Search the Community

Showing results for tags 'xbt-a72101 eeprom file'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 37 results

  1. I am trying to use Reusable files, but it is greyed out. Is there a setting that needs to be enabled to activate it? I am using CX-Programmer v 9.74 Update 1: Apparently, when you create a data structure this gets greyed out  
  2. I have a 1747-L30B SLC Brick and it is set to load from EEPROM on boot S:5/8, Error S:1/10, and Run S:1/12. I need to make changes to the program and then store it to EEPROM via "Comms>EEPROM>Store to EEPROM."  When I attempt to store the program with changes, it displays the message "Insufficient Memory Module Size." I assumed the EEPROM memory was maxed out, but I also uploaded the existing program currently stored to EEPROM, made no changes, and attempted storing it back to EEPROM and received the same message. Any advice?
  3. GX Developer project does not open

    Hello All, I have a GX Developer project folder file sent by the client. I am not able to open. It opens the GX Developer and says Failed to read the project file. The screen shot is attached. Also the  the project is attached. Please help me to open the project. I am using GX Developer version 8.91V 显示器 综合测试.rar
  4. Hello everyone, I am working on a plc upgrade and the client provided the old code file which has the extension .gps. Can anyone tell me what type of code file this is? And second, is there anyone I could hire to open this file and create a pdf version of it for me? Thanks. Gppw.gps
  5. Codesys 2.3

    Cpu 2211 ple send 
  6. I have a huge confusion regarding the retentive timers on FX3GE. According to the programming manual for FX3G(image attached), all retentive timers use the EEPROM. This is very confusing to me because the retentive timers are modifying the measured time constantly in an EEPROM register and EEPROM type of memory is known to be write limited. After a couple of million write cycles the EEPROM registers burnout. I've experienced this myself by constantly using the T250 and after a while it became unusable. The timer stopped counting time after some time. This leads to my decision that retentive timers on FX3GE PLCs are something that should бе used only on rare occasions so as to avoid EEPROM memory burnout. If this is true than the real question comes in: What is an alternative for using retentive timers on FX3GE when you want to measure time between two events. The instruction TTMR for teaching timer is appropriate however this instruction does not exist on FX3G series.  
  7. Hello, hardaware: NX1P29024DT1 (ver1.18), frequency inverter Altivar ATV320U07M2B (ver. 2.7 IE32) and communication EtherCAT card VW3A3601 I have a few ESI files v.109, 111, 113, 114 instaled in Sysmac Studio in ESI Library. I can not establish connection between NX1P2 and ATV320 by EtherCAT. In Network cofiguration I add slave with Node Address 2. The same Address is in ATV320 (ECAA and ECSA - parameters). When I connect both I see "Network Cofiguration Verification Error" Code 84220000 and black cross on diagram "Not matched" in Sysmac Studio. On the communication EtherCAT card in Altivar LED1 Green Filickering (Link, activity) but LED2 is OFF (EtherCAT state: INIT). I see in Altivar that parameter ECSS (EtherCAT slave status) INIT. If any one have experience with connection by EtherCAT NX/NJ with ATV32, 320, 340 ? p.s. The same communication EtherCAT card VW3A3601 I use for communication the same NX1P2 with serwo Lexium32M, of course with the appropriate ESI file for this slave and comunication is OK.
  8. Hi, I have inserted new RTD module into in my SLC500 as replacement to defected RTD module however the module LED is enabled but the channel LED's are blinking. I have checked the following: In the advanced I/O configuration the module configuration is shown as expected In the data file word format it is not corresponding to the channel preferences What should I do and how to fix the word bits?        
  9. Hello Im trying to read from my PLC but i cannot see the program file.  However, if i try to compare it using other file program, i could see the program file. Is their any restriction in my software?
  10. Hello, I have some files for a piece of equipment but do not have the RSlogix software to view the code. It is for a SLC 5/02 plc. Would anyone be willing to convert the files to pdf for me, it would be greatly appreciated. Thanks in advance! 2730-AR14.RSS 2730-AR10_BAK494.RSS 2730-AR10.RSS 2730-AR9.RSS 2730-AR7.RSS 2730-AR15.RSS
  11. Folks, we have a set of Mitsubishi Q12PRHCPU (redundant) running effortless since many years. CPU-A as standby and CPU-B as Control. Recently we noticed BATT low alarm on CPU-B. So we arranged for a spare battery Q6BAT and started the procedure as per manual(attached procedure and flow chart). We did memory copy from Control to standby (as prescribed precaution) and did the Reset of Standby PLC CPU-A. Memory copy from B to A completed successfully 100%. But the BACKUP LED did not turn Green from Red & Error LED kept flickering on standby CPU-A. CPU-B remain in Control but backup LED turned RED. From system monitoring we found that there is a Error 6000 (FILE DIFF.) observed in One of the .QPG (program 00-MDBUS.QPG). We tried to reset it but were not successful. We are surprised that why does the program differs when it was copied from CPU-B to CPU-A using the memory copy. Still we did the VERIFY and found no difference between the programs in CPU-A & CPU-B.  Can anyone explain the cause of this issue and the solution. Please note that the CPU-B is still in control and plant is running. Backup LED on both CPU are red which means (redundancy loss) and error LED on standby CPU-A is flickering RED. There is no error in the CPU-A (Control) -we checked this using the GX Developer. Also attached here are the image of the error and error help. Thanks in advance. Battery Replacement procedure.pdf Battery Replacement procedure-Flow Chart.pdf Error.pdf MELSEC QCPU ERROR CODE 6000 FILE DIFF.pdf
  12. Sorry if this is covered elsewhere, but my search hasn't revealed anything yet.  I have a number of PanelView graphics created with FactoryTalk View ME and some use a lot of Parameter Files, which link to popup faceplates. So a large number tags are represented with parameter files, which, when clicked on screen, then pop-up an appropriate faceplate, based on tag type or category etc.  I am still digging into the very elaborate FT View ME manual, but at 500 pages, that's quite a deep study.  But I don't see the linkage between the tag's parameter file and how it specifies which faceplate to pop up, and I've not yet found a good article other than keep digging into that FT manual. There does not appear to be a linkage entry in the parameter file itself, where I would have expected it.  Nor do I see any "hot spot" click type event code in the display itself, which would also make sense.  Is it in the PLC code itself?  I would not have expected that, since they seem to be keeping the FT environment self-contained. But there must be some sort of table or linkage somewhere that I'm over looking. Thanks in advance for anyone's thoughts & guidance on this.  Other parts of FT HMI screen development does seem intuitive, just not this dynamic linking.
  13. Hi all, I'm enhancing an Ethernet IP driver but only just learning the ropes in terms of Allen-Bradley PLCs. I'm presently focussing on that part of the driver which specifically supports SLC/500 & MicroLogix 1400, for which I have one controller of each type for testing purposes. I can already cater for a range of standard file types: integer, float, binary, input, output, string, counter, timer, control, status, and this is working well. However, by working with RSLogix500, I can see that there are other data file types which can be hosted in these controller types (dependent on model) and, indeed for test purposes, I have actually created instances of them as follows: ASCII (at A21, 20 elements) for both SLC & ML1400 Long (at L22, 10 elements) for ML1400 Message (at MG23, 8 elements) for ML1400 PID (at PD24, 4 elements) for ML1400 Programmable Limit Switch (at PLS25, 3 elements) for ML1400 Routing Info (at RI26, 3 elements) for ML1400 Extended Routing Info (at RIX27, 3 elements) for ML1400 Now, the driver obviously uses standard DF1 PCCC data types (see below) to read/write individual elements/sub-elements of the file types that I can already support -- and I can see that there's a file type listed below for ASCII. •80 to 83 hex: reserved •84 hex: status •85 hex: bit •86 hex: timer •87 hex: counter •88 hex: control •89 hex: integer •8A hex: floating point •8B hex: output logical by slot •8C hex: input logical by slot •8D hex: string •8E hex: ASCII •8F hex: BCD However, my question is this: since there are no hex file types corresponding to non-elementary data types such as L, MG, PID, PLS, RI and RIX, what file type do I specify in my DF1 PCCC packets to read/write the elements/sub-elements of these six data types ? Thanks in advance.
  14. In my research on NJ processors and 1S servo programming, I came across an HMI graphic that I would like to use.  There was a file download that I think had something to do with it..."Machine.IAG"..but I don't know what an IAG file is and if it even has anything to do with an NA5 display.  Is it a Graphics file I can load into my HMI program to use?   Thanks,
  15. I thought only PLC5's had EEPROM, but I was told MicroLogix PLC's also have an EEPROM that need to be burned to... What are all the PLC's that have EEPROM and require an EEPROM burn to prevent the program from being wiped in a power cycle?
  16. mitsubishi PLC R series

    I have R16 PLC (firmware45) and SD card(2GB). Can any one help me to create CSV file in SD card.I need to Logg the data of D0-100 when the M0 trigger bit goes high. can any please help to creat  ladder for this. it will be really helpful.
  17. How I open file bin ihm fuji UG 530h ?

    I need help, I want modification ihm fuji UG 530h , the upload file bin, I am use software VSF edit V6.0, but not open.
  18. Omron CSV FILE

    Hi Everyone.I want to read the csv file to plc. How can I do it. I will use to NB 5Q-TW001B for hmi.  PLC model : Omron CP1L-E
  19. simotion MMC img file

    Hello I have a SIMOTION MEMORY CARD 16MB for C230-2. Order No: 6AU1700-0AA01-0AA0 That formatted with windows. I need image file from Simotion MMC 16MB for write to This MMC with s7 img writer. Someone can help me. Thanks.  s7imgrd2.zip s7imgwr2.zip
  20. FX2N - 48MR (MELSEC)

    Hi everyone! I buy a new Mitsubishi FX2N - 48MR PLC. I just want to asked If I can directly removed the EEPROM from the old PLC and transfer it to the new one without losing the data?
  21. I'm attempting to make a backup of a program, complete with comments. I go connect to the PLC over Ethernet, and select Use Upload File to merge the comments from an original copy of the program. After that, I go file-saveas to backup the program. However the new saved file, complete with comments is only 134 KB, and the very original copy of the program is 230 KB, from 2003. Is there a reason for this, the program hasn't shrunk in size, only minor tweaking of some span calibration numbers.
  22. MBE Driver can't save config file

    Hello!I am using MBE Driver v7.46b on Windows Server 2012 R2. Problem is that I can't save config file. I can edit Channels, devices and data blocks, I can see incomming values, I save a file without any message. But config file is not saved. In Event viewer I get error as you can see on picture. It says: Error writing to system registry: Driver App 00000001 \Driver defaults. Other error says: Error writing to system registry: ServerMsg 00C54BB8 \Driver defaults.Is it server or driver problem? Please help. At the moment I can't edit anything in driver so I can't configure it to use it with my SCADA iFIX 5.8
  23. Hello folks,   I am a rookie, self-training in PLC programming. I have written an SFC exercise (attached ACD file). I also try to call STL written subroutines and add-on instructions, from within the SFC main program. Calling the created subroutine works fine, but calling the add-on instruction fails from a reason which is above my level. I tried, tried and tried different solutions, with no avail. I am either wrong in writing the add-on (perhaps some missing but missing tag ?), or wrong is calling it. Can someone please give me a hint on what I do wrong ?   Thank you, Radu PS . I use Studio 5000 v24, combined with RSLogix 5000 Emulator.     SFC_trial.ACD
  24. CID and ICD file creation. Hi, I have a system that is using a PowerLogic G3200 to convert Allen Bradley MicroLogix 1100 Modbus to IEC 61850, but I am lost when it comes to creating an ICD / CID file. Does anyone have any experience in doing this? I have no help from Schneider technical support, they say the G3200 is not supported. Thanks in advance. Steve
  25. We have Q06UDEHCPU PLC.   We require to attain 1k of file registers in standard Ram. Please find our settings attached - PLC Parameter.png; When we try to down the register file – we attain the following error; “Failed to access standard Ram” error message (attached - Downloading Error.png); The program is very small – and thus we have plenty of space as well.