How to Add Rack in PLC Omron CP1h

[iqrom 0]

Dear All,

Hi, Im newbie here, please help me to out from my problem. I wanna ask about  "how to add rack in PLC Omron CP1H??" and "How see address Built in AD/DA on Settiing?"

 

Thanks All

 

[Jay Anthony 118]

[iqrom 0]

can I get your manual book ? So, Maximum slot in Main Rack CP1H just two?

I have Five  AD041 and One DA041, In Software  Just Two "Empty Slot", Can I add Empty Slot again? and How?

 

Thanks Jay

 

[Jay Anthony 118]

Quote

So, Maximum slot in Main Rack CP1H just two?

Only two CJ1 modules can be used on Main Rack.

[gtsuport 61]

With that amount of analog, it would be better to use a CJ2M processor.

Main rack would be able to support 10 modules. 
Up to 3 expansion racks with 10 modules each could be added.

CP1H can be programmed with the Lite version of CX-One.  CJ2 would need the full version of CX-One.

Hope this is helpful.

[pfort 20]

What are your (complete) number of expansion modules? Does they begin with CP1W ?

And, complete number of the PLC?

Edited 17 May 2016 by pfort

[iqrom 0]

11 hours ago, pfort said:

What are your (complete) number of expansion modules? Does they begin with CP1W ?

And, complete number of the PLC?

I dont understand complete number of expansion and start with CP1W, How to Configured All of Them. Pliss your tutorial about that

 

Thanks

[pfort 20]

You don't have to use "IO Table and Unit Setup" for CP1W expansion. This is only if you want to add CJ1 modules (2 max).

Section 5 (page 325) for your built-in analog IO, and section 7 (page 389) for expansion units.

[iqrom 0]

15 hours ago, pfort said:

So, In Software I dont have to edit "io table and unit setup"  to input My Expansion Analog Input? h

I just play with CIO Word Address like that Capture?

 

Edited 18 May 2016 by iqrom

[pfort 20]

Yes, and further in section 7, you will see that you have to write a "range code" in the ladder.

[iqrom 0]

OK THANKS ALL FOR YOUR SOLUTION   I GOT IT

[pfort 20]

On 5/17/2016 at 9:37 AM, gtsuport said:

With that amount of analog, it would be better to use a CJ2M processor.

Main rack would be able to support 10 modules. 
Up to 3 expansion racks with 10 modules each could be added.

CP1H can be programmed with the Lite version of CX-One.  CJ2 would need the full version of CX-One.

Hope this is helpful.

I did not pay attention enough before to your quantity of AD041 (5) and gtsupport was right of course.

You can not have more than 3 of them because you are limited to 15 inputs words, and they need 4 input words each.

[Suru 0]

how can i jump the connecting line over another in cx one program....

[Crossbow 295]

On 8/13/2016 at 7:22 AM, Suru said:

how can i jump the connecting line over another in cx one program....

What are you talking about?

[Michael Walsh 268]

Do you mean like this?  Like in an electrical schematic?

 

If so, you cannot do that in ladder logic.

[Suru 0]

yes i mean that ...... thaks for the replay

[Suru 0]

my omron plc is of npn type that means common -ve .. if accidently connect another -ve terminal which is anoutput from a sensor (-24v). if there is any problam for that.....

 

[Crossbow 295]

You need to make sure the common terminals are wired to the same power supply as the devices wired to them.

[marcinmrag 1]

Hello Experts!

I have a question. I have one module MAD42. Im going to add one more extra connected to the first one. How to set the input configuration for second module? I can't figure out exactly
how to set configuration for second Analog card. For the second card i should move for example #80ED to 104 and 105? Than read the input from 6 to 10?

 

[gtsuport 61]

We need to understand your configuration.

Do you have two CP1W-MAD42 modules?

Or are they CJ1W-MAD42?

Thanks,

gtsuport

[marcinmrag 1]

1 hour ago, gtsuport said:

We need to understand your configuration.

Do you have two CP1W-MAD42 modules?

Or are they CJ1W-MAD42?

Thanks,

gtsuport

CP1W-MAD42 . I have one but I going to connect another one. I need more than 4 analog inputs. 8 Inputs should be enough.

[gtsuport 61]

Yes, your original post is correct.

Thanks,

gtsuport