manna

MrPLC Member
 View profile  See their activity

  • Content count

    30

  • Joined

  • Last visited

Posts posted by manna

  2. Posted

    Dear All Members,

    I have Colmpleted Servo Programming in Q Series & Fx3u Series.Now I tring to use by Fx5u Module(build in Module).No any Additional Module like PG etc.now Can perform Postioning and OPR Program and Its works.But Problem Is I need JOG Program.and I dont Seen Any Demo Program In FX5u Postioning Manual.Is it possible to write JOG Program?Please Give me a Solution

    N.B. ------ (All Fx series) Have any Option to storing ABS Current data while Power plug out Then  plug in. i am Using SD 5502 memory to show current Servo data.data gone while replug the power.give me the solutions

    Thanks In advance 

  3. Posted · Edited by manna

    Dear All Members,

    I have Colpleted Servo Programming in Q Series & Fx3u Series.Now I tring to use With Fx5u Module(building Module).No any Additional Module like PG etc.now Can perform Postioning and OPR Program and Its works.But Problem Is I need JOG Program.and I dont Seen Any Demo Program In FX5u Postioning Manual.Is it possible to write JOG Program?Please Give me a Solution

    N.B. ------ (Fx series) Have any Option to storing ABS Current data while Power plug out Then  plug in. i am Using SD 5502 memory to show current data.data gone while replug the power.give me the solutions

    Thanks In advance 

     

    1 person likes this

  5. Posted

    i didn't connect with plc.need remote password.if i can communication successfully with PLC then i can reset the password as per your Suggestion .But I can't connect with plc.pls give me solution

       

  6. Posted

    dear All,

    I faced a problem that is password problem.I give a password on my fx5u Plc Couple of month ago.but I can't memorize this password.Have any Option Reset Data?i cant communication with plc.every time ask remote bpassword.Please Give the solution

     

    fx5u password.JPG

  8. Posted

    Dear All,

    I have a problem in MX Component (Communication setup Utility) Software.When I am going to setup This Software.Every Time Show Error Message.The Message is in  attached File. 

    I used FX 3G PLC.What i done that i given Bellow through the sequence by sequence______

     

    1.Click The wizard Button of Communication setup Utility.

    2.select logic station number.

    3.USB select

    4.Select FX 3G CPU

    5.Select Host Station

    6.Write Comments.Then Click Finish Button.

    but show the Error Message.

    Please Give the solution.Thanks In Advance. 

    mx-1.JPG

    mx2.JPG

    mx3.JPG

    mx4.JPG

    mx5.JPG

    mx6.JPG

    MX component.JPG

  15. Posted

    Dear All,

    I want To Inform U all That I faced A Problem about FX3u-ENT Module.When I Set Parameter(Ethernet Port Option) Of GXwork-2 Software.And Write To PLC.After Write PLC Show Alarm.like Parameter Error/Special Parameter Error.

    Please Tell me something About it.

    actually I want To Communicate FX3u PLC(Ethernet Adapter) to Weinview HMI via Ethernet Communication.and I want to Change  IP Address According To My HUB.PLC   default  IP-192.168.1.250 and I Want To Change to - 192.168.104.7(Approx).

    ent-1.JPG

    ent-2.JPG

  25. Posted

    15 minutes ago, Gambit said:

    Are you running the system in Absoluut or incremental mode ?

    Have you connected the battery in the MR-J ?

     

    Running in Absolute Mode.

    Both Battery Are  Okay.(PLC Battery And Amplifier Battery)

    16 minutes ago, Gambit said: