khoi
MrPLC Member-
Content count
19 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Calendar
Everything posted by khoi
-
Hi everyone, I cannot connect to my CP1H-XA-40DT-D via CP1W-CIF01 and CIF11. Could you tell me to check if these 2 cards still working or not? Thank you. Khoi
-
Hi every one, I want to record temperature to DM of CH1H. At the first minute , data is save in D1. The next minute, data is saved in D2 and so on. How to do this? Thank you. Le Khoi
-
Hi everyone, I am working with CIF41, when I change IP address to 192.168.250.10 it is still working ( I can connect PLC) but the Err lamp on CIF41 blinking. I cannot clear it until I change it to initial IP address. Could you help me to clear the Err lamp? Thank you.
-
hi everyone, I created a program to indicate the motor directions, but it does not work. One more, I cannot reset the encoder. I used encoder#1. Pls help me. Thank you. MotorDirection.cxp
-
Hi everyone, I wonder if there are registers contains Lot No of C200H or CJ1M CPU. It is like A311, A310 of CP1H. Thanks
-
Hi everyone, I am looking for ST Guide Manual for Omron, I have not used it before. If anyone have it, pls send me. Thank you.
-
Hi All, I have a problem to work with negative numbers in CX Programmer. There is a sensor that measure from -50 to 150 degree ( 4-20mA) and I want to use SCL or APR to do. but I cannot type -50, it always asks the entered number greater or equals 0. Pls help me. Thanks.
-
hi everyone, I have a question on long word in PLC Omron. For example, D0=#1111, D1=#2222, D2=#3333. What is D1 value ( long word). Is it #22223333 or #22221111 or #11112222 ? Thanks for your reply.
-
Dear, I have a memory card HMC-EF183, 128MB and a CJ1M-CPU13. I did as attachment, but when I insert the card and switch on the dip switch 2, nothing happen. it is impossible to transfer program from card to PLC. https://instrumentacionycontrol.net/wp-content/uploads/2017/11/IyCnet_CS1_CJ1_FilestoFlashMemory.pdf Anybody can help me? Thanks
-
Hi everyone, I am a newbie and I was trained that Omron DM is not retained memory and I think it cannot hold data incase power off. But in fact, I find that DM can hold data if power off even if I remove the battery. Anybody can explain me more clearly. Thank you
-
Dear all, I have problem with the keyboard that connects to C200H-MD215 module in dynamic mode. I have turn on the dip switch No1. But if I connect Input to Output, I get up to 4 bits active ( normally only 1). Anyone can help me. Thank you
-
Hi everyone, I do not know the address of c200h-id217 and c200h-od219. There's a turnable knob on the module. Anyone can show me. Thanks
-
Hi everyone, How to change plc mode from RUN to MONITOR and vice versa without using CX PROGRAMER? Thanks in advance.
-
Dear all, I have a problem with my hydraulic drilling machine ( Furukawa HCR1500 EDII), that is equipped with CJ1M-CPU11 PLC. When it is working, it often stops because of 80CF/0F0F error . But when I remove all cables, it is normal. I change many PLCs, but get the same errors. Pls help me. Thank you. LE KHOI
-
Dear all, I have a problem with my hydraulic drilling machine ( Furukawa HCR1500 EDII), that is equipped with CJ1M-CPU11 PLC. When it is working, it often stops because of 80CF/0F0F error . But when I remove all cables, it is normal. I change many PLCs, but get the same errors. Pls help me. Thank you. LE KHOI error log.csv
-
Dear all, Pls send me some document on Omron memory area. I am a beginer. Thank you.
- 1 reply
-
1
-
Dear BobB, Sorry for my bad English. I want to back up an existing program to this EEPROM. Followings are my steps: 1. Turn off the Memory Protect switch of the EEPROM. 2.Open the program, switch off DIP2 of the PLC. 3. Power on the PLC, choose the Stop/Program mode. 4.Force SR270.00 to ON (value =1). 5. Download the program to PLC. 6. Power off the PLC. You can see the attached file ( written in Vietnamese) to get more info. Thank you very much. QUY TRÌNH NẠP CHƯƠNG TRÌNH VÀO THẺ NHỚ C200HW.docx QUY TRÌNH NẠP CHƯƠNG TRÌNH VÀO THẺ NHỚ C200HW.docx
-
Dear Sir, Could you show me step by step to write a program to a memory cassette ( eg C200HW-ME08K). I tried many times but failed. Thank you very much.