Search the Community

Showing results for tags 'unit setup not accepting ip address'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 38 results

  1. cp1w-cif01

    hello... i need  help for , how to set up cp1w-cif01 unit in plc for print barcode label. on Omron PLC.
  2. PID I & D Unit

    Hi All,  I need some clarification on the PID instruction. The note states that if #9 is set for C+6 04-07, the I & D will be 0.1 to 819.1s. But I didn't understand this highlighted section. Does it mean that my I and D values will something between  (1x τ)~(8191xτ)s??   All help is much appreciated, Stay safe and healthy. T J Sharon
  3. TIA Portal V13- Alarm for Bool Data type

    IN TIA Portal V13 HMI Alarm Setup, Discrete Alarm Not allowing Bool Tags in "Tag Trigger". Please help how to set Bool Alarms?
  4. Here are some videos training PLC AB(Rockwell) RSLogix5000 I hope this helping someones! 1) Setup RSLink to connect PLC using a USB cable   https://www.youtube.com/watch?v=mk-wgnwO4E82) How to set up hardware involve Input/Output, Analog, Device Net... PLC AB(Rockwell) RSLogix5000https://www.youtube.com/watch?v=pIUNPCEcNn03) How to use timer/counter/Compare PLC AB(Rockwell) RSLogix5000https://www.youtube.com/watch?v=7BDzAoFBJPMhttps://www.youtube.com/watch?v=EM3KO8JSYsMhttps://www.youtube.com/watch?v=yQtrIhTmwqA4) How to use Analog PLC AB(Rockwell) RSLogix5000https://www.youtube.com/watch?v=8raR0f7zr6M5) How to use RealTime-Clock PLC AB(RockWell) RSLogix5000https://www.youtube.com/watch?v=Lgg8hjs5jkY    
  5. I am trying to get produced and consumed tags set up between 2 1756 racks with different ip's. The 1st rack has an ip address 172.28.6.3. The 2nd rack has an ip address of 10.81.105.8. Would this be as simple as adding an EN2T card to one of the racks and setting the ip of one onto the same network? Or is there a better way to do this?
  6. Q02HCPU- Unit Verify Error

    Hello to all I have a mitsubishi electric plc Q-series (q02hcpu) with 2 Position card (qd75m4) for controlling 4 servo motor (mr-j2s-350b).  I have a new problem with. PLC after working for a few minutes, The Error light on the CPU  and position card turns on and the PLC STOP Working. Please help me fix the problem VID-20190806-WA0004.mp4
  7. CCLink

    Hi guys, I've just completed pre-commissioning on a Mitsubishi project which uses CCLink. My remit was to get the CCLink network up and running which I eventually did but not without issues. Basically, my problem was to do with the number of bits and registers consumed by a station. I read in a manual that each station consumes 32 bits and 4 registers for read and 32 bits and 4 registers for write. On my network I had 3 ST1H-BT modules occupying 2 stations each and 3 non Mitsubishi devices occupying 4 stations apiece. My RWr address starts at W300 and RWw at W500. Like I said everything matched up and I/O checks completed successfully. My question is, and I've trawled through the manuals looking for an answer, how is the number of points calculate? For example my non-Mitsubishi devices they occupy 4 stations, Expanded Cyclic Setting is Octuple and the number of points is 896. How is the 896 calculated? Thanks in advance
  8. Hi Guys I was wondering if any one of you could tell me how to set up some basic button functions? I need a basic instruction on how the followering button setup, could be done on the HMI, preferable with exaples or tutorials etc. !!! I´m working with the current setup: NX1P2, using Sysmac Studio, Module version 1.25.1.0, along with a NA5-Terminal, version 1.18 !!!  START_VALVE_1_BUTTON = Toggle, Momentary, Set or ?? - (Need the START_VALVE_1_BUTTON to activate ON_BUTTON & OFF_BUTTON flashing, indicating selection option, ON or OFF, meaning activating start valve 1 mode, or deactivate the mode). START_VALVE_2_BUTTON = Toggle, Momentary, Set or ?? - (Need the START_VALVE_2_BUTTON to activate ON_BUTTON & OFF_BUTTON flashing, indicating selection option, ON or OFF, meaning activating start valve 2 mode, or deactivate the mode). ON_BUTTON = Toggle, Momentary, Set or ?? - (Need the OK_BUTTON & the OFF_BUTTON to flash simoustaniously, after START_VALVE_1_BUTTON, or START VALVE_2_BUTTON has been pushed). OFF_BUTTON = Toggle, Momentary, Set or ?? - (Need the ON_BUTTON & the OFF_BUTTON to flash simoustaniously, after START_VALVE_1_BUTTON, or START VALVE_2_BUTTON has been pushed).  !!! Hoping to hear BACK from some of you VERY soon, because I need the know_how ASAP. !!! !!! Write soon !!!
  9. Hi everyone My system consists of 2 main stations with 2 CPU Q06UDEH and connected together by QJ71GP21S-SX module but I don't know how to link the address between these 2 CPU together? so can anyone help me? Thanks so much   
  10. We have an iQ-r R08cpu that will not display some labels or addresses.  The PLC and the machine it controls run as expected.  However, when we read from the PLC, some of the labels and addresses are not shown.  Although it runs as expected, we are hesitant to make any changes or write to the PLC. There is a screenshot attached.  Any advice or solutions for this?
  11. CompactLogix L35E

    Hi folks, I'm trying to communicate with an old CompactLogix L35E via Ethernet. I have already establish communication via DF1 Serial port and was able to go online but I Do not know the IP address to communicate via Ethernet. Can someone please tell me how I could determine the IP Address or create a new one ? This Controller was remove from a working machine. Any help will be highly appreciated. Thanks, Anthony.  
  12. hallo all, I want to ask if I click "read PLC Data" the "points" will appear, I use the QY18A output module that uses 8 points but there is no choice, the smallest is only 16 points.  so I can't put 148 in the "start XY" column ... will it affect the I / O address in the program?
  13. Lets say i have a PLC, with a name PLC1 with IP/Subnet of 10.125.34.243/255.255.255.0 I have to communicate this PLC1 with 2 other PLC's, PLC2 and PLC3 PLC2 with IP/Subnet of 10.125.34.10/255.255.0.0 PLC3 with IP/Subnet of 10.125.46.10/255.255.0.0 I imagine that, all these three are in different subnets, and so there should be no communication at all, but when i tested it, PLC1 to talking to/from PLC2 and not PLC3.  anyone know the answer to this ? How does it talk to PLC2 with different subnet, but not PLC3 which is in different subnet as well. 
  14. Please assist me with the following; regarding the ME96SSHA-MB Power meter data transition with Melsec-Q series PLC; We acquire to read various values on dedicated Modbus storage address registers at the simultaneous into a Melsec-Q series PLC via Modbus (TCP or RTU)  for calculation purposes. Naturally, since the reading of these variables are to provide accurate instantaneous results, it is a requirement that these values are to be read at one scan.   However, as can be seen below, there is a gap in address register range – of which, if all of these are scanned simultaneously, yields an exception error when read. This error is only avoided by scanning these data sets separately – which is not ideal for our application – since accuracy in calculations is imperative.
  15. Please assist me with the following; regarding the ME96SSHA-MB Power meter data transition with Melsec-Q series PLC; We acquire to read various values on dedicated Modbus storage address registers at the simultaneous into a Melsec-Q series PLC via Modbus (TCP or RTU)  for calculation purposes. Naturally, since the reading of these variables are to provide accurate instantaneous results, it is a requirement that these values are to be read at one scan.   However, as can be seen below, there is a gap in address register range – of which, if all of these are scanned simultaneously, yields an exception error when read. This error is only avoided by scanning these data sets separately – which is not ideal for our application – since accuracy in calculations is imperative.
  16. CX-Supervisor 3.4.1

    Hi After updating CXS to ver. 3.4.1 I can't see point address I can see them when I editing but in the list form only the array len. is shown. When I enter a new point I can see the address. Anybody now hove to solve that ? Banker
  17. Double address - Alarm

    Hello, I would like to see your logical opinion about this situation and in which part of system where I need to find solution - software or in the physical field. Subject: Twelve old system based on Mitsubishi PLC AnS series, Profibus Here is pneumatic transport, with 5 lines, each line have a shredder and discharge valve. A few months ago, when line 1 works , display shows line 2 and vice versa, it was first problem, but the system was still working. From the last week system doesn't work. On the display appear line 3 in works, but system can not started. Alarm shows Double address (perhaps two valves have some address), Alarm still appear after reset and even all lines are turned off. What is your opinion where to find proble (PLC, I/O moduls, cables,...)  
  18. Hello.   I'm trying to communicate between two PLC's  using FINS function block _CPU011:ReceiveData.   PLC1: IP 192.168.1.50 (MASTER)   PLC2:IP 192.168.1.51 (SLAVE)   If I don't use »IP Address Table« everything works using NODE number &51.       The problem is that on the real project these two PLC's will be on different subnet.   For example:   PLC1: IP 192.168.1.50   PLC2: IP 192.168.2.50   So I will have to use »IP Address Table« to achieve communication between these two PLC's.   I tried to sett IP Address Table on MASTER: Node 1=192.168.2.50   But If I try to communicate I see that packet is sended to network but I've got error #1005.   Do I have to sett the SLAVE IP Address Table?   Hoe to do this?   What are the right settings for MASTER and SLAVE IP Address Table?     I'm attaching pictures of CARD settings.  I don't want to use CX-Integrator because I would like to make project to UPLOAD and forget.       Thanks.  
  19. Dear all, I'm first time using M580 (hotstandby). Now finish the configuration, but the problem is how to write the address for Digital Input, Digital Output, Analog Input, and RTD module in elementary variable ? I try to put name DDI_1 and the address is same with M340 topology like %I2.1.0.1.1  and for digital input but got message after build : {Elementary Variables}    :     The instance is located on an address that isn't configured. :     DDI_1 Thank you for your advice regards  
  20. Dear all Please identify me i am having one Issue in my PLC.When I changed the IP of my plc then suddenly its showing error ERH its mean IP address wrong but  My CPU setting is same like previous means unit no=0, x16^0=0 ,Node=x16^0=1  and IP is 192.168.0.15 Mask add.255.255.255.0. but when I, transfer to PLC (in Program Mode) its not transferred(Failed to Transfer) please rectify me where I am doing wrong.
  21. I READ IN THE MANUAL FOR THE CJ2M-CPU34 THAT IT IS POSSIBLE TO CHANGE THE IP ADDRESS BY WRITING TO D30098 AND D30099 (MY DEVICE IS UNIT 0).  I TRIED TO DO THIS ON A TEST PLC BUT AM NOT HAVING ANY LUCK... I WROTE MY IP ADDRESS #C0A8 TO D30098 AND #0E30 TO D30099 (IP ADDRESS 192.168.14.48) WITH THE CPU IN PROGRAM MODE, I SET THE RESET BIT (A501.00) TO TURN ON ON THE TRAILING EDGE OF THE FIRST SCAN BIT, I CAN TELL THE CARD RESETS BECAUSE I AM CONNECTED VIA ETHERNET AND I GET DISCONNECTED, BUT THE IP ADDRESS DOES NOT CHANGE.  IS THERE ANY WAY TO CHANGE THE IP ADDRESS WITHOUT CX-PROGRAMMER?  I NEED TO GET A SOLUTION TO MY CUSTOMER TONIGHT AND MY SUPERVISORS DO NOT WANT TO RELEASE OUR DEVELOPMENT CODE TO THE END USER.   THANK YOU!!!
  22. FR-DU04 (FR-A500) vs FR-DU04-1 (FR-V500). Programming unit differences. (A VSD question) What is the difference between these units? Why are they not interchangeable. (Other than the fact that the FR-DU04-1 is used for vector VSD applications, and the FR-DU04 is intended for standard induction motor applications. Is this a matter of firmware differences?
  23. I have entered the messages many times into the Alarm Setup but every time i re-open the alarm setup, every message that has the Trigger Value=1 will be deleted.  Anyone have a similar issue?
  24. hi.  i want to make some program that work with indirect adress. example, i make program with many much type. I make with Got-1000 mitsubishi.   can you bring me some example? i am sorry, my english is Bad
  25. HI Everyone,  Recently i have bought a plc fx3ge and gt2000 hmi .the problem is that whenever i use a device address d280.b1 in hmi .i am not able to use the same address in gx works for plc (LD D280.1).can anyone help me with this problem.