Alibaran

Fx3u-enet-adp connect hmi

14 posts in this topic

Hi my friends.how can i connect the fx3u-enet-adp with hmi gs2110? 

Thanks 🙏🙏

Share this post


Link to post
Share on other sites

The settings are described in the connection manual. Check this first if you have any questions after you can post them

 

1 person likes this

Share this post


Link to post
Share on other sites
On 3/15/2021 at 10:55 AM, Gambit said:

The settings are described in the connection manual. Check this first if you have any questions after you can post them

 

Hi gombit dear, I have another question, sorry if my English is poor یhow i can 2plc fx3u ethernet connection together with fx3u-enet-adp? 

🙏🙏🙏

Share this post


Link to post
Share on other sites
On 3/15/2021 at 10:55 AM, Gambit said:

The settings are described in the connection manual. Check this first if you have any questions after you can post them

 

I was able to connect hmi 👌

Thanks for your guide

Share this post


Link to post
Share on other sites
On 3/19/2021 at 3:43 PM, Alibaran said:

Hi gombit dear, I have another question, sorry if my English is poor یhow i can 2plc fx3u ethernet connection together with fx3u-enet-adp? 

🙏🙏🙏

Well this is not really possible.... They don't support fixed buffer/socket communication. you will need an FX3U-ENET module for that.
But if you need to share data between them and it doesn't require fast speeds than you can let the HMI do it.
Take a look at "Device Data Transfer" in GT Designer 

Share this post


Link to post
Share on other sites
On 3/22/2021 at 0:10 PM, Gambit said:

Well this is not really possible.... They don't support fixed buffer/socket communication. you will need an FX3U-ENET module for that.
But if you need to share data between them and it doesn't require fast speeds than you can let the HMI do it.
Take a look at "Device Data Transfer" in GT Designer 

Can you teach me?
How to configure the module FX3U-ENET with PLC FX3U?

And how to network 2 PLCs together and be able to control the inputs and outputs of each PLC?

thank you very much

Share this post


Link to post
Share on other sites

The manual for the FX3U-ENET clearly indicates how to share data between PLCs.

Share this post


Link to post
Share on other sites
On 3/30/2021 at 1:26 AM, Crossbow said:

The manual for the FX3U-ENET clearly indicates how to share data between PLCs.

Thankful....

I have a question?

What is the difference between a module FX3U-ENET-ADP and a module FX3U-ENET-L?

In fact, when the module FX3U-ENET-ADP and when the module FX3U-ENET-L is used?

Thank you so much

Share this post


Link to post
Share on other sites

FX3U-ENET-ADP connects on the left side of the PLC, and is basically a serial to Ethernet adapter.  It's primary use is programming over Ethernet.

FX3U-ENET is used for controller networking and HMI connection. 

FX3U-ENET-L is a lite version, it was not sold over here so can't tell you what the differences are.

Share this post


Link to post
Share on other sites
On 4/1/2021 at 10:39 PM, Crossbow said:

FX3U-ENET-ADP connects on the left side of the PLC, and is basically a serial to Ethernet adapter.  It's primary use is programming over Ethernet.

FX3U-ENET is used for controller networking and HMI connection. 

FX3U-ENET-L is a lite version, it was not sold over here so can't tell you what the differences are.

but i connected 2hmi with fx3u-enet-adp

however i dont know how use the fx3u-enet-l and how configuration and how programing with module.of course i readed manuall fx3u-enet-l but i dont know >

thank you so match,dear  crossbow

Share this post


Link to post
Share on other sites

Posted (edited)

I know Mitsubishi EU made some FB for the ENET module to connect to ENET ADP via MC protocol.

But you'll need to make an account to download them 

Edited by Gambit

Share this post


Link to post
Share on other sites
10 hours ago, Gambit said:

I know Mitsubishi EU made some FB for the ENET module to connect to ENET ADP via MC protocol.

But you'll need to make an account to download them 

this is to hard,dear mr gambit

this is to hard,i never know it.please help me:-(

Share this post


Link to post
Share on other sites

start with creating a mymitsubsihi account on eu3a.mitsubishielectric.com

Share this post


Link to post
Share on other sites
On 4/8/2021 at 10:57 AM, Gambit said:

start with creating a mymitsubsihi account on eu3a.mitsubishielectric.com

yes.thanksful

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now