Sign in to follow this  
Followers 0
JLDrescher

SLC5/03 w/NET-AIC+ DH485 Comm Problem[s]

4 posts in this topic

RSLogix500 & RSLinx DH485 w/NET-AIC+ Communications Network Setup Attachments Incl; 1] SLC_NET_AIC+.jpg [Network Layout] 2] 100-1069.jpg [EEP Panel] 3] 1761-CBL-AS03.pdf 4] NETAic.RSS 5] AB_PIC-1.jpg [RSLinx AB_PIC-1 Driver Setup] Trying To Establish a DH485 Comm w/ SLC-5/03, CH-1 [RJ45] w/1761-NET-AIC+, After Several Attempt's, and Correcting The Homebrew 1761-CBL-AS03 [sIG GND was connected to CHS GND] Cable. Note: 1747-PIC Works Fine On Com-1&Com-2 w/ SLC5-03 CH-1 [RJ45] Reviwed Every Document @ Forum Relating To SLC5/03 DH485, Helped Me Verify Miswired Homebrew 1761-CBL-AS03 Cable, Went to UTube Link Referencing "DH485 Communications Network Configuration" referencing a Micrologix-1200 {http://www.youtube.com/watch?v=nKaGmXdXygo}, Excellent Detail's, Did Not Get SLC5-03 Running, Still Not Listed In RSLinx Lite Using AB_PIC-1 Driver [1747-PIC/NET+ Driver]. Originally Established Network Comm w/AB_DF1 Using The NET-AIC+, Then Attempted w/AB_PIC-1, No Luck/Skill, Strangely, Could Not Re-aquire SLC5-03 On CH-0 w/AB_DF1 Even Going Point to Point w/1747-CP3, Discovered During Attempt, S:2/15 Went True, Preventing Comm On More Than 1 Port, Now I Have Edited a S:2/15 [Comms Servicing Selection]Unlatch & SVC Logic To NETAic.rss I Know That I'am Missing The Proper Sequence For Deleting The AB_DF1 & Creating The AB_PIC-1 Driver Along w/RSLogix-500 Configuration, But Not Sure Yet What They Are. This Is The Same House Project I Started Last Year and Received Help From You All, Finally Got Hoffman Panel Builted Up/Installed And Internally Wired. Any Direction/Comments Would Help, Thanks, Jeffrey Drescher NETAIC.RSS 1761_CBL_AS03___1761_CBL_AS09_Cable_Pin_Out.pdf

Share this post


Link to post
Share on other sites
I think you use the wrong driver in RSLink. If you are connected to DB9 of AIC+, you may try DF1 see screen shot.
1 person likes this

Share this post


Link to post
Share on other sites
Tried It, I Disconnected SLC5/03, CH-1, 1761-CBL-AS03 Cable, Connected 1761-CBL-PM02 Cable From NET-AIC+ [8-Din] To SLC5/03, CH-0. Then Deleted AB_PIC-1 Driver / RSLinx, Added AB_DF1, Auto Configured-Successful. Chg Offline NETAic.rss [RSLogix-500]/ Tools/System Options, Selected New Driver, AB_DF1, Download To PLC, AB_DF1 Communications Re-established @ 19200, COM-1, SLC5/03 In Run Mode. Disconnected SLC5-03,CH-0 [1761-CBL-PM02] Cable, RSLinx, Comm Error 00000005 Connected Cable 1761-CBL-AS03 From NET-AIC+ [Phoneix] To SLC5/03, CH-1 [RJ45], No Comm/RSLinx, Red-X Node-1 [AB_DF1] Removed 1761-CBL-AS03 From CH-1, Connected 1761-CBL-PM02 To CH-0, Have Comm/RSlinx, Node-1.

Share this post


Link to post
Share on other sites
TRYING THE SAME HERE, DID YOU SUCCEDED??? IF SO, I GOT SOME QUESTION ABOUT THE CONNECTIONS, I WOULD LIKE TO CONTACT YOU BY EMAIL. CONGRATS. Ing. Luis Enrique Jimenez Calvo

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0