Search the Community

Showing results for tags 'unit number duplicate error 0x80e9'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 167 results

  1. Hi all, I have an issue with Mitsubishi GOT Simple Series. After write to GOT, everything okay. All the hmi button functioning well. But after turn off and on the hmi, It will appear "SCREEN ERROR".  Any idea what can I check? 
  2. Hi all, I have an issue with Mitsubishi GOT Simple Series. After write to GOT, everything okay. All the hmi button functioning well. But after turn off and on the hmi, It will appear "SCREEN ERROR".  Any idea what can I check? 
  3. Hi all , I have been using MELSEC - Q series plc for the past two project i dont find any issue with that but for the third project  used same PLC same model but there is issue which I found unable to resolve  The issue is when i try to communicate PLC using LAN cable by direct ethernet connection it works normally but by communicating using HUB network I cannot communicate, I checked all the parameters setting, I dont know what is the issue even contacted mitshubshi service to troubleshoot but they are not responding  So here i am for your guidence to solve this issue   see the images below to analyse this issue This connection is direct ethernet connection which works normally    The parameters are set and writed to PLC The IP is set to my PC for communication  When i try to find the cpu in the network it shows the cpu IP  After that I checked for connection Test it show error I have also attached the Network route which i used to communicate  Network Drawing.pdf I hope someone will help me to solve this issue Thank you , madhan ravichandran
  4. Hello,   I hope somebody can help me give me hint on where I could look. I do have an MAM command that is throwing error 11. "At least one axis is not configured to a physical motion module ora has not been assigned to a Motion Group." The error message itself is clear but the Servo is running flawless until it suddendly stops doing this (the customer states that it mostly happens after an EStop). The EStop is hardwired via the STO inputs and those are active while the error is shown. So far the only way to reset the error is to shutdown the machine and power it up again. I can't find any errors in the error logs that would hint to dig deeper. Has anyone had this error or knows how to solve this?   PLC: CompactLogix 5370 Servo: Kinetix 5500
  5. Mewnet RS232c

    I wanted to online in FPWIN GR7s to FP-X C30t but it show MEWNET device
  6. GOT2000_Comset & GOT2000_Slave

  7. Hello! I'm currently using NB designer v1.531 (Build 210511) and I'm having compilation errors. It states: Connecting... Connection Error PT HMI0 Compilation error! Cannot create pkg files! I'm have trouble understanding, what does this error mean? I'm not connecting to any HMI, I just want to compile the program and test it offline. The weirdest thing is that if i click "Compile" enough times, it will eventually compile, but this is really interrupting the workflow. Does anybody else have this issue?  
  8. I am trying to setup a CC Link between two machines. I have done this before without issue, but for some reason this is not going well.. I added a second CC link card to CPU2 and set it as ST 24 for the CPU1 network.  CPU 1 : Master.   cc0.jpg.   The original machine was setup using TO/From for each station, so i couldn't add this new link through the GUI.  CPU 2: Local cc1.jpg  When i try to use the GUI to setup this side the buffer stops working. but if i activate any TO/From instruction here i get a system fault with a 2110 SP. Unit Error CPU2 buffer cc2.jpg. But when i block the TO/From you can see the buffer is working at that exact same location specified.    2110 error says I am addressing the wrong card but the buffer proves that I am not. 
  9. Hi all, I recently found out that you can turn on this option to allow the keyboard on your PC/laptop to enter values for data entry fields on the GT Simulator3 (screenshot attached).  I realize there are many people on this forum that probably already know about this but in case there is anyone out there that didn't already know...I hope you find this useful. This is a big deal to me because I like to thoroughly test my PLC code and HMIs/GOTs and now having to create screens with many entry-fields, being able to use the keyboard instead of dragging the mouse over the screen click here, click there just to enter values saves a lot of time and tedium. I wish someone had shown me this 12 months ago.  
  10. Mitsubishi safety relay

    Hello guys! A would like to set up a new inverter for my existing machine. I wanna follow the recomandation about the safety wiring. The only problem is I need one more, Z safety output. I checked, there is official expansion unit, and it says I have to only connect the EA, EB, EG, and EP terminals ? Do I have to connect again the X0, COM0 ; X1, COM1 terminals, because I want actually the same inputs, just I need one more safety relay output. I attached picture about it, thanks ahead. 
  11. Hello, has anyone noticed that plenty (not all) forum posts are changed to quotes from TWControls? What is happening here?  Hopefully only a momentary breakdown  
  12. i just got my NX1p2-1140DT controller with a R88D-KN04-ECT. i conneted every thing and directy got the 87 message on the display. i found out dat is becous wrong wiring I dont have the I/o cable incallt with omron they where saying that i don't need it and i can controll the motor controller full via ethercat. i already try to change to pdo mapping. what am i doing wrong? can someone help me? is it indeed true i dont need the i/o cable  thanks in advance for helping.
  13. Array A INT[32] Array Index B INT Destination C INT I am trying to move an Array (A) Element (A[2]) using a symbol (B) in ladder into a destination symbol (C) C = A [ B ] Result: ERROR: Array Index of Operand 1 out of range at rung 1 ( 6, 0 ).  The documentation suggests that it is possible, but I am unsure if there is something I am doing incorrectly. Note* Fixed indexing works with no errors Is there another method to accomplish this?   PLC : CJ2M CPU31 CX- Programmer: Verion 9.74 Update 1: If I go online to the PLC It does look like the array look up is working. Is the issue with the mov block? Update 2: I changed the memory locations which has caused a different error to appear. This error is clearer but does not explain the manual excerpt I posted further up ERROR: Only the constant can be specified for the index of the array.  at rung 5 ( 6, 0 ).  Update 3: Solution 1 I managed to hack together a proof of concept using pointers and indirect offsets  Update 4: Solution 2 For some strange reason things work as expected inside of the function blocks so I made one where the array is In-Out and with an input and output respectively. Note* External reference to pointers inside of the function block produced an error. Function block Logic     Update 5: Solution 3 Now I feel like I am going crazy, I tried just the original code again and it works... I have no idea why and if it was not for all the documentation I would be lost as to why it works now... Update 6: Conclusion It seems to have array indexing work the array index must exist in the D Memory Block. The reason it did not work above is because I somehow had a MOVR block when I tested after moving all the variables to the D Memory Block. I hope this journey helps someone else :)
  14. OMRON CJ1W-ETN21 Node Number

    Hello. I'm having CJ1M unit with ETN21 card on remote site. I can't drive to the site and look at the rotary switches to determine what is the units NODE NUMBER. I can connect to the PLC remotely using CX-Programmer. Is it possible to read the setting of NODE NUMBER remotely? Is this NODE NUMBER settings saved somewhere in CIO or DM area? Thanks. BR, Andrej.
  15. CP1W TS001

    Hai, I have problem with my CP1W TS001, suddenly reading result always #7FFE.  i use CP1E-N60 and 2 expansion module, AD041 and TS001. I put TS001 after AD041 then my program code as follows : mov #8051 105 mov 7 D20 mov 8 D22 the reasult at D20 & D22 always #7FFE could someone help me to solve this problem?
  16. Hello fellow tinkerers, Inside our company we're expanding our IoT network with the replacement of CJ1G-H to CJ2M CPU units. When swapping models we are downloading the Datamemories back into the CPU. Our engineer warned us to not download all the DM memories: only up to D20000, so I did. When starting we had some inputs that weren't showing in the Data trace: and noticed that it were pulses shorter than 8ms. We found out the "Unit settings" were back to default and this is not unusual since we only downloaded range D0-D20000 but I'd like to avoid this in the future and look up what each datamemory means. I know D30000 to D31599 are the memories for the CPU bus unit settings (manual W473 section 4-5) but what range is the "unit settings" within these 1600 datamemories? I can't seem to find it in any manual I look into (W473, W472).. Also do you see any problems with downloading the full datamemory range?   Kind regards!
  17. Hello. I am writing a function block and i am getting the following error: ERROR: STRING type or an Input Output variable is not supported by the PLC of this unit version. Check the unit version in program check options. When i try to remove the string i get error: instruction is not available for current plc Is there somewhere where i can see which instructions i can use? Or is it not the string or one of my in or outputs I am doing something wrong with?   Kind regards, Ralf  
  18. Q02CPU Error 2200

    Hi All; Trying to make a backup of a Q02CPU.  Used GXWorks2 to get the program and parameter files from the working CPU.  The System is on an 8-slot rack with mixed IO including a ProfiBus module (QJ71). Got a new CPU, powered down the system and installed it after setting the DIP switches the same as the working one (2 and 3 both on, others off). Power on system. Download the program and parameters to the unit, have the ERR LED blinking and the CPU will not run.  PLC Diagnostics show this 2200 error, which when I look it up in the book starts talking about 'drives', which I find out have something to do with the DIP switches.  The combination of switches 2 and 3 indicate the parameters are to be stored in Standard ROM (Drive 4), but apparently this is not happening when I do the download of the program and parameters.   Is there a specific procedure I need to follow to put the parameters into Standard ROM (Drive 4)? Or, did I get a replacement CPU that is either A)Bad or B)does not have this Standard ROM? Or...?   Any assistance would be appreciated.   CPRenaud
  19. Hi all,I'm completely new to ASCII and trying to figure out where I'm going wrong here.Application: I need to send 2d barcode data to a KGK Jet model CCS3000L Inkjet printer. Only protocol possibility is ASCII. PLC I have is a Micro850, and the only port option for ASCII is the serial port. I modified one end of a 2707-NC11 cable to connect PLC TxD to printer RxD, PLC RxD to Printer TxD, and PLC SG to Printer SG. I jumpered CTS and RTS at the printer connector, and the 2707 cable I'm using doesn't have wires on the Micro850 CTS or RTS pins.Printer company verified that I can just jumper RTS and CTS on their side and not connect their DTR and DSR pins (since I'm not using hardware handshaking). I don't really need any flow control for the application ( I don't think...again, ASCII noob here).Do the CTS and RTS on the PLC side need to be jumpered? Does the DCD pin need to be jumpered or connected to something if I'm not using handshaking?I downloaded the Micro800 ASCII read and write functions and function blocks from Rockwell library, and they seem to be working, except that I keep getting ABL error id "7". This error states, "Cannot complete ASCII send or receive because channel configuration has been shut down using the channel configuration dialog box." I have the serial port enabled and configured to ASCII, no handshaking, baud 9600 same as printer, no parity check, 1 stop bit, character length of 8.Any help in pointing out what I'm doing wrong or things to try would be greatly appreciated!   ASCII_TEST.ccwsln
  20. Trying to log into NA HMI, NA5-7U001B  Direct, using USB or Ethernet.  All attempts failed .. tho, it was easy to log into the NJ Controller, direct, with USB or Ethernet using the same PC. Then a window popped up.. saying the firmware needed updating in the HMI, and suggested launching the "update" from the same window... Then, after a few minutes.  a "update failed" was displayed on the window.. and the HMI screen changed to this: ..and the green LED went RED ... aaaaagh!   HMI no longer works... any idea why this happened, or the failure to log in happened.. or, what it will take to fix it? Please tell me it was something Omron did .... Thanks Much, Regards, ,Michael PS:  additional info..  I was using Sysmac Studio Version 1.1 .. because I could log in to the CPU (USB and Ethernet) and not the HMI.. I changed to another PC with Sysmac Studio Version 1.17 .. Now I was only able to log into the CPU with Ethernet.. USB login failed. .. and, so did any attempt to log in to the HMI (USB or Ethernet) It looks like if you use a new version of Sysmac.. better not have a device with  "old firmware" ..  I think it was the V1.17 that presented the window suggesting the Firmware Update ...  sigh!
  21. CP1E won't connect or run program

    Hi there! Today a CP1E-E10DR-D suddenly stopped working. RUN led was off and I couldn't connect to it via USB getting this error: "Selected port does not exist. Select proper port number from Change PLC dialog and press OK button", and automatic online function didn't work as well(it's not a cable/driver problem since I successfully connected to a CJ2 CPU using same cable and PC). Since I also tried to connect with the CPU outside the control cabinet with no success, I asume there is something wrong at hardware level.  My question is, have you ever faced something like this? My plan is to try to revive it somehow (maybe trying to locate any defective component in the PCBs or something). So I was just wondering if you have any advice in order to achieve it.  Thanks in advance!
  22. Omron NB Software

    I am facing the error while compiling the program , there is only 1 error , but not able to figure what is the actual error. Please suggest and support.
  23. Q-Series - Operation Error 4100

    Hi guys. I found error on PLC and from PLC diagnostic I found this Operation Error 4100 as per attach picture. FYI, there is no SD card mount onto this PLC. I wonder what is ATA card. This error wont affect the operation. Any advise on what to check?   This ladder is pop up when I clicked, error jump.   Thanks.
  24. G9SP Configurator

    I am at a client site that has a line with multiple Omron G9SP-N20S safety controllers installed and I need to make a modification to the system.  I tried to install the Omron Configurator and it asks for a serial number, and will not install without one.  Omron said that it is on the CD that ships with the unit, but the equipment manufacturer did not supply any of the CDs.  The only Omron solution is to order a replacement CD, that will take 5 days, which is 5 days too long as there is a hard stop in 2 days.  I have tried entering numbers found on the controller, with no success.  Does anyone have a better way, special contacts at Omron, to et it faster?
  25. Hi guys. I was getting Coordinates error popped up everytime I tried to go the page. If click OK, everything is normal and can operate as usual. Just wondering how to eliminate and what causing this error. Thanks!