Amogh
MrPLC Member-
Content count
29 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout Amogh
-
Rank
Sparky
Profile Information
- Country India
-
Mitsubishi FX5U And VB.net Communication using TCP-IP Ethernate
Amogh replied to Amogh's topic in Mitsubishi
I have decided to use the Socket communication to communicate FX5U-32M with my PC The question is can i write D-resistor or holding resistor with this or I can just read data through it. Thanks Once Again -
Mitsubishi FX5U And VB.net Communication using TCP-IP Ethernate
Amogh replied to Amogh's topic in Mitsubishi
What are the settings to be done in FX5 can you share a link of any vb program so that i refer it Thanks Once Again -
Thanks in Advance I have Mitsubishi FX5U-32M PLC, I want to communicate it with computer to read and write resistor on vb.net using TCP-IP protocol. What are the settings need to be done, Is there any predefined library other than mx-component that i can use
-
Again thanks Should i have to create communication protocol to work this Another thing if i am using NonProcedure method with RS232 should i have to use "PLC LINK FLOW CONTROL TOOL" And commend i want to write is written in macro tool it should at the top of flow or just above "ECM SEARCH TOOL"
-
but according to Omron FH-L550 Camera controller datasheet mitsubishi PLC link is only applied to Q series PLC i had FX3G 40 MR I made connection using RS232 Will it be possible using this
-
Plc is mitsubishi Fx3G40mr Camera controller is Omron FH-L550 Camera controller The serial communication has been established and plc is receiving data from cam controller if data output tool is used But if i want to write some values from plc to cam controller how can i do it. Specifically i want to write coordinates of X and Y In ECM Search tool and set Master to those values.
-
Thanks in advance 1. I am using Omron FH-L550 Camera controller 2. I want to write data from plc to cam controller through serial Rs232 port. 3. The serial communication has been established and plc is receiving data from cam controller if data output tool is used 4. But if i want to write some values from plc to cam controller how can i do it. 5. Specifically i want to write coordinates of X and Y In ECM Search tool and set Master to those values. what is procedure to do it. Any help will be appreciated
-
Thanks in advance I am working with Mitsubishi Fx3G 60MR I want to communicating with MODSCAN SOFTWARE using Modbus RS232 Communication Is established i want to read and write Y0 to Y7 in it when i search in manual address is given is 0x3300 to 0X337F when i checked it shows nothing i have tried hex of 3370 nothings there so what decimal address is of Y0 and same for X0, M And D. Is there any table because i want to insert decimal values of address instead of hex any help will be appreciated
-
Thanks in advance I am working with Mitsubishi Fx3G 60MR I want to communicate it with scada which is having inbuilt Mitsu protocol written in it For the baud rate of 9600 it connects automatically but if we increase the baud rate error occur i want to communicate it with 38400 communication parameter for that is - 7,even,1 what setting can be done to achieve it any help will be appreciated
-
Thanks for the help in advance i am using mitsubishi fx3g-40mr plc 1] i am reading data from camera on serial port. The data camera send is ASCII character if camera send 0 i receive 48 if it is 9 i receive 57 which i under stand but when camera send 00 i receive 12336 and for 01 it shows 12592 it increment by 256 Please some one would tell me 2] And if camera send 000 the data receive is 12336 in first resistor and 48 in other is there some command which i can use directly for this conversion or any other type any help is appreciated
-
yes now its working properly very help full if you tell me factor K176 in FROM command and K304 in TO Command. i found that command in one of the sample programs
-
I have to connect one input and one output card to my master plc but when i connect it in sequence of [power supply][cpu][cclink][input][output] it gives error and i cannot on my output card when i change my sequence to [power supply][cpu][input][output][cclink] it shows parameter error 3105 c112 what changes has to be done to work both properly thanks for the help
-
ok in slave for read and write i am using "to" and "from" command photo is attached i just explain the factor K176 in FROM command and K304 in TO Command.
-
Thanks for all the help when i connect another Slave Plc Cpu is FX3G40MR Slave Plc CClink Card is FX3U-64CCL to my network where should i find received and send data in master Settings are done same in master no of station to 2 and quadruple for slave station switch is on 9 and station no switch is on 3