Search the Community

Showing results for tags 'status register'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 25 results

  1. Dear Engineerds,   My Master (non siemens) doesn't see the Holding Registers of the Slave (S7-1200) plc. However the Q coils are fine and all Diagnostics don't show errors. The Hardware: S7-1200 – CPU 1215C CM PtP – CB1241 RS485 (6ES7 241-1CH30-1XB0) - Half Duplex RS584   Firmware: Modbus_Comm_Load (V3.1) Modbus_Slave (V4.0)   I've tried with various DB, UDTs and manipulating HR_Start_offset parameter with no success. Could you advise what am I possibly missing? Modbus_Comm_Load_DB_Snapshot.xlsx Modbus_Slave_DB_Snapshot.xlsx
  2. QM30VT2 BANNER WITH QJ71C24N

    Dear Sir. Can Anyone Help me,How To read  Holding Register QM30VT2 BANNER With QJ71C24N Mitsubishi ,With Rs 485 Communication.I Want To read Holding Register it,More than 2500 Register. Thank you for attention. Best Regards.
  3. Hello. I can't find any related bits wich would indicate PLC offline / online status. I'm using two PLC's. PLC0 Modbus TCP (Ethernet) PLC1 Modbus RTU (Serial) Please help me to get online status. BR, Andrej. 
  4. WRITE MULTIPLE REGISTER MODBUS

    Hallo my name is Danu, i have a CP1E wirh CP1W-CIF11 and connect to modbus RTU device, i have done with write single coil, write single register,  read single register and read multiple register. But i try to write multiple register,  the indicator of CP1W-CIF11 is off and if i check d memory its no data. I attached my cx programmer. Can you help me create write multiple register in cx programmer?  Thank you AD4402-modbus edit edit edit edit edit.cxp
  5. b&R 4PP015 Error

    I have a 4PP015.0420 panel with the led error that stays between green and red, and it doesn't work.The sequence of the LEDs at power:       Yellow   Red       Green   Red       Green   Green       Green   Green&RedAnd on the display :          Version    1.1          Status     400041000I think there is a Status Register that indicates the errors.How can I see it to know why the PLC is not put in RUN?Thank you in for your help.Sorry for my english
  6. I have IPC and need to detect status of IPC and PLC communication . I need help with the same that how can in detect it ? Is it possible with message instruction ? if it is then how ?
  7. floating point shift register

    hi all, i'm currently trying to shift register some data in the floating point (double word) format, just for an example i,m using a 0-20mA 0-40 bar pressure sensor to gather information from a can filler and want to log the data for lets say the previous 20 cans. i understand how the shift register works and can get it to work with single word just fine, im using floating point to make my life a bit easier by using sleepy wombat's scaling function block, i need decimal points as i will be expecting reading around 4.5 or so bar and expected to be within .2 tolerence this will then have to displayed on a HMI, which i assume will be easy enough
  8. Hi,   I'm pretty new to allen Bradley and wanted to know if there was a function that could help me out. I have a rotation sensor which feeds back to the PLC via a digital input, once every half second or second once machine is up to speed - I want to record the off time of this DI (how long it is off between pulses, essentially how long it takes for drum to rotate once). Is there some way to record this time and use this value for compare logic? any help would be greatly appreciated.   PLC: Micrologix 1400 series B RSLogix 500 version 11.00.00 (CPR 9)
  9. Hi, totally new to PLC's .. Just trying to do a university assignment I've connected a DTC1000 to Fatek PLC Port 2 - RS485 I want to know in which register I can find the measured temperature. A friend said you should add 400000 to the converted from hex to dec number which is mentioned in DTC manual. http://www.deltronic.su/userdata/files/dtc_manual_eng.pdf But I'm not sure which value should be used in manual and is 400000 the number to add (and where it has come from!) If I can just find the register, I can do the rest (just a bunch of normally open and close and  .. Thanks
  10. Please assist me with the following; regarding the ME96SSHA-MB Power meter data transition with Melsec-Q series PLC; We acquire to read various values on dedicated Modbus storage address registers at the simultaneous into a Melsec-Q series PLC via Modbus (TCP or RTU)  for calculation purposes. Naturally, since the reading of these variables are to provide accurate instantaneous results, it is a requirement that these values are to be read at one scan.   However, as can be seen below, there is a gap in address register range – of which, if all of these are scanned simultaneously, yields an exception error when read. This error is only avoided by scanning these data sets separately – which is not ideal for our application – since accuracy in calculations is imperative.
  11. Please assist me with the following; regarding the ME96SSHA-MB Power meter data transition with Melsec-Q series PLC; We acquire to read various values on dedicated Modbus storage address registers at the simultaneous into a Melsec-Q series PLC via Modbus (TCP or RTU)  for calculation purposes. Naturally, since the reading of these variables are to provide accurate instantaneous results, it is a requirement that these values are to be read at one scan.   However, as can be seen below, there is a gap in address register range – of which, if all of these are scanned simultaneously, yields an exception error when read. This error is only avoided by scanning these data sets separately – which is not ideal for our application – since accuracy in calculations is imperative.
  12. Link register in Q series plc

    How to use link register(w) in ladder program? And how can we configure that ? And How to read and write values to that register?
  13. Compare not working

    We have this logic (on a CP1E) the desired outcome is as follows: When a bad part is detected, force the operator to index the machine 6 times, using a holding register to prevent a power cycle from resetting the count. once 6 cycles are recorded output that the bad parts are removed AND reset the count to zero.   What has actually happened so far: the count has gone to 6 and not reset. I have used CX Programmer to set the H0 value to zero but the compare still says it's equal (to 6)   I have read everything i can get my hands on regarding holding registers and compare functions and i can't see what is wrong. I have no formal training on this so i'm sure it's something simple. can anyone point me in the right direction?   Thanks guys    
  14. bit shift register

    Hello everyone. I m new on site. I need to an example program (done and running properly) that bit shift register. I will design a bottle filling machine. I dont know how to use these logics.  hardware dosent matter.   thanks for your interest
  15. I have Omron CP1H PLC and using Ethernet Option board to communicate through Ethernet. When I connect PLC to 2 Computer it starts malfunctioning and values in register get fluctuate. while I connect single HMI it works fine. Kindly give solution if anyone know. 
  16. I'm looking for some general information about different types of vibration/temperature sensors. What type, brand, model number, etc. will best fit my application.  Scenario: I want to monitor the vibration and temperature of multiple motors and gearboxes for a large overhead conveyor system. If an oil leak occurs and temperature increases, I want to see a temp. alert via a HMI. If a something mechanical fails, I want to see a vibration alert via a HMI.  I've looked into sensors that stick to the outside housing of the motors or gearboxes via a magnet. My concern is justifying the temperature readings. How accurate would a sensor that reads an "ambient" temperature be (compared to a thermocouple on the motor coil itself or some sort of probe)? Also, would the location of the magnet  on the motor or gearbox drastically affect the temp. or vib. readings? Has anyone had success with a similar setup? If so, what devices did you utilize? Are these systems truly beneficial?  I'm currently considering Banner's wireless products...
  17. Hi everybody. I'm just getting started with GX Works 3 and I feel a bit lost. If I have an external help file for my function blocks, how do I register this in the program? I can't find it anywhere when I double-click the fb library or in the e-manual Viewer. The file format is .CHM and I have imported this to GXW2 earlier.   /Niklas
  18. Hai i want to know how to save and retain the values of the program even in Emergency power off the PLC and on again? can any one help me?
  19. Hi, Iam new to schneider electric PLC drive programming and also to canOpen communication. I have an LMC058 PLC and there are three Lexium 32A drives connected via canOpen which inturn controls three servomotors. My question is how to find/ read hardware limit status of the axis in which limit is connected to a digital input pin of the drive. Even though the axis is properly working by configuring the digital input pins we are unable to get the digital input status of the drive. In the drive manual its given that the digital input status can be read from canOpen address 3008:F(hex) we dont know how to read the status during run time in the program . Can any one advise me how to read that address. I tried SDO_read function but its giving me error(canOpen network id Unknown). Thanks in advance.
  20. Hello All! I am having difficulties mapping register values. In the TURCK register there are 24 unique register bytes corresponding to different value registers (8bit x 24). These 24(8bit) bytes were mapped into RSLOGIX 5000 as 12(16bit) INT words ....INT[12] .. This means there are 2 bytes (2 unique register values) inside each INT word. WHAT I NEED TO ACHIEVE: 1. (BLUE outline in drawing) Write/Map a value of "32" into byte 7 of the TURCK register so effectively starting at  INT[5].8 in RSLOGIX           Drawing1-Model.pdf This will enable the value of CNT1 (encoder count) to be registered in bytes 8-11... 2.  (PINK outline in drawing) READ/MAP the values registered in bytes8,9,10 and 11(4x8bits) into a SINGLE 32bit INT value which will tell me the CNT1 value of my encoder. I am having problems when ever I try to COP a value of 32 (no matter what kind of array it's sourced from) into INT[5].8 & I haven't tried to map/read the values of bytes 8-11 CAN SOMEONE PLEASE HELP EXPLAIN HOW TO ACHIEVE THIS?! Thanks for your input EVERYONE! :D Drawing1-Model.pdf
  21. E1151 New Display Register

    Hi all, I wonder if anyone can help me. I have 4 test rigs setup with E1151 HMIs and FX3U PLCs (with two ADCs and one DAC).  They are running pretty well, and the HMI changes block fine when using Jump to Block, but when I try to get the PLC to change the HMI's block using the New Display Reg it becomes very temperamental. For automatic testing I want the PLC to prompt the HMI to change block, so I set it up with a PLC register, then set the HMI to use this register for the New display reg.  When I turn the PLC and HMI on I can run through the test, and at the end it changes screen perfectly.  However if I run the test again the HMI appears to "forget" to change screen.  I have checked the new display register and It lists the correct screen, but the HMI doesn't change. So far I have tried adding "SCRR" too the command list to use short recipe names (saw this on a previous post), and tried reducing the amount to data transfer between the HMI and PLC to see if it was a latency issue, but neither have worked. Has anyone else witnessed problems like this?
  22. IR register operation

    Hello, Can I add an offset value to IR register? for example, MOVR D0, IR0 and I have an offset value stored in D1, for example, &100, could I add the offset of D1 into IR0, to get IR0 pointing to D100? I know I can just do MOVR D100, IR0, but for purpose of versatility, I want an offset to be added in such a way. Thanks in advance. Xing
  23. S7-300/400 Status to Wonderware

    I've been tasked with building several "maintenance" related HMI screens in our Wonderware application for systems running on S7-300 and S7-400 PLCs. I'd like to provide an overview of general PLC status for all PLCs, displaying this type of information: LED StatusStatus of Communication to WonderwareI/O FaultsModule faultsetcFirst on my list was LED Status. I found a Siemens tech document describing how to determine the status of each LED on the processor via PLC programming, but it occurs to me that it's pointless to do so for the Run or Stop LED's - if it's not in the Run state, then the code will not execute, therefor the HMI will always display a healthy status for those two LED's. I'm referring to a Siemens document entitled "Programming Example in Ladder Logic, Getting the Status for the CPU LED Indicators." It would be nice to be able to indicate if a PLC was faulted/stopped. Does anybody out there know of a way to do this with Wonderware? I'm fairly new to Siemens and Wonderware (mostly AB and iFix experience), so detailed answers will be much appreciated!
  24. I have had a GE 90-30 CPU331 in my house for 17 years with no trouble at all. I have a problem that I have never seen before. I was editing the program using LM90. I don't know what I could have done in the program to disable an output. Just 1. All the rest of the points in that group on that card still work. I swapped cards with no difference. All of the elements of the rung are true (highlighted). The output is not on or highlighted. The nickname over the output has ONE letter highlighted. The bit in the reference is "0" and is highlighted or "grayed out" (the cursor is not on it). I searched for coil conflicts. I am using this output contact lots of places but only one output. The logic is working correctly when I use another output or %M. This is an isolated output which needs to be in this group (moving it would be awkward). What does a "grayed out" reference bit mean?