MrPLC Member
  • Content count

  • Joined

  • Last visited

Everything posted by dekor

  1. Logo mem card

    Hi, did you switch off and try to start BM without memory cartridge ? Then was no program in BM? Try to copy and remove memory without power off. Was a password request when you copied the program?
  2. Logo mem card

    What I understood is that you did not copy the program from memory cartridge into LOGO BM (base module). 1. You need to copy program into BM 2. Connect your laptop and upload the program from BM into your laptop.Save-it into you laptop. 3. Modify the program as you need and download-it int o BM.   Attacheed you will find instructions about working with memory cartridge. Send me feedback about your progress.LOGO 6 working with memory card.pdf   It looks like I cannot attach the file. Please check next document from original link You will find necessary info on pages 203-215.
  3. Logo mem card

    Hi, I guess that the LOGO hardware that you have is an old version, lower than LOGO 7. I know that the same connector is used for programming and also to insert memory cartridge or battery cartridge.
  4. Logo mem card

    Hello Beny, I am a bit confused by your question:  You want to retrieve program from a battery cartridge? Or from a memory cartridge? My English is poor,  but I have some experience with LOGO and I intend to help you.
  5. Siemens S7-1200 & drives series in Labview

    Have a look on YouTube. Search for PC Simu . If you like them, then search for download link. It has drivers for Logo, S7 200, S7-1200,  S7-1500. Is free of charge. All you need is a password.  You will obtain free of charge just asking to creator by e-mail. His e-mail you will find on Help / About. This is only requirement. 
  6. PCMCIA Card (CP5512)

    One more think that you should know.  If you are using Microwin on Win10, then you must have SP9 installed. 
  7. PCMCIA Card (CP5512)

    As I wrote above: s7-200 has no MPI. Please,  check the system manual. PPI is the native for S7-200. ProfiBus is present only on few CPU, not all family has this  option. I suggest you to look for an USB PPI adapter.   
  8. PCMCIA Card (CP5512)

    No offence,  I asked if you are sure about communication with S7-200. Majority of S7-200 CPU don't has a ProfiBus port. MPI ? Never on S7-200.  My answer is based on your question.  I suggest you to upgrade to an USB adapter.  
  9. PCMCIA Card (CP5512)

    Are you sure that this adapter can be used in S7-200? Better you will look for an USB RS485 adapter. Make right connection on plc port side and you will solve this problem. 
  10. CM1241 send only zeros RS 485

    It seems that you mixed S7-200 with S7-1200. S7-1200 can  be accessed by Ethernet interface, not by RS485 ( you wrote RS458...). Try to explain again.
  11. Simatic C7-621, USB interface won't work.

    Hi, I suggest you to do a "repair" of Step7.
  12. op320-a communication

    Where is the connection between M0.0 and V0.0 ?
  13. op320-a communication

    Hi, Microwin dont know other operating panel than TD200. On other software that you use, you must select type of plc, method of communication (ppi, modbus RTU, ProfiBus...), plc address, communication rate, mailbox, .... Sometimes is necessary to create into plc program a communication function. Therefore you may need to set your port to communicate as Modbus, or RS232 ASCII, or something else according to your HMI. I never used OP 320, so I suggest you to check on manufacturer web page for examples. Good luck!
  14. op320-a communication

    Hello , Have you set correctly the address of PLC on HMI project? Communication rate also? Are those parameters mach on both sides? Add some screenshot with communication settings from both projects, PLC and HMI.
  15. S7-200 Communication Problem

    Should I understand that you succeeded? It Was communication port occupied?
  16. S7-200 Communication Problem

    As far I know, only Microwin with SP9 can workon win 10. CPU in stop is useful for situations when PLC use the port for communication with different devices. When is in stop mode, the port is released and you can communicate with him through Microwin.
  17. S7-200 Communication Problem

    Hi, 1. for Win10 you must use Microwin SP9 2. Add a larger screenshot of your computer 3. Did you select the right com port? 4. Did you select right communication rate? Usually 19200. 5. Try to put CPU in Stop mode using selector and try again to connect in stop mode.
  18. PLC Software recommendation ?

    Did you know APT from Siemens? It can be your best choice. Not so common, but excellent programming software for process control.
  19. OLD Siemens PLC

    Hi, You need Microwin software. To be able to run on Win10, I suggest you to instal Microwin v4.0 SP9. You need also PPI adapter, not MPI  as S7-300.
  20. Programming s7 300 siemens

    It is a network where different components of one equipment are declared available ( installed). Using the results from this network, the program will access functions related to installed components and will not access functions related to not installed components. It seems to be explanation in project also. Language is German.
  21. s7 300 AND WINCC flex

    If you want to use a "push button" or a "retentive button " from GUI to activate the output , you have to use a memory bit. You may not activate directly an output from WinCC, it must be trough a memory.  
  22. SIEMENS S7 200

    Hi, You must pay attention to number of the timer. I suggest you to read help for timers where is explained relationship between number of timer and function. Then you will solve very easy whatever you want.
  23. Flexible Sequence Control

    You may use instructions like JUMP or SWITCH.
  24. VFD Analog output to LOGO!

    Is your connection cable correct screened?
  25. VFD Analog output to LOGO!

    Seems to be ok the wiring. Did you set the I8 as analog input? How it looks the LOGO program?