a CJ1M connected to some CVM1 and CS1H via Controller Link (Network #2). Host computer connect to CJ1M (as gateway) via Ethernet (Network #1). I know that I can use CX-P connect to CS1H pass through CJ1M with FinsGateway. But I'm not sure possible to connect to CVM1 pass through CJ1M? Please help me to make clear this.

Dear Friends, I'm planning for a SCADA project that PLC scan time directly affects to system respone (quick respone required). So pls confirm me that any influence of communication to scan cycle (apply to RS232 port, Ethernet, FINS command, ...)? Thank you.

Hello, I cannot install USB driver for NP touch screen on Windows Vista Pls refer the attached picture and help me resolve the problem. Thanks

Hello, I want to connect NT11 to printer. As the manual, need a printer EPSON ESC/P. I haved looked around on website epson.com but I cannot find any model supports ESC/P standard. So if you know, pls share me. Thanks

I have tested with EPSON LQ-300+II and it works fine.

I use Vista 32 bit and UAC is disabled too. CX-ONE (CP1H & CP1L USB driver) and Finsgateway 2003 work fine but NP USB driver doesn't work.

The communication works fine after change C078 to a number >0ms

Hello, Before I have worked with 3G3JX, Modbus is good even many mistakes in the manual. Now I work with 3G3MX but this inverter not work stable in communication. I have set all parameters C70s, A001, A002 (the same with 3G3JX) I test with Multiway (read 1W, register 0001h), comm with 3G3JX is good but not stable with 3G3MX. Pls see the attached image (comm with 3G3MX) and give me an advice. Thanks