pv550
MrPLC Member-
Content count
63 -
Joined
-
Last visited
Posts posted by pv550
-
-
but he forgot the password.... what will we do?
-
Hiiiiii everyone.....
I have panelview plus 600HMI. I have taken the backup files from the hmi. To view the hmi backup file, i go with application manager software. It requires password to restore the runtime application. but i don't know the password which was created during runtime application. how to find the password.....pls help me..
-
B&R
in Other PLCs
Hello
I am having B&R hmi PP41 and PVI TRANSFER TOOl. I need to upload the backup and also i have communication module. I want to know the cable pin out for pc to hmi communication and also method for communication. Dip switches are in my hmi. Is any changes are done in the dip switches fro uploading the project. Pls rply me.
-
i am using firmware 5.10. for reloading firmware i need to go to configure screen. but i have 30 watch dog test stuck in booting screen.
-
Hello
I have panelview plus 600 hmi showing 30 watch dog test error. I searched the error in manual it says reload the firmware. but i need to go to the configure screen to set ip address then only hmi gets communicate and then i can able to load the firmware. How to reset the error?
-
FUJI
in Other PLCs
hello
I am having fuji ug221h-le4 hmi software v-sft5. I cant able to communicate pc with hmi. what is the pin detail for communication cable? How to take backup from the Hmi.
-
AB CAT 2711-T6C5L1 SER B REV F FRN 4.46 this is my panel view catalog number.
-
hello
I had another problem in pv 600 it shown 31 error. I read the manual that is stuck touch. I remove the touch and again it showing 31 error and i also change the new touch it again showing 31 error. how to solve the problem. Pls help me.
-
hello ,i have a panel view plus 600 in this him i can try to communicate with pc via serial port but isn't not communicate .plse tell me the detail how to communicated serial port via PC .
-
Hi
I am using wincc flexible 2008 sp3 to communicate with op77a. i write one tag in wincc flexible and transfer it to op77a. but when i try to communicate it with plc. It doesn't communicate with plc. I checked that address of the HMI and PLC are also same but it doesn't communicate. What is the problem? How to solve this?
-
hello
I have another problem in pv 600. When i download the program using panel builder 32 i had an error that showing Error 4003: Terminal destination memory error and in my display it shown file write access error. I cant able to download the program. what can i do to rectify the problem?
-
THANK U for ur reply
-
Hi
I have compact logix l23e-qb1b plc. In my plc run, i/o, ok, batt,Dcho all showing status red led on. when i connect the compact logix l23e with pc am using ethernet cable no indication is showing in LNK and NS and also MS red led on. later some time all red status will come to green status.that time cpu get communicated but doesn't show the symbol of cpu only shows yellow question mark. after 2 to 3 seconds it again goes to red status and communication cut. what is the prblm? what can i do for rectify it?
-
kaiser_will thank u for ur replay,
I replaced the touchscreen front face,but this fault is coming again.and the prior to the failure of the him touch curse move to up and down ,so i check this is touch problem is there but this is not a touch problem after i replaced the touch confirmation.
-
Thank u for the reply, I find the solution i changed dallas DS9034pcx. It worked out. Thank u once again.
-
hi everyone , i have allen-bradley pvplus 600 hmi ,this hmi coming the error is 3a Stuck touch.
i have tried to replace the new touch but this fault not clear coming again the problem,but i am confirm touch is good the problem is pv600 plus board ,plse anyone give an idea
-
Hi
I have a pv 600 display. I had the problem 32 error. That is real time clock test error . I change the dalllas but the problem still retain and my application also corrupted. i ill update the firmware but the fault remains the same. how to rectify it? what is the solution for the prblm?
-
hi guys ,
i have a mitsubishi gt2712-stba model hmi .how to upload the program this hmi to pc and which software use
-
thank u for ur reply
-
hi guys, plse help me
i have a mitsubishi plc fx2n-64MR WITH EEPROM .and my promblem is i want to download the program from pc to eeprom .iam using the software GxDEVELOPER. but this software not the option (program to load eeprom).how to possible mitsubishi plc eeprom program download.
Totally my promblem is :i wany to know how can i download a program from an FX-EEPROM mitsubishi plc model.
-
hi guys , plse help
I have a micrologic 1200 plc model number :1762-L40BXB . and i communicate this plc to hmi then i give the setting through hmi via .but that is not fix its erased the setting .so i and see what promblem ,that promblem is plc micrologic 1200 .so plse answer me.
Totally mt problem is setting erased.
-
yes, when i click backup it automatically goes to prosave for backup. prosave file is in .psb format. how do i get hmi file to edit the program. is it possible to make .psb file to hmi file??
-
HI
When i trying to connect panel view 600 HMI with RS linx software i have the error "fatal error initializing pic device driver" . How to rectify it?
-
I tried that also. when i press f1 button it cause error fatal 31. what shall i do?
E600
in Mitsubishi
Posted
I have E-DESIGNER V-7.52 software. When i choose new-> E600 it shows terminal version 6.1x. but i need to backup the E600 hmi which has the terminal version 6.01. What will i do?