Alibaran

MrPLC Member
 View profile  See their activity

  • Content count

    29

  • Joined

  • Last visited

Posts posted by Alibaran

  1. Posted

    hello guys

    I am going to do  the parallel link 2 plc's of model FX3U.I studied carefully User Manual Communication but I have a problem ,I don't have software(FXGP/WIN) which be connect me to the plc for setting of the communication rs485 adp.

    Even,i too searched to find it but never did see anythings . Can someone to help me for resolving problem?

    Thanks a lot to accompani me

  4. Posted

    On 11/2/2021 at 5:08 PM, photovoltaic said:

    You can make an axis with the PG0122 as the output. Connect this to the Yaskawa drive for pulse train control.

    The Omron servos you see listed are likely the EtherCAT Servo Drives.

    thanks.my problem did solve

     

  5. Posted

    On 10/26/2021 at 7:38 PM, photovoltaic said:

    The PG0122 has IOV and IOG exposed, so you could feed it directly from the card. I always prefer a PF card though - pretty cheap insurance. 

    how can i plus servo yaskawa into part servo draive  ?   because there isnt servo yaskawa into part servo and there is only omron servo 

  8. Posted

    hi

    can i connecting cpu nx1p2 with only unit nx_pg122 ,for each servo ,for example the servo yaskawa ?

    i should use ethercat ? or  ido not need, i can use Hardware unit nx-pg1222 for setting up servo And programing (asix_Mc-power ,Mc,,,)?

    of caurse, i cant use ethercat   !

    thanks

  14. Posted

    On 1/29/2015 at 8:11 PM, brk_h said:

    Is there any setting in EJ1N-TC4 that can stop the control output when there is an alarm on any of the channels? I'd like to stop the controller when Loop Burnout Alarm is detected on any one of the channels. Currently, I'm monitoring the status bits from the PLC side and sending a stop signal to EJ1 controller when its alarm status indicates there is an alarm. I'd prefer EJ1N to stop itself when there is an alarm. Thanks.

    yes.there is setting .you can cheng error alarm by cx thermo

  16. Posted

    On 1/29/2015 at 8:11 PM, brk_h said:

    Is there any setting in EJ1N-TC4 that can stop the control output when there is an alarm on any of the channels? I'd like to stop the controller when Loop Burnout Alarm is detected on any one of the channels. Currently, I'm monitoring the status bits from the PLC side and sending a stop signal to EJ1 controller when its alarm status indicates there is an alarm. I'd prefer EJ1N to stop itself when there is an alarm. Thanks.

    can you help me? about ej1n

  19. Posted

    10 hours ago, Gambit said:

    I know Mitsubishi EU made some FB for the ENET module to connect to ENET ADP via MC protocol.

    But you'll need to make an account to download them 

    this is to hard,dear mr gambit

    this is to hard,i never know it.please help me:-(

  20. Posted

    On 4/1/2021 at 10:39 PM, Crossbow said:

    FX3U-ENET-ADP connects on the left side of the PLC, and is basically a serial to Ethernet adapter.  It's primary use is programming over Ethernet.

    FX3U-ENET is used for controller networking and HMI connection. 

    FX3U-ENET-L is a lite version, it was not sold over here so can't tell you what the differences are.

    but i connected 2hmi with fx3u-enet-adp

    however i dont know how use the fx3u-enet-l and how configuration and how programing with module.of course i readed manuall fx3u-enet-l but i dont know >

    thank you so match,dear  crossbow

  21. Posted

    On 3/30/2021 at 1:26 AM, Crossbow said:

    The manual for the FX3U-ENET clearly indicates how to share data between PLCs.

    Thankful....

    I have a question?

    What is the difference between a module FX3U-ENET-ADP and a module FX3U-ENET-L?

    In fact, when the module FX3U-ENET-ADP and when the module FX3U-ENET-L is used?

    Thank you so much

  22. Posted

    On 3/22/2021 at 0:10 PM, Gambit said:

    Well this is not really possible.... They don't support fixed buffer/socket communication. you will need an FX3U-ENET module for that.
    But if you need to share data between them and it doesn't require fast speeds than you can let the HMI do it.
    Take a look at "Device Data Transfer" in GT Designer 

    Can you teach me?
    How to configure the module FX3U-ENET with PLC FX3U?

    And how to network 2 PLCs together and be able to control the inputs and outputs of each PLC?

    thank you very much

  23. Posted

    2 hours ago, JustinSmith said:

    You would want to use serial communication. My only experience using the enet-adp is sending read requests from an IQ-R plc to the enet-adp. 

    yes.thank you so much

  25. Posted

    On 3/15/2021 at 10:55 AM, Gambit said:

    The settings are described in the connection manual. Check this first if you have any questions after you can post them

     

    I was able to connect hmi 👌

    Thanks for your guide