geoorge

Hello Friends There is a way to install RS LOGIX in my laptop, the problem is that i dont have any way to attach a floppy disk drive to my Laptop, and i can do the activation, Thanks in ad vance

Basically is just an example for my school boys, they want to know about grafcet, and the course is with AB SLC 505, but we are just programming in ladder logic

Team im looking for an example, with a grafcet chart and with the ladder logic for the same example please could someone help this poor guy regards

HELP !!!! I HAVE ON SLC 5/05 CONNECTED TO A PV USING DH485, ON BOTH EXTREMS OF THE NETWORK I HAVE TWO AIC INTERFACES, I HAS BEEN WORKING FINE FOR THE LAST 2 YEARS. YESTERDAY SUDDENLY IN THE PV IT SAID, ERROR 615 ERRORS ON THE DATA LINK, AND IT HAS THE COMMS LED GREEN FLASHING. I MADE THE "MEXICAN RESET" (I SHUTDOWN THE SLC AND THE PV) THEN POWER UP AND THE SAME ISSUE. SOMEONE HAS A TROUBLESHOTTING GUIDE FOR THE DH485. IN THE CHANNEL 0 CONFIGURATION OF THE SLC I SEE 0 NODES ATTACHED TO THE DH485 NET, I CHECK THE PHYSICAL LINKS AND IT LOOKS FINE. PLEASE HELP ME

I NEED TO SEND BIT STATUS FROM A MICROLOGIX 1000 TO A VB APLICATION, BUT I DONT HAVE AN ACTIVE X CONTROL, SOMEONE COULD SEND ME A SOLUTION PLEASE, ITS JUST ONE BIT, I DONT WANT TO BUY THE WHOLE ACTIVEX DRIVER PACKAGE REGARDS JORGE

I can someone know if there is a free distribution of the RSLinx ? please if u can upload the link thanks

Friends I am making a short course for my technician to teach them plc programming, someone can help me sending me an Allen Bradley Emulator. Thanks In advance !

help mee

Dear Friends, Im working in a manufacturing facility for GM, so i will review the logic of my ladder in order to 1.- make clear, when to send the 259 or 260 value to de M0 in order to clear the transaction 2.- im going to place the Eurotherm controller as an Slave without master. attached you will find 1.- the rss file with the aplication example 2.- the eurotherm devicenet pdf file (note i have the 2200 controller) 3.- the devicenet file I hope that so meone will find a little time for help, i will apreciate any comment Dev_027506ENG_3.pdf RSS_Files.zip 659728.DNT

Sure Ken, See when i map (m0 30) the Eurotherm 4 output bytes i can only get the value of the temperature. In order to access to more values of the eurotherm i need to use explicit messaging, and send 6 words and get four, but i doesnot get the expected value 70 transaction ID 257 71 Port 00000000 00000110 Byte Size 6 72 Service (14) 00001110 00010110 MacID (22) 3606 73 Class 00000000 01100100 Class=100 100 74 Instance 00000000 00000001 Instance =1 1 75 Attribute 3 for example and i Get Transaction ID 257 81 Port 00000000 00000110 Byte Size 2 82 Service 10001111 00010110 MacID (22) 83 Value but the Value is always cero, no matter what shows the eurotherm display. there is one bit Scanner Input file I:6/15 in the SLC, and eurotherm says that i had to send a word with the value of 259 to reset the input, but i never goes low.

hi in the rslogix i have 361 as the size of the m0/m1 file is 361, but when i see the scanner in the rsnet in the scanner properties input and output, i only see m1:6.0-m1:6.149 i have the firmware version 4.026 for the 1747-sdn

see another issue that i have is with the eurotherm controller over device net, in my slc i try to get some values using implicit messaging, the i:6/15 never changes, i dont know if i have to enable some options in the 1747 scanner or somenthing, as far i know the m0 224 and m1 224 must be used, but in my ios list on the 1747 i only have values for m 0-160

Thanks ill try and let u know see another issue that i have is with the eurotherm controller over device net, in my slc i try to get some values using implicit messaging, the i:6/15 never changes, i dont know if i have to enable some options in the 1747 scanner or somenthing, as far i know the m0 224 and m1 224 must be used, but in my ios list on the 1747 i only have values for m 0-160

1 buck

HELLO GUYS I WANT TO OUTPUT SOME NUMERIC VALUES TO A TXT OVER ETHERNET EVERY 15 MINUTES EXAMPLE N10 ,N11, N12 OUTPUT WITH THE FILENAME YYYYMMDD-TIME.TXT THEN THE VALUES PLEASE HELP ME