GERRY JERESANO
MrPLC Member-
Content count
38 -
Joined
-
Last visited
-
Hello. I am new at Siemens Plc. My problem is after power interruption my S7 300 alarm BF 2 and BF 3 blinking And SF too. I reset the entire system but still BF2 and 3 still on blinking. What should i do. ? Thank you.
-
Cj2m-CPU31_ Allen bradley powerflex 525_Ethernet
GERRY JERESANO replied to GERRY JERESANO's topic in Omron
Good Day, Thanks for the inputs. I drive the Inverter tru terminal inputs. And set the frequency tru auto set up. 10hz,30,50, & 60hz. But i want to see the ampere or hertz in my pc in actual run. BSI or Ethernet is the connection. Thank you in advance -
Cj2m-CPU31_ Allen bradley powerflex 525_Ethernet
GERRY JERESANO posted a topic in Allen Bradley / Rockwell Automation
Hello, I have Omron plc specifically CJ2m-CPU31 connected to Allen bradley powerflex 525. I wonder what command should i use to drive the frequency inverter and to change the frequency at a certain time. Any body can help me. Thanks in Advance. -
Good Day, First time to connect Omron PLC to Allen Bradley frequency drive via ethernet ( POWERFLEX 525 ). I wonder what command should i use to start the inverter and change the frequency. I hope somebody can help me. Thank you in advance.
-
Send data memory from PLC to other PLC with CX Programmer
GERRY JERESANO replied to Amsterdamstyle's topic in CX-Programmer
Hello, I need to send data from plc 1 to plc 2. then send back to plc 1 one's i receive the data to reset or clear the data from plc 1. thank you. -
Send data memory from PLC to other PLC with CX Programmer
GERRY JERESANO replied to Amsterdamstyle's topic in CX-Programmer
hello, What if i am using 2 CJ2m-CPU31, PLC1 - Unit#0 - Node #2 - PLC2- Unit#6- Node#6 What should i put to may local and remote node of my rcv command. Thank You in advance -
Thank you for the replay, I am using ethernet connection. SEND and RECEIVE command is the only i should do. Am i right? There is no other setting in the plc to be set? Thanks in advance
-
Hello, Just asking a question. It is possible to communicate two plc ( CJ2M ) using cx integrator.? It is possible to exchange data between the two of them? Thank you,
-
Good Day, My situation is, I use CJ1W-SCU22 module to read data from my weigh-er. PT210EN - Baud Rate: 115200, 7.1 even Scu22 - Baud Rate: 115200, 7.1 even., Port1 Comm Mode: No protocol Protocol Setting : 1:1 protocol NO protocol Start code inclusion : NONE NO protocol End code inclusion : CR+LF I don't know why the RXDU command cannot read data from my weigh-er monitor. RD1 is rapidly blinking in the unit(SCU22). Any one can help? Thank in advance.
-
GERRY JERESANO started following CJ1W-SCU22 ver.2.1
-
finally i'm done, i got it. thank you.. I made my weighing scale into 2 decimal point.. Thank you.
-
Hello, Any body can answer me what happen why D103 does not convert but d104 is okay. d104 is the data of first digit + decimal of my weigh-er. D104 is the data of 2nd and 3rd digit of my weigh-er. D104 - Di= #0010, while d103 - Di= #0012.
-
Thank You Very Much, I understand now. I got it in a series of trial and error, Funny but effective. Thank you,
-
Good Day, Thank you for your support. But i don't know why HEX command doesn't response. There is no conversion output. I have a 9.6 kg load but no conversion has been done. What should i do? Thank you in advance.
-
Thank very much for your help, Just another question, How can i convert string data or do i have to convert the DATA ( string ) in to other form of data. Because i need to stop my pump in a certain load. Just an Example i have a 100 kg load at 90 kg the pump should stop running. Thank you in advance.