Mr7
MrPLC Member-
Content count
37 -
Joined
-
Last visited
-
Arun kumar started following Mr7
-
I have stepper motor with modle hb b3c i want to drive this on position mode i have not its manual kidly any body help he I need on its manual
-
mitsubishi A700 inverter revers rotation after dc injection brake reales
Mr7 posted a topic in Mitsubishi
dears i have a problem on mitsubishi A700 intervert i am using dc injection brake for inverter brake.the dc injection brake working properly but when the brake realse motor move littel bit reverse.how can i control this revers movment.and one thing i am using run stop from pu.other thing there is no machnical load on motor -
thanks the5150 my problem is solved the pr384 was disabled thanks
-
Dears i have a problem. My application drive A700 inverter on position mode (with pulse train) plc is mitsubishi fx14mt softwear is gx develpor. I read the applied manual there is parameter 291 for selection of pulse train .i changed it from 0 to 1 but its not working kindle give me the parameters of inverter and one thing i am not using A7AP card with inverter.i am want to drive dritct with plc pulses. For input the pulses i am using jog terminal of inverter. These pulses given by plc and the sd terminal is connected on com terminal of plc. And stf terminal for direction. I program the plc with plsy instraction properly.kindly give ne sime adivse its urgent
-
I think you open maximum gx developer application.first u close all gx application or restart your system
-
Guys i have prblem.i have AOJ2 cpu,i want to cmunicate with 1030 GOT.i need cable layout can any body give me pin configration for communication between them.
-
Mr Inntele is right i am not discuse about hacking or cracking .but my problem is solved.i was not able to clear its memory but when i download a simple program and after that.i was able to clear its memory
-
Yes i know .but when i try to clear the memory the password msg is appear.
-
Hello dears i forget the password of fx3u plc.i have the program copy.now i want to modify the program and then download it in plc but the plc demonad the password .now i want to clear its memory how can i do this.
-
Can any body help me,I want to watch weintek HMI status on my PC the plc is Mitsubishi fx3u ,HMI wentek 3120 ,But the main thing is I am not using PC direct with plc .my requirement is watch the HMI status on pc.
-
Dear there is no detail about co2r4 i need to know only pin configuration of c02r4 female 9 pin side.
-
hy dears this is urgent i have a problem i want to communicate gt1672 with qj71c24n with co2r4 cable but the size of cable is very short i want to extend is kindly tell me the detail pin configuration female 9 pin connector of co2r4 cable.i already check the connection are given in got 1000 connection manual chapter 7.3.2 but i think there is not proper information available. kindle give me some information about it.thanks
-
Thanks bro but i need maximum 2 ms scan time no i replace 4DA with 2 bd cards and ADPT with seprat controller now the time scan is bcame 1ms actually there is 2 anslog outs requier thank again gor good information
-
Yes u right kaare-t i have one 4DA and one 4ADPT modual on right side of plc ok thank for reply i try to replce 4adpt with seprat controller may b then the problem solve.
-
Hy every one i have problem in scan time i oprate 3 servo motors in position mode ,the plc is fx3g software gx develpore,during opration the scan time increase at 30 ms ,is there any posibility to reduce time scan.in th program i use 1 to 40 ms 4 timers ,so when scan time is increase the program not work properly