MIKE31
MrPLC Member-
Content count
173 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Calendar
Everything posted by MIKE31
-
HI EVERYONE What is the difference between regular step down 3 phase transformer with step down three phase auto transformer and what are the application. Thanks
-
HI EVERYONE Can please tell me what is the addressing: input o(zero) ch 8 bits input 1ch 8 bits output 10ch 8 bits output 11ch 8 bits Thanks in advance Mike
-
ALLEN BRADLEY SLC PROCESSOR 5/04 COMMUNICATION
MIKE31 posted a topic in Allen Bradley / Rockwell Automation
I have 5/04 processor and trying to communicate with processor but no luck DH+ and FAULT led are both solid red ,please see the attachment.Thank you so much DH_.doc -
migration panel view standard application
MIKE31 replied to MIKE31's topic in Allen Bradley / Rockwell Automation
Thank you for the reply and info. Mike -
migration panel view standard application
MIKE31 posted a topic in Allen Bradley / Rockwell Automation
HI I have migrated panel builder 32 application into factory talk view machine edition version 6.1 and I have problem . My problem is that screens numbers are not in order, First screen # is 1 the second screen is 12 the third is 6 and so forth. The FTVME does not allow me to correct the screens number based the original application in panel builder 32. Please let me know if you have had this experience and what would the correction method (if any), or it does not really matter if the screen numbers are not in order but application still would run on PV PLUS terminal. Thanks in advance for your time . Mike -
Thanks I meant pc not pv terminal .I have no problem with terminal regarding file deletion . Great help
-
I want to delete some *mer file IN FACTORY TALK VIEW MACHINE EDITION. I have created mer file of the same application with different names. I have looked some of the AB documentation as well as internet but so far nothing. Thanks for the help
-
HiI have already done as documented in Omron manual instruction and it is there and no question mark and no unknown devices.It is very strange that can not communicate with processor . What type of cable do you have ,mine is the one that commercially available in market (type B) . Thanks again
-
HI I have tried few times to go on line with SYSMAC CP1E PLC (usb termina). I have followed the manual , usb driver successfully installed but Communication with plc just keep failing. I have uninstall and install usb driver a few time but no luck with communication .I am running win xp with sp1. Any advice Thanks a lot.
-
hi I have installed usb driver correctly based on OMRON instruction on two laptops and results are the same with the message:FAILED TO CONNECT TO THE PLC. Is it possible that usb cable is bad and how to verify it. Thank you.
-
Failed to connect to the plc Thank you
-
HI How to see alarms bits and associates description in cx designer off line program. Thanks Mike
-
HI . Thanks for the reply. Mike
-
HI I did upload the NS program and the file is the same.My guess is that message is generated with with the stop command.How do see the all the messages (status or warnings) in NS .Thanks Mike
-
Thanks again you are right, it is quite possible that the ns program may not be latest version one. I will have access to machine tomorrow morning ,then I will upload it and let you the results.Mike
-
Thanks for the reply, I did follow your instruction but what I am getting is different than what I am seeing on off line mode.
-
HI how to write counter PV value as BCD in CMP(20) . Is it cnt 005 #230. I am not sure if this is right .Thanks for the help. Mike
-
Thanks for the reply. Mike
-
Thanks for the reply and information .mike
-
HI which method is preferable: 1- connect the devices (solenoid valves, contactor, lights, ........) direct to plc output using a fuse in series with it. 2- connect a relay directly to plc output and then activate the output devices by this relay . I have seen both methods mike
-
HI Yes obviously . As others mentioned I need Omron usb to serial adaptor or computer with serial com port. Thanks anyway Mike
-
HI I just noticed my desktop does not have any serial port so I bought a cheap serial to usb cable ( about 5 dollors) but I can not go on line using win xp. I did not have any problem with my previous desktop having serial port. Any advice . Thank you so much.
-
HI Thanks for the reply. you are dead right and you made me laugh
-
I hope someone will give some info in regards to following in Mitsubishi plc in comparison to AB plc : 1- Is M10 stands for internal bit ? 2- What is TO bit ? 3- what is it [set M11] ? 4- [pls M12] ? Many many thanks
-
HI GAMBIT Sorry but some more question. The pot you mentioned is it a time delay device to adjust time then what is the unit. Thanks again Mike.