structerd tekst Structured tekst

[A.J 0]

Hello fellow members,

 

It’s Beaning a wail that I have post on this form. But i need some help.

 

I have experience with programming plc in ladder and function blokes.

 

 

 

But not whit structured tekst.

 

I have made a recipe so that the machine can switched easy to divert parameters.  

 

 

 

No I have problem whit the ‘default settings’ for some parameters that van be de basic when something goes wrong.

 

 

 

Can anyone tell me wot I do wrong I have sent son screenshot to help you understand what I mean.

 

 

 

Thank you in advance

 

Device varible to device is not a problem

Not varible to device is a problem

 

For example what i mean whene I make it in ladder. 

Edited 12 May 2023 by A.J
more informatie

[Gambit 324]

Haven't checked the code but there is a space before the 10. Could be the issue.

which PLC are you using and which software ?

Hmm checked with GX 2 but it compiles without any problem 

 

Edited 15 May 2023 by Gambit

[A.J 0]

Hello Gambit, 

 

Sorry for a very late reactie, I have binne pretty busy.

 

But a use a fx5U plc and GX works 3.

 

I have use a space betore 10. 

 

If i got time tomorrow i willl check to be sure. 

[FRANK RUIZ 2]

hi Gambit, on the back of this, I am using ST on FX5 to do some maths with floats, in your opinion, does Mitsi have anything to help me separate the result into 2 groups. 1 where digits on left of coma are stored, 2 right to coma.

 

so for example, after a calculation I get a float of 2.34, how can I separate 2 from 0.34. The PLC needs to see that has to multiply 2 by 7, then 0.34 by 128.

 

Cheers.

[Gambit 324]

1 hour ago, FRANK RUIZ said:

hi Gambit, on the back of this, I am using ST on FX5 to do some maths with floats, in your opinion, does Mitsi have anything to help me separate the result into 2 groups. 1 where digits on left of coma are stored, 2 right to coma.

 

so for example, after a calculation I get a float of 2.34, how can I separate 2 from 0.34. The PLC needs to see that has to multiply 2 by 7, then 0.34 by 128.

 

Cheers.

DEBCD(P) will seperate the exponent and the mantissa part.

But if you convert the Real number (2.34) to an integer value (FLT2INT) you will get an integer value (2).
turn that back into a float INT2FLT and subtact that from the origional with DESUB(P).
you should have your remainder (0.34)

 

 

 

[FRANK RUIZ 2]

4 hours ago, Gambit said:

DEBCD(P) will seperate the exponent and the mantissa part.

But if you convert the Real number (2.34) to an integer value (FLT2INT) you will get an integer value (2).
turn that back into a float INT2FLT and subtact that from the origional with DESUB(P).
you should have your remainder (0.34)

 

 

 

thanks a million!

[A.J 0]

On 15-5-2023 at 10:05 AM, Gambit said:

Haven't checked the code but there is a space before the 10. Could be the issue.

which PLC are you using and which software ?

Hmm checked with GX 2 but it compiles without any problem 

 

Hello Gambit, 

 

I Have done somthing wrong begos me reply dit get on the form.

So i trie a gain. 

 

I use a FX5U,  and GXWorks 3

I have ols seen that I have space bewteen de the 10 and i have space.

 

I tried it wit a different device  that works, verry odd I think

[Gambit 324]

Which Dev did you have before and into which device did you change it ?

[A.J 0]

I don't change a Dev but I add a Dev. 

I add Dev D200 to test i that works, and that works. 

 

thats wy I think its odd that it doessent works white the label name

[A.J 0]

The problem was dat I not use the recept nummber in watch dog. But i use the basis. 

Thit use 

Recepten[Recept.Pointer].aantal_pot_in_laag

most use;

Recepten[17].aantal_pot_in_laag

 

Thank you Gambit