minhdam06102
MrPLC Member-
Content count
23 -
Joined
-
Last visited
Posts posted by minhdam06102
-
-
Dear Mr, Thanks for your information. I used printer cable it is ok for PLC. best retards, -
Dear Mr/Ms, I using GT designer 3 to simulate have to use GX developer. But I can not install GX developer, just using GX works2. So Can I connect GX works 2 and GT designer 3 to simulate.. Please help me to slove this problem.. Thanks & best regards, -
Dear Mr/Ms, For that question I will answer as: Cable for programmer PLC not for touchscreen. I have already used Omron PLC program cable 4pin for PLC Q02H mitsubishi that work correctly and I program that now is OK. Cable R2 with USB that is another option for program QPLC. Mini usb cable use for HMI Thanks & best regards, -
Dear Mr/Ms, Anyone if you have link to RSlogix5000 please tell me. Thanks & best regards, -
Dear Mr, We use mitsubishi Q series Q02H, analog module is Q68ADI. for 2 panel is the same type but 2PLC not comment 0VDC and 24VDC. But if we not use analog separate( 1in to 2out) accessories. We just want to connect by wiring to reduce the cost. Would you please tell me how to do that. Thanks & best regards, -
Dear Mr, Thanks for your help. Best regards, -
Dear Mr/Ms, I have an ultrasonic sensor with 4-20mA analog signal output. But I have 2 control panel with 2 PLC separate, two PLC have analog input module . Can I send signal for 2 analog module of 2 PLC with one sensor? If can how can I make them - Analog signal will connect analog (+) and analog (-)with module analog of 1st PLC and then from that terminal (analog terminal of 1st PLC) wiring to analog (+) and analog (-) of 2nd PLC ? or - Analog signal from sensor (+) will connect with (+) analog 1st PLC then (-) analog of 1st PLC will connect with (+) of 2nd PLC then (-) 2nd PLC will connect with (-) sensor ? or - Analog signal from sensor (+) will connect with (-) analog 1st PLC then (+) analog of 1st PLC will connect with (-) of 2nd PLC then (+) 2nd PLC will connect with (-) sensor ? Would you please help me to solve this? Thanks & best regards, -
Dear Mr/Ms, I have an ultrasonic sensor with 4-20mA analog signal output. But I have 2 control panel with 2 PLC separate, two PLC have analog input module . Can I send signal for 2 analog module of 2 PLC with one sensor? If can how can I make them - Analog signal will connect analog (+) and analog (-)with module analog of 1st PLC and then from that terminal (analog terminal of 1st PLC) wiring to analog (+) and analog (-) of 2nd PLC ? or - Analog signal from sensor (+) will connect with (+) analog 1st PLC then (-) analog of 1st PLC will connect with (+) of 2nd PLC then (-) 2nd PLC will connect with (-) sensor ? or - Analog signal from sensor (+) will connect with (-) analog 1st PLC then (+) analog of 1st PLC will connect with (-) of 2nd PLC then (+) 2nd PLC will connect with (-) sensor ? Would you please help me to solve this? Thanks & best regards, -
Dear Mr/Ms, I have an ultrasonic sensor with 4-20mA analog signal output. But I have 2 control panel with 2 PLC separate, two PLC have analog input module . Can I send signal for 2 analog module of 2 PLC with one sensor? If can how can I make them - Analog signal will connect analog (+) and analog (-)with module analog of 1st PLC and then from that terminal (analog terminal of 1st PLC) wiring to analog (+) and analog (-) of 2nd PLC ? or - Analog signal from sensor (+) will connect with (+) analog 1st PLC then (-) analog of 1st PLC will connect with (+) of 2nd PLC then (-) 2nd PLC will connect with (-) sensor ? or - Analog signal from sensor (+) will connect with (-) analog 1st PLC then (+) analog of 1st PLC will connect with (-) of 2nd PLC then (+) 2nd PLC will connect with (-) sensor ? Would you please help me to solve this? Thanks & best regards, -
Dear Mr, I have an cable for Onron PLC ang HMI as picture below. Can I use it for Q02H CPU? Please hep me to know that? Best regards, -
Dear Mr, USB port but I dont know model for cable? Please tell me if you know!. Usually i use SC-06 cable-USB. But now i dont have it. Best regards, -
Dear Mr/ Ms, I have a Q02H CPU and GX works software. If I want to connect them and without SC-06 cable how can I do. But I have cable use for Omron PLC I can use for Mitsubishi? I can How can I download driver for cable? Please help me to slove this!!!! Best regards, -
Dear Mr Sparky, Thanks for your help. I see some structure so i will try it. Best regards, -
Dear Mr Sparky, But CP1E and CP1H may be not support interrupt INT. How can we program it? Thanks & best regards, -
Dear Mr, Thanks for your helps. I will check software again. Best regards, -
Dear Mr, Thanks for your helps. I will check software again. Best regards, -
Dear Mr Sparky, Thanks For your helps. So that mean PLC pulse input will not be affect by duty of program from ladder 0 to ladder n, is it. Best regards, -
Dear Mr/Ms, Please tell me how to setup without GX developer install. Because I just install GXworks2 and GT designer 3. Thanks & best regards, -
Dear Mr/Ms Sparky, If I want to use Omron CP1H without any high speed counter module, just only using high speed input that have compact on CP1H for high speed pulse. For example, Input 00.00 recognize pulse not less than 0.2us, with input from instrument with pulse 0.1ms this mean in normal condition 0.00 can read that pulse. But if we have program with 9000 network , then PLC will read program from network 0 to 9000 need 10ms. So I don't now PLC can read pulse 0.1ms or not? Please help me to solve this problem. Thanks & best regards, -
Dear Ms Expert, Thanks for your help. This document really help me to solve that problem. Best regards, -
Dear Mr/Ms, If we use Omron CP1E with 0.00; 0.01;0.02 for high speed. Example 0.00 is 0.02ms/pulse and with heavy program need 1.2ms/duty so that 0.00 can read input with pulse 0.03ms or not? Please help me to slove this. Thanks & best regards, -
Dear Mr/Ms, If we have 2 Omron HMI NB10 series and if have to connect and program with Mitsubishi Q/FX PLC. How can we connect them? and Program for PLC . HIM can understand which Program language in PLC mitshubishi? Everybody, Please help me!! Thanks & best regards,
How to simmulate GT designer 3 by using GX works2
in Mitsubishi
Posted