Search the Community

Showing results for tags 'software program'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 153 results

  1. PLC trainee View File SFC test file; cant call an STL written add-on from SFC main program Submitter Radu Babau Submitted 02/04/19 Category PLC Sample Code
  2. Panasonic FP0 C14RS

    Hi All, I am new to the forum and new to programming PLC and like every newbie I have a lot of questions - Brief History of me - I had been a Manufacturing Technician for 20 years and recently got my BS on Electrical Engineering and now working as an Equipment Engineer. The main reason that got me interested in PLC's is my degree,  the field that I would like to get into and a recent problem that arise at work. My experience with PLC is very small in programming, some in TS I/O- However I had been studying by my self to the point that I built a test bench to understand it better and in the future create different project for learning purposes Currently I am putting together a tool Alarm delay program - Basically my exhaust sensors trigger an alarm (input signal turns OFF) before its send  the signal to my tool for abort, I want to create a different Alarm which will cause a different response from my tool and delay the original Alarm by 10 min and then trigger the original Alarm - PLC = Panasonic FP0C14RS  Reasons: Create a different Alarm: The response from my tool to this alarm will allow me to return my material back from the tool and put it in a safe spot. Delay the Alarm: Use a timer to perform this tasks - This the time that approx. it takes the to return the material. Trigger the original Alarm: I need to know which sensor was the problem in order to properly TS- So after my timer is complete - I want to know which sensor created the original Alarm My Current problem: I created the LD program, and while the original alarm stays OFF the program works fine - but since my exhaust sensor are always on - If my original alarm is trigger for  a few seconds, just enough to start my Delay Alarm: I dont have a way to know which sensor trigger after my Delay(Timer)is complete,  I reset my relays in order to be ready for new alarm.   Please provide feedback to my program - I know currently is not the best way or efficient way to do this and there are better ways, but my plan is to get it to work and then later revisions improve the way the program can be written   Thanks in advanced for your feedback and help Exh_delay_inv_rev1.pro
  3. ladder program

    Hello everyone, I want to know why the Y172 coil is ON / logic 1? whereas contact SM1 is worth OFF / logic 0? can anyone explain it to me ?
  4. Hello.. I have hmi Proface GP-4301TW, USB type B cable and ethernet cable. I want to transfer the program to the hmi but I cant. When I turn on the power of hmi,  a series of test appears and finally it looks like the photo below and I cant enter the offline menu.. can anybody help me to solve the problem?
  5. I have the following for sale. I would prefer to sell as a lot. I can send pics if there is any interest. EX40 + 20 IO Extension with 2 Unused output PCB for ext unit. 2 EX40 Plus PLC. Timer Counter access unit Operational. With 2 PCB with errors showing. Handheld Programmer (Squeekbox) excellent condition. CutlerHammer Original software with hardware dongle. Some spare parts, they were operational before I used for testing various functions. PM ME IF ANY INTEREST.
  6. Please,if anyone has a working program (.stx).I need it to test a PL7 JUNIOR software
  7. Hello, everyone. I want to ask for help..  i want to upgrade HMI hakko V7 to V9.. have file hmi in V7 use software V-SFTV5 but when I open file V7 use software V-SFTV6 its cant convert and i attached the screenshoot below..  can someone tell me what's wrong?
  8. Function Block

    Where would I find TC_2PID_Function_BLOCK? as described in the Temperature Regulation Solution, Quick Start Guide v1.02 Is there somewhere on the omron web site to find all up to date FB Libraries?
  9. Hi, In conception phase we currently use GXWorks to upload programs to PLC (L-Series). In production mode, for different security reasons we would like to automate this transfer so that the operator does not access directly to the program. Do you know any tool allowing this by using command lines and not GXWorks UI ? (GXWorks does not seem to be "command line" friendly As a POC I  have automated the GXWorks UI in C#  (by simulating menu or buttons clicks) but I don't find it reliable (what if an unexpected popup "pops" ? ). PS : I am a totally noob in this PLC world so maybe I missed stg in the docs ... 
  10. A machine was bought at auction which included PLC-5/15 module.  It did not come with a backup of the program.  Our maintenance technician said the program would not load and turned the module over to me (IT).  I notice the battery was installed in '92 so am assuming the program is lost.  Is their any internal memory or last ditch effort i can attempt to recover the program from this module?
  11. Hi Guys! You can read my problem below, if anybody can help, please do it. Thank you. So, I have 4 knife. You can set the cutting width for each knife separately. The problem is, there is a lot of size. There is an example: No1 size:  #1: 20 mm, #2: 25mm, #3: 30mm, #4: 25mm   (#1=Knife1.......)                                       No2 size: #1: 22mm, #2:24mm, #3: 32mm, #4: 27mm What is make the problem more difficult is There are plenty of type code too. Like X1, X2, X3, Y1, Y2, Y3 ..... This is the main material code. and you can choose the belogging size. So you can select for X1 to No1 or No2 ... but you can select for X2 to No1 or No2 or any sizegroup you want. I can solve it with a lot programming, like deal every possible situation ... but there is a lot time .... :S  There is a touch panel where you can set the values.  Anybody have another idea for this problem ?    
  12. We have a QSeries PLC. Q25HCPU. We also have a PLC program. We found that the address registers (also known as device addresses) attain a z-value added next to it - automatically over time. We are not sure why this is the case. Nonetheless, when these values get added (by the PLC - not the engineering software), some of the functions in the PLC doesn't work. We found that by formatting the CPU, and reloading the program, allows for the system to work again (temporarily) for a few weeks, up until this problem occurs again. This problem occurs across various CPUs (eliminating the potential for hardware problems. These z values can be seen when a program comparison is done. (see attached file). The questions become; 1. What is the function of these values? (why does the PLC add them? 2. How can they be permanently removed?
  13. We have a QSeries PLC. Q25HCPU. We also have a PLC program. We found that the address registers (also known as device addresses) attain a z-value added next to it - automatically over time. We are not sure why this is the case. Nonetheless, when these values get added (by the PLC - not the engineering software), some of the functions in the PLC doesn't work. We found that by formatting the CPU, and reloading the program, allows for the system to work again (temporarily) for a few weeks, up until this problem occurs again. This problem occurs across various CPUs (eliminating the potential for hardware problems. These z values can be seen when a program comparison is done. (see attached file). The questions become; 1. What is the function of these values? (why does the PLC add them? 2. How can they be permanently removed?
  14. My apologies for being a newbie on this, but could someone save me on this... I have a Viper 650 and an eMB-60R controller which I want to control by ePLC connection using an NJ501-1300 PLC unit, SYSMAC Studio with EIP Adept Library for Robot... All are starting up well, and I connect all components to a switch hub...  But following the ePLC guidelines, the IP Address showing on the controller is 172.16.132.111 I change the IPV4 IP Address on the PC settings to 172.16.132.10 and the subnet to 255.255.0.0 but the Adept IP Address Setting Tool on SYSMAC doesn't detect the Robot IP Address, also i tried ipconfig on command prompt which shows a different IP Address IPV4 169.254.197.75 and subnet of 255.255.0.0, I changed the previous setting on the PC setting to 169.254.197.10 with the same subnet. But still PC doesn't recognize. I tried both configurations if ACE Software can detect it but the same ACE can not detect it also... Appreciate any thoughts on what's wrong in my configurations. Thank you.
  15. Fuji Wsz plc

    Please send Fuji Wsz plc software download link  
  16. Fuji Wsz plc

    Please send Plc software link
  17. Currently, our SCADA setup uses Kepware, Wonderware, and Canary Labs data logger and historian. The data flow is as follows:  PLCs --> Kepware (on PC near process) Kepware --> Canary Data Logger (on PC near process) Canary Data Logger --> Canary Historian (on Server) Canary Historian --> Canary Axiom Viewer Client (on engineer's PC) We use Wonderware as an HMI on the Process PC to control the process. As many will know, this is very wasteful as Wonderware includes many other features and we are paying for all of them yet using only the HMI feature. Our goal is to cut Wonderware out of the equation (i am aware that Wonderware  could replace both Canary and Kepware with its data logger and OPC server features but this is the direction that was chosen so we are going with it).  My question is: Does anyone know of any simple and cheap (-er than Wonderware) PC-based HMI software that could replace Wonderware on the Process PC?
  18. Hello i'm new in all things about plc, i do a project for school and i use a festo fc 34 plc. The plc is programmed via serial port RS232 my pc not support a serial interface and i use a RS232 to usb adapter. when a try to download the program to plc give me a error: "ERROR: Cannot access controller".  What i do wrong.  Thank you in advance and sorry for my English. Have a nice day.
  19. Help with Fx0s 30MR

    Hi there, just need a little help, I’m very interested to learn all about plcs, I know the basics and I know how to wire them, programming them is the hard bit! Ive got an FxOS MR30 from work, to play around with, I know I also need Gx developer also,  my question is,  could I use gx developer “micro fx “ for this?    It seems to be a lot cheaper than the normal go developer.http://ie.farnell.com/mitsubishi/gx-developer-fx/software-micro-fx-plc/dp/3825577 any help with this would be great thanks 
  20. PLC Training

    Hi Everyone We are setting up a initial training in PLC programming for technicians, I got some experience with SIEMENS S7 but this seems to be an expensive choice, we would like to opt for a budget PLC but at the same time would like a user friendly software for teaching......I would like to have views of users of other PLC brands such as OMRON, MITSUBISHI or even Schneider??? thanks Jay
  21. FX3sa-20MR

    Hello everyone, Have a nice day to all. We just received a small machine from china, and definitely we done a lot of modification to add  safety and other sequence, to adapt this machine to the existing line. I'm familiar with siemens and omron, and this is my first time for mitsubishi PLC. FX3sA-20MR, can somebody pls. help me what software do i need to download and programming cable to communicate with the PLC. Thank you in advance...
  22. Looking for Socket TCP/IP communications program examples for Mitsubishi PLC iQ-R R04CPU using GX Works3, to compliment the Mitsubishi Ethernet manual Socket commands instructions. Unfortunately, the manual is missing real application ladder logic illustration examples of these commands. For example, the Socket Open Connection command, does not describe in what order or format to enter the IP Address.   For example, to enter IP Address 192.168.1.100, does the most significant octet 192 is entered or stored first in the lowest memory storage register (Big Endian format) or does the least significant octet 100 is entered or stored first in the lowest memory storage register (Little Endian format)? I am trying to write a simple Socket TCP/IP communications command that will write about four registers from an existing Mitsubishi PLC R04CPU (Socket Client) to an Allen Bradley PLC ControlLogix (Socket Server). .
  23. I'm using Controllogix L61 redundancy system as a slave with DCS using ethernet tcp/ip socket programming. The communication between master and slave will fail after a switchover. Kindly give solution for this. Thanks and regards, Rasu
  24. CX-Thermo program

    Hello, I am working with e5cc-t programs, for heating application. I need to find a way, to start program, when temperature reaches set-point of first (no. 0) segment. I think that, there should be some kind of setting, but i cant found it.. I've done this with PLC, but this is not an solution for this application. in conclusion: After program starts, it has to reach set point temp, and then hold temperature for certain time.  
  25. Fx3s plc

    Hi, all version gx work2 can support FX3s? Im using version 1 gx works 2 and currently got new fx3s-10mr/es w/out program..i tried to make new program but fx3s ot included in this software