Error downloading to PanelView 1000

[Guest technogumbo]

I am needing to modify the operator interface program on an Allen-Bradley PanelView 1000 that talks DH+ to a PLC-5/25. The operators need some additional features. I can easily upload the program out of the PanelView through out DH+ network. However, when I go to download the modified program, PanelBuilder32 stalls and gives an "Error 1030 - No commands received from operator terminal" fault. I tried uploading the existing program and then re-downloading the same program, but have the same fault error come back. I remember with the older PanelView 1200's that you had to turn a key switch to enable the download and upload. I could find no tech notes or knowledgebase articles on AB's website to point me in the right direction.

[Guest HalBishop]

There is no keyswitch on the PV1000. This is from the Rockwell Knowledgebase: Problem: Error 1030 - No Commands Received From Operator Terminal Explanation: This error can occur during a DH+ to DF1 passthru (PC - DH+ - SLC 5/04 - DF1 - PV) if the PV is not set to the default node of 1. Since PV is point-to-point only, it serves no purpose to ever change the default DF1 node on the PV. However, the software will ALLOW this change if 'USE NETWORKING' is checked in the communications settings in PB32. Unfortunately, once you change the node to something other than 1, passthru downloads cease working. Often times, the upload functionality will still be working, making it seem like everything is ok. Resolution: Change the node number on the PV to node 1 (and then remove the check from the 'USE NETWORKING' checkbox). The passthru download should then complete normally. and: The customer was running a software package from Trend Micro called PC Cillin which prevented PanelBuilder32 from dowloading to the DH485 Panelview terminal via the SLC5/05 Ethernet controller. The firewall protection software must be disable from within PC Cillin before the download can proceed. Ensure the following bits are set correctly on the SLC5/05 - Status File, Chan 1 tab: DH485 Gateway Disable Bit S:34/0 = 0 DF1 Gateway Enable Bit S:34/5 = 0 and: This tech note attempts to qualify all passthru download combinations for PanelBuilder ND3 and END1. See also the passthru tables in the PB32 online help under contents, transferring applications, for the latest combinations. IMPORTANT: Passthru has occasionally been seen to crash/fault and/or clear memory on some processors (5/40,5/60,5/80) during the passthru operation. Make sure the PLC has not maxed out resources or block transfers. Make sure that the block transfer queue in the PLC is not full and that any BTs are not erring out. Keep all block transfers in the PLC as non-continuous if possible to minimize resource timeouts. Passthru only during non-peak times. With the PV1200/1000e/1200e/1400e, use the Inhibit, Request and Status bits in the PanelView to regulate the passthru operation for downloading; they do not apply to uploading. (the Standard PV's do not have these control bits). Upload/Download Summary: ND3 2.60 w/ RSlinx 2.0 and PB32 3.61 w/ RSLinx 2.20.02 (now PB32 3.70 as of June 2001): Remember to "configure client application" for the driver in RSlinx with PB 2.60! SLC 5/04 DF1 channel 0 to RIO YES DH+ channel 1 to RIO YES DF1 channel 0 to DH+ NO (YES if PB32 and PV f/w 3.30 and RSLinx DF1 set to KE/KF2 and bits S34/0 and 5 set to 1) DH+ channel 1 to chan 0 YES DH485 or DF1 Anything to 1747SDN NO SLC 5/03 DF1 channel 0 to RIO YES, ND3 2.60 Jan 99 will support this. Requires 5/03 OS302. DH485 channel 1 to RIO YES DF1 channel 0 to DH485 NO DH485 chan 1 to chan 0 NO SLC does not support Chan 1 to Chan 0 bridging DF1 1747KE to DH485 YES DF1 1770KF3 to DH485 YES Anything to 1747SDN NO PLC5 DF1 channel 0 to RIO YES, internal DF1 failed with "cannot guarantee delivery, link layer timed out or rec'd a NAK". DF1 channel 0 to DH+ NO, not supported by PLC DH+ to RIO YES PLC5C DF1 to Cnet NO DF1 to RIO YES Cnet to RIO YES Cnet to DH+ NO PLC5E DF1 to Enet NO DF1 to RIO YES Enet to RIO YES PB32 Enet to DH+ NO Anything to 1771SDN NO Direct DF1 1785KE to DH+ YES DF1 1770KF2 to DH+ YES DF1 1747KE to DH485 YES DF1 1770KF3 to DH485 YES PIC to DH485 YES PCMK DH485 to PV YES KTX DH485 to AIC to PV YES 1785KA5 DH485 to DH+ YES KT/KTX to DH+ direct YES KT/KTX DH+ to 1785KA5 to DH485 YES, PB 2.60; NO PB32 upload, but not download, error 1030 DH+ to KA to DH to KA to DH+ YES PCMK DH+ to 5/04 to chan 0 YES PCC to Cnet YES PB32 KFC to Cnet NO KFC does not support Cnet 1.5 KTCX15 to Cnet YES PCD/KFD to Dnet YES PB32 DF1 to SLC CH0 to SDN NO Enet direct to PLC/SLC YES PB32 ANY RSlinx Gateway NO (cannot download via RSlinx gateway, but upload works) May get "Error [1030] : No commands received from operator terminal" when downloading. This includes ETH to DH+ or DH+ to DH+ SLC 5/05 DF1 channel 0 to RIO YES Ethernet channel 1 to RIO NO (YES w/ PB32) DF1 channel 0 to Ethernet ? Ethernet chan 1 to chan 0 NO (YES w/ PB32) Anything to 1747SDN NO ControlLogix DF1 to Anything: YES to CNB, ENET and DNB ENET or CNB to DNET: YES, except DNB to DNB ENET to CNET: YES, except CNB to CNB CNB or ENET to DH+: YES, download requires PB32 3.61, RSlinx 2.20.01 (SP1), ENET/A 1.18, DHRIO 2.17, DH+ PV 4.10 f/w. See KB 12810. Must also populate all link ID's. RSLinx 2.20.01 added support for configuring the DHRIO routing table and assigning link id's. This was needed to support the unsolicited reads from the PV terminal. Anything to RIO: YES, except DF1 Anything to DF1: NO, L1/L2 does not support serial port passthru CNB to ENET ? ENET to ENET ? END1 4.0, RSLinx 2.0 or END1 5.13, RSLinx 2.1: Now at END1 5.15, RSLinx 2.20.02 as of 2001. Note: on channel 0 downloads, RSlinx DF1 must be set to KF2, NOT SLC or PLC CH0 Do not do a superwho with the DF1 set to KF2 when connected to Channel 0 of a PLC/SLC, it will show multiple duplicate devices on the who. Just do the download, then change it back to PLC CH0 for the programming software. NOTE: DF1 is using Serial driver in PBe, not RSlinx DF1 driver. Must remove the DF1 driver in RSlinx to prevent a conflict. To use DF1 driver in RSlinx, it must be setup as a KF2, then in PBe, use 'network' and 'AB_DF1' selection. SLC 5/04 DH+ to RIO YES DF1 channel 0 to RIO NO DF1 channel 0 to DH+ NO ; Error 4209 Host PC failed to communicate with the PanelView Terminal RDM 0x5 SLC 5/03, OS302 DF1 channel 0 to RIO NO PLC5 DF1 channel 0 to RIO YES, internal DF1 also worked DF1 channel 0 to DH+ NO, not supported by PLC DH+ to RIO YES PLC5C DF1 to Cnet NO DF1 to RIO YES Cnet to RIO YES Cnet to DH+ NO PLC5E DF1 to Enet NO not applicable DF1 to RIO YES Enet to RIO YES Enet to DH+ NO Direct DF1 1785KE to DH+ YES KT/KTX DH+ direct YES DF1 1770KF2 to DH+ YES DH+ to KA to DH to KA to DH+ YES PCMK to DH+ YES PCC to Cnet YES SLC 5/05 DF1 channel 0 to RIO YES Ethernet channel 1 to RIO NO DF1 channel 0 to Ethernet NO PLC 5/250 or Pyramid Integrator DH+ to DH+ YES (with PI link ID) (pub 2711E-6.16, pg A-3) DH+ to RIO ? Enet to DH+ NO Enet to RIO NO ControlLogix DF1 to Anything: NO Anything to CNET: YES, Transfer Manual shows DH+ to CNET, page 2-11. Anything to DH+: NO The PVe xfer utility does not support the DHRIO routing. This includes ENET to DH+, CNET to DH+ or DH+ to DH+. Anything to RIO: YES, except DH+ or ENET to RIO NOTE: The PVe does not support runtime routing via the DHRIO module to other DH+ networks. See the PB1400e Transfer Utility Manual, 2711E-6.16, for various downloading examples. Download from www.ab.com/manuals under EOI. **************************************** MODEM DOWNLOAD ISSUES Most any download using the RSLinx DF1 driver can use modems. There is no need to attempt this with Interchange, we can now use RSlinx for both ND3 and END1 software. There is information on this error on the Rockwell Automation website. I found these and did not have to login to my account. It seem s that you may be losing communications to your panelview during the down load. Make sure there is no too much traffic on you DH+. You can always upload and download using the serial port on the panelview. This is the easiest way to ensure that the application is downloaded. Just hook up your serial cable, configure your driver and you are golden. Good luck.