Posted 15 Dec 2016 Hello, I have AB PV 300 micro HMI and AB ML 1000 PLC . i want to configure it so how i can do it ? is it possible to configure both without AIC ? Which cable is required please help me. Thanks in advance Share this post Link to post Share on other sites
Posted 15 Dec 2016 (edited) See pdf page 14 for the proper cables. You do not need an "AIC" to get connected as long as this is just point to point (PLC to HMI) and not networked. The PV300 Micro comes in two different favors "DF1" and "DH485" protocol, your PLC will have to be configured for the supported protocol. If you can post the complete catalog number of your HMI someone can help with that if needed. PV300Micro.pdf Edited 15 Dec 2016 by Mickey Share this post Link to post Share on other sites
Posted 16 Dec 2016 Thanks sir , I have PV 300 Micro (2711-M3A19L1) Series A . I have AB ML 1100 PLC and HM 02 Cable also . I do not have AIC so how i can configure all this in network please if possible send with me all necessary steps. I tries to connect it with HMO2 and Ethernet cable with 1100 but while downloading program from PC to HMI i am getting some errors which are attached in Images please have a look into this and help me. Share this post Link to post Share on other sites
Posted 16 Dec 2016 This is a new PanelBuilder 32 application, correct? Post screenshots of your communication setup. You are using an Allen-Bradley #1761-CBL-HM02 cable => DH-485. Refer to page 56. Typically, PLC = Node 1 and HMI = Node 2. http://literature.rockwellautomation.com/idc/groups/literature/documents/qs/2711-qs003_-en-p.pdf 1 person likes this Share this post Link to post Share on other sites
Posted 16 Dec 2016 (edited) Thanks but still I did not get it . what are the cable are required and how they need to be connected cab you please explain me with diagram so I will be able to do it and in panelbuilder while downloading program to HMI what configuration needs to be selected please help me. Is it possible to connect PC , HMI and PLC in network without using of AIC? Edited 16 Dec 2016 by ankitjd Share this post Link to post Share on other sites
Posted 16 Dec 2016 You want help designing your system? Start with getting the PanelView 300 user manual to identify what ports are available. You have not specified the part numbers of the devices you are working with. http://literature.rockwellautomation.com/idc/groups/literature/documents/um/2711-um014_-en-p.pdf The MicroLogix 1100 has ports: Ethernet RJ-45 and RS-232/485 round DIN. http://literature.rockwellautomation.com/idc/groups/literature/documents/in/1763-in001_-en-p.pdf Please post your specific PLC and HMI part numbers. Share this post Link to post Share on other sites
Posted 16 Dec 2016 I have PV 300 Micro (2711-M3A19L1) Series A . I have AB ML 1100 PLC and HM 02 Cable also. Now I want to connect PLC , hmi and PC together . suppose I just want to make one start stop logic with PLC and HMI so what would be the connection between all these please help me how to transfer HMI programming from PC to HMI and how to communicate HMI and PLC together Share this post Link to post Share on other sites
Posted 16 Dec 2016 (edited) Your HMI (PV300 Micro) supports DH485 protocol. The cable you have 1761-CBL-HM02 is the proper cable if connecting your ML1100's serial port directly to the HMI. You will need to configure the ML1100' serial port for DH485 protocol. The baud rates on your ML1100 and the HMI need to be the same also node addresses need to be different. Your HMI 's baud rate defaults to 9600 ,the ML1100 defaults to 19.2 change one of them so they match. To get connected from your PC to the Panelview you are going to need a 1747-UIC ( USB to DH485 converter) See link if you don't have one Another option is to change the protocol on the PV to DF1 this would make it easier (cheapter) to get connected from your PC to the HMI. It's a firmware change, it should be on the PanelView32 'CD or contact your local AB repr. Does you PC have a real serial port? http://www.plccable.com/allen-bradley/ See link for PanelView 32 manual https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0ahUKEwiw2pzWl_nQAhWLxFQKHS8FBYoQFggaMAA&url=http%3A%2F%2Fliterature.rockwellautomation.com%2Fidc%2Fgroups%2Fliterature%2Fdocuments%2Fgr%2F2711-gr003_-en-p.pdf&usg=AFQjCNFHJYroYm5PbVWX834Gms0Q66E5tg&sig2=jNRgRRoKQ-TPG6SrVY3PCQ And some tutorial sites... https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=panelbuilder32+tutorial Edited 16 Dec 2016 by Mickey 1 person likes this Share this post Link to post Share on other sites
